Nissan Juke F15. Instruction — part 271
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
DLN-89
< SYMPTOM DIAGNOSIS >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000012199455
Use the chart below to find the cause of the symptom. The numbers indicate the order of the inspection. If necessary, repair or replace these
parts.
Reference
"
n"
SUSPECTED PARTS
(Possible cause)
T
R
ANSFER OIL (Level
low
)
T
R
ANSFER OIL (W
rong)
T
R
ANSFER OIL (Level
too high)
LI
QUI
D
GASKET (Dam
ag
ed
)
OIL
SEAL
(W
orn
or da
ma
ge
d)
GEAR
(W
orn
o
r
da
ma
ge
d)
B
EARING
(W
orn
or
da
ma
ge
d)
Symptom
Noise
1
2
3
3
3
Transfer oil leakage
3
1
2
2
DLN-90
< PERIODIC MAINTENANCE >
[TRANSFER: TY21B]
TRANSFER OIL
PERIODIC MAINTENANCE
TRANSFER OIL
Inspection
INFOID:0000000012199456
OIL LEAKAGE
Check transfer surrounding area (oil seal, drain plug, filler plug, and transfer case etc.) for oil leakage.
OIL LEVEL
1. Remove filler plug (1) and gasket. Then check that oil is filled up
from mounting hole for the filler plug.
CAUTION:
Never start engine while checking oil level.
2. Before installing filler plug, set a new gasket. Install filler plug on
transfer and tighten to the specified torque. Refer to
CAUTION:
Never reuse gasket.
Draining
INFOID:0000000012199457
1. Run the vehicle to warm up the transfer unit sufficiently.
2. Stop the engine and remove the drain plug (1) and gasket to
drain the transfer oil.
3. Before installing drain plug, set a new gasket. Install drain plug
on the transfer and tighten to the specified torque. Refer to
CAUTION:
Never reuse gasket.
Refilling
INFOID:0000000012199458
1. Remove filler plug (1) and gasket. Then fill oil up to mounting
hole for the filler plug.
CAUTION:
Carefully fill the oil. (Fill up for approximately 3 minutes.)
2. Leave the vehicle for 3 minutes, and check the oil level again.
3. Before installing filler plug, set a new gasket. Install filler plug on transfer and tighten to the specified
CAUTION:
Never reuse gasket.
: Vehicle front
JSDIA2080ZZ
: Vehicle front
JSDIA2081ZZ
: Vehicle front
Oil and viscosity
: Refer to
.
Oil capacity
: Refer to
.
JSDIA2080ZZ
AWD CONTROL MODULE
DLN-91
< REMOVAL AND INSTALLATION >
[TRANSFER: TY21B]
C
E
F
G
H
I
J
K
L
M
A
B
DLN
N
O
P
REMOVAL AND INSTALLATION
AWD CONTROL MODULE
Exploded View
INFOID:0000000012199459
Removal and Installation
INFOID:0000000012199460
REMOVAL
1. Turn the ignition switch OFF.
2. Remove front seat (left side). Refer to
SE-21, "Removal and Installation"
.
3. Remove dush side finisher (left side). Refer to
INT-21, "DASH SIDE FINISHER : Removal and Installa-
4. Remove front and rear kicking plate inner. Refer to
INT-19, "KICKING PLATE INNER : Removal and
.
5. Remove rear seat cushion. Refer to
SE-32, "SEAT CUSHION : Removal and Installation"
.
6. Remove outer anchor of front seat belt (passenger side). Refer to
.
7. Remove harness clip.
8. Turn floor carpet. Refer to
INT-24, "Removal and Installation"
.
9. Disconnect AWD control module harness connector.
10. Remove AWD control module mounting nuts.
11. Remove AWD control module.
INSTALLATION
Note the following, and install in the reverse order of removal.
• When installing AWD control module, install it following procedure.
1.
AWD control module
2.
AWD control module harness con-
nector
: Vehicle front
: N·m (kg-m, in-lb)
JSDIA2374GB
DLN-92
< REMOVAL AND INSTALLATION >
[TRANSFER: TY21B]
AWD CONTROL MODULE
1. Align the securing holes (A) of bracket as shown in the figure
and temporarily tighten mounting bolts.
2. When replace AWD control module, hold AWD control module
and remove protector paper on the adhesion area of bracket to
bond to the front floor (LH).
3. Tighten mounting bolts to the specified torque.
• When replacing AWD control module, perform writing unit parame-
ter. Refer to
: Vehicle front
JSDIA2375ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст