Volvo XC60 (2019 year). Manual — part 26
STARTING AND DRIVING
* Option/accessory.
436
ECO drive mode
The Eco drive mode optimizes the vehicle's driv-
ing characteristics for more fuel-efficient and
eco-friendly driving.
Use this mode to save fuel and promote eco-
friendly driving.
When ECO mode is activated, the following cha-
racteristics are modified:
•
The automatic transmission's shifting points.
•
Engine control and accelerator pedal
response.
•
Eco Coast functionality is activated and
engine braking is disabled when the acceler-
ator pedal is released at speeds between
65 and 140 km/h (40 and 87 mph).
•
Some of the climate system settings will be
reduced or switched off.
•
The suspension's self-leveling function* will
lower ground clearance to help reduce wind
resistance.
•
Information will be shown in the ECO gauge
in the instrument panel to help promote
more eco-friendly and economical driving.
Coast function Eco Coast
Eco Coast essentially deactivates engine braking,
allowing the vehicle's kinetic energy to be used
to roll greater distances. When the driver releases
the accelerator pedal, the transmission is auto-
matically disengaged from the engine. Engine
speed is reduced to idling speed to reduce fuel
consumption.
This function is most effective in driving situa-
tions where the vehicle can roll freely for a long
distance, e.g. on roads with slight downgrades or
when a decrease in speed is anticipated, such as
when approaching an area with a lower speed
limit.
Activating Eco Coast
The function is activated when the accelerator
pedal is fully released and the following condi-
tions are met:
•
Eco drive mode is activated.
•
The gear selector is in D.
•
The vehicle's speed is approximately
65-140 km/h (40-87 mph).
•
The gradient of the downgrade is less than
approximately 6%.
COASTING will be displayed in the instrument
panel when Eco Coast is being used.
Limitations
Eco Coast is not available if:
•
The engine and/or transmission are not at
normal working temperatures.
•
The gear selector is moved from D to manual
shifting mode.
•
The vehicle's speed is not within the
65-140 km/h (40-87 mph) range.
•
The gradient of the downgrade is more than
approximately 6%.
•
The steering wheel paddles* are being used
for manual shifting.
Deactivating and turning off Eco Coast
In certain situations, it may be advisable to deac-
tivate or turn off Eco Coast so that engine brak-
ing can be used. These situations might include
driving down steep hills or before passing
another vehicle to help ensure this can be done
as safely as possible.
Deactivate Eco Coast by:
•
Pressing the accelerator or brake pedal.
•
Moving the gear selector to manual mode.
•
Using the steering wheel paddles* to shift.
Turn off Eco Coast by:
•
Switching drive mode* or switching off drive
mode Eco in Function view.
It is possible to roll short distances even without
Eco Coast in order to help conserve fuel. How-
ever, for the best fuel economy, Eco Coast should
be activated and used to roll longer distances.
Cruise control Eco Cruise
When cruise control is activated in the Eco drive
mode, the vehicle's acceleration and deceleration
will be slower than in other drive modes to help
further conserve fuel. Because of this, the vehi-
cle's actual speed may be slightly above or below
the set speed.
STARTING AND DRIVING
* Option/accessory.
437
•
On a level road, the vehicle's actual speed
may differ from the set speed when cruise
control is active and the vehicle is coasting.
•
On a steep uphill gradient, the vehicle's
speed is reduced until the transmission
downshifts. Reduced acceleration is then ini-
tiated in order to reach the set speed.
•
On a downhill gradient in which the vehicle is
coasting, the vehicle's actual speed may be
slightly above or below the set speed. The
function uses engine braking to keep the set
speed. If necessary, the normal brakes are
also applied.
ECO gauge in the instrument panel
Eco gauge in 12" instrument panel*.
Eco gauge in 8" instrument panel.
The ECO gauge indicates how economical cur-
rent driving is:
•
A low reading in the green area of the gauge
indicates economical driving.
•
A high reading is shown when driving is not
economical, e.g. heavy braking or rapid accel-
eration.
The ECO gauge also has an indicator showing
how a reference driver would drive in the same
driving situation. This is shown by the short
pointer in the gauge.
ECO Climate
In Eco mode, ECO climate is automatically acti-
vated in the passenger compartment to help
reduce energy consumption.
When the ECO function is activated, settings
for certain climate system and electricity con-
suming functions are reduced. Some of these
settings can be reset manually, but full func-
tionality will only be restored by switching off
the ECO function or adapting the
Individual
*
drive mode to full climate system functionality.
If condensation forms on the windows, tap the
max defroster button, which will function normally.
Related information
•
•
Activating and deactivating ECO drive mode
using the function button (p. 438)
•
•
•
STARTING AND DRIVING
* Option/accessory.
438
Activating and deactivating ECO
drive mode using the function
button
There is a function button for Eco drive mode in
the center display's Function view if the vehicle
is not equipped with a drive mode control in the
tunnel console.
When the engine is switched off, ECO mode is
deactivated and must therefore be reactivated
each time the engine is started. ECO will be dis-
played in the instrument panel when the function
is activated.
Selecting Eco drive mode in the center
display's Function view
–
Tap the
Driving Mode ECO
button to acti-
vate or deactivate the function.
> An indicator light in the button will illumi-
nate when the function is activated.
Related information
•
•
•
Start/Stop function
Start/Stop is a function that temporarily switches
off the engine when the vehicle has stopped,
e.g. at a traffic light or in heavy traffic, and then
starts it again automatically when the brake
pedal is released.
The Start/Stop function reduces fuel consump-
tion, which helps to reduce exhaust emissions.
The system makes it possible to drive more eco-
nomically and climate-smart by letting the engine
auto-stop when appropriate.
Related information
•
Driving with the Start/Stop function (p. 438)
•
Conditions for the Start/Stop function
(p. 440)
•
Driving with the Start/Stop function
Start/Stop is a function that temporarily turns off
the engine when the vehicle is stationary and
then automatically starts it again when the vehi-
cle starts moving.
The Start/Stop function is available when the
ignition is started and can be activated if certain
conditions are met. The instrument panel indi-
cates if the function is available, active or not
available.
All of the vehicle's ordinary systems, such as
lighting, radio, etc. function normally when the
engine has been auto-stopped. Certain functions
may be temporarily reduced, however, such as
the climate system's blower speed or extremely
high audio system volume.
Auto-stop
To auto-stop the engine:
•
Stop the vehicle by applying the brakes and
keep the brake pedal depressed. The engine
will auto-stop.
In Eco or Comfort
5
drive mode, the engine may
auto-stop before the vehicle has completely stop-
ped.
With Adaptive Cruise Control or Pilot Assist acti-
vated, the engine will auto-stop after approxi-
mately three seconds.
5
Normal start mode.
STARTING AND DRIVING
* Option/accessory.
439
Auto-start
The following conditions must be met for the
engine to auto-start.
•
Release the brake pedal. The engine will
auto-start and the vehicle can be driven. On
an uphill gradient, Hill Start Assist (HSA) will
activate to help prevent the vehicle from roll-
ing backward.
•
When Auto-hold is activated, auto-start will
be delayed until the accelerator is pressed.
•
When Adaptive Cruise Control or Pilot Assist
are activated, the engine will auto-start when
the accelerator pedal is depressed or the
button on the left-side steering wheel
keypad is pressed.
•
Maintain pressure on the brake pedal and
press the accelerator pedal. The engine will
auto-start.
•
On a downhill gradient: Release the brake
pedal slightly so that the vehicle begins to
roll. The engine will auto-start after a slight
increase in speed.
Symbols in the instrument panel
12" instrument panel*
•
READY will be displayed in the tachometer
when Start/Stop is available.
•
An indicator in the tachometer will point
toward READY when Start/Stop is active
and the engine has auto-stopped.
•
READY will be grayed-out when Start/Stop
is not available.
•
No message will be shown when the func-
tion is turned off.
The function is active and the engine has auto-stopped.
8" instrument panel
The symbol is displayed at the bottom of the
speedometer.
Symbol
Meaning
White symbol: the function is avail-
able.
Beige symbol: The function is
active and the engine has auto-
stopped.
Symbol
Meaning
the function is not available
because the conditions have not
been met.
No symbol will be shown when the
function is turned off.
Related information
•
Temporarily deactivating the Start/Stop func-
tion (p. 440)
•
Conditions for the Start/Stop function
(p. 440)
•
•
•
STARTING AND DRIVING
440
Temporarily deactivating the Start/
Stop function
In certain situations, it may be advisable to tem-
porarily turn the Start/Stop function off.
To turn off Start/Stop, tap the
Start/Stop
function button in
the center display's Function
view. The indicator light in the
button will go out when the
function has been turned off.
The function will remain turned off until:
•
it is reactivated
•
the drive mode is changed to Eco.
Related information
•
Driving with the Start/Stop function (p. 438)
•
Conditions for the Start/Stop function
(p. 440)
Conditions for the Start/Stop
function
Certain conditions must be met for Start/Stop to
function.
If any condition is not met, this will be indicated in
the instrument panel.
The engine does not auto-stop
The engine will not auto-stop if:
•
the vehicle has not reached a speed of
ca 10 km/h (6 mph) after starting.
•
after several auto-stops, the speed must
again exceed approximately ca 10 km/h
(6 mph) before the next auto-stop.
•
the driver's seat belt is unbuckled.
•
the start battery's charge is below the mini-
mum level.
•
the engine is not running at its normal oper-
ating temperature.
•
the ambient temperature is under approxi-
mately -5 °C (23 °F) or over approximately
30 °C (86 °F).
•
windshield heating is activated.
•
the climate system settings and the actual
climate in the passenger compartment differ.
•
the vehicle is backing up.
•
the start battery's temperature is above or
below the permitted limits.
•
the driver is turning the steering wheel hard.
•
the road gradient is very steep.
•
the hood is open.
•
driving at high altitude and the engine has
not reached its normal operating tempera-
ture.
•
ABS has been activated.
•
hard braking (even if the ABS system has
not been activated).
•
many starts during a short period of time
have triggered the starter motor's overheat-
ing protection.
•
a trailer's electrical system is connected to
the vehicle's electrical system.
•
the transmission is not running at its normal
operating temperature.
•
The gear selector is in mode M (
±).
The engine does not auto-start
The engine will not auto-start after an auto-stop
if:
•
the driver is not wearing a seat belt, the gear
selector is in the P position and the driver's
door is open. The engine must be started
normally.
The engine auto-starts while the brake
pedal is depressed
In the following situations, the engine will auto-
start even if the brake pedal is depressed:
STARTING AND DRIVING
441
•
High levels of condensation on the inside of
the windows.
•
the climate system settings and the actual
climate in the passenger compartment differ.
•
Electrical current consumption is temporarily
high or the start battery's charge is below the
minimum level.
•
The brake pedal is pumped repeatedly.
•
The hood is open.
•
The vehicle begins to roll or increases speed
slightly if the engine auto-stopped before the
vehicle was at a standstill.
•
The driver's seat belt is unbuckled with the
gear selector in the D or N positions.
•
The gear selector is moved from D to R or M
(
±).
•
The driver's door is opened with the gear
selector in D. An audible signal and a text
message informs the driver that the ignition
is on.
WARNING
Do not open the hood if the engine has auto-
stopped. Turn off the engine by switching off
the ignition before lifting the hood.
Related information
•
•
Driving with the Start/Stop function (p. 438)
•
STARTING AND DRIVING
* Option/accessory.
442
Leveling control* and suspension
The vehicle's leveling control system adjusts the
suspension and shock absorbers automatically
to help provide good comfort and control while
driving. Leveling can also be controlled manually
to facilitate loading or getting in and out of the
vehicle.
Pneumatic suspension and shock
absorbers
The system is adapted to the selected drive
mode and vehicle speed. The pneumatic suspen-
sion reduces the vehicle's ground clearance at
higher speeds to reduce air resistance and
increase stability. The shock absorbers are nor-
mally set to provide the best possible comfort
and are adjusted continuously according to the
road surface and the vehicle's acceleration, brak-
ing and cornering.
The instrument panel indicates
when the suspension level is
being adjusted.
The following apply if a door or the tailgate is
opened:
•
If a door is opened, the level can only be
adjusted upwards.
•
If the tailgate is open, the level can only be
adjusted downwards.
Parking
When parking, make sure that there is adequate
space above and below the vehicle since ground
clearance may vary depending on e.g. ambient
temperature, how the vehicle is loaded, if loading
mode is used, which drive mode is selected after
the engine is started, etc.
The level may also be adjusted a period after the
vehicle is parked. This is to compensate for any
height changes that may occur due to tempera-
ture changes in the air springs when the vehicle
cools.
Transporting
When transporting the vehicle on a ferry, train or
truck, only secure (lash) the vehicle around the
tires, not using any other parts of the chassis.
Changes in the pneumatic suspension may occur
during transport, which could adversely affect the
lashing and result in damage.
STARTING AND DRIVING
}}
443
Symbols and messages in driver display
Symbol
Message
Meaning
Suspension
Deactivated by user
Active chassis has been switched off manually by the user.
Suspension
Temporarily reduced performance
Active chassis performance has been temporarily reduced due to extensive system use. If this
message appears frequently (e.g. several times in one week) contact a workshop
A
.
Suspension
Service required
A fault has occurred. Visit a workshop
A
as soon as possible.
Suspension failure
Stop safely
A critical fault has occurred. Stop safely, have the car towed to a workshop
A
.
||
STARTING AND DRIVING
* Option/accessory.
444
Symbol
Message
Meaning
Suspension
Slow down Vehicle too high
A fault has occurred. If the message appears while driving, contact a workshop
A
.
Suspension
Auto adjusting vehicle level
Level control to target height is in progress.
A
An authorized Volvo workshop is recommended.
Related information
•
Leveling control settings* (p. 445)
•
STARTING AND DRIVING
}}
* Option/accessory.
445
Leveling control settings*
Turn off leveling control before lifting the vehicle
with a jack to help avoid problems with the
pneumatic suspension.
The vehicle can be lowered or raised to make it
easier to load or for passengers to get in and
out.
Adjusting loading mode
Use the buttons in the cargo compartment to
raise or lower the rear section of the vehicle to
facilitate loading or unloading the vehicle or con-
necting or disconnecting a trailer.
Center display settings
Easy Entry and Exit Suspension Control
The vehicle can be lowered to make it easier to
get in and out.
Activating easy entry in the center display:
1. Tap
Settings
in the Top view.
2. Tap
My Car
Mirrors and Convenience
.
3. Select
Easy Entry and Exit Suspension
Control
.
> When the vehicle is parked and the
engine is turned off, the level is lowered.
(Level adjustment will stop if a side door
is opened and will resume after a slight
delay when the door has been closed.)
When the engine is started and the vehi-
cle begins to move, the level will be raised
to the height set by the selected drive
mode.
Disable Leveling Control
In certain situations, this function must be turned
off, e.g. before the vehicle is raised using a jack*.
The level difference caused by raising the vehicle
with a jack could cause problems with the pneu-
matic suspension.
Turning off the function in the center display:
1. Tap
Settings
in the Top view.
2. Tap
My Car
Parking Brake and
Suspension
.
3. Select
Disable Leveling Control
.
Related information
•
Leveling control* and suspension (p. 442)
•
Loading recommendations (p. 577)
Low Speed Control*
The low-speed function, Low Speed Control
(LSC), facilitates and improves control and trac-
tion on rough roads and slippery surfaces, e.g.
when towing a trailer on grass or up boat ramps.
In vehicles equipped with drive mode control*,
the function is included in the Off Road drive
mode.
Low Speed Control is designed for driving on
rough roads and when towing trailers at low
speeds, up to approximately 40 km/h (25 mph).
When driving at low speeds, LSC prioritizes low
gears and all-wheel drive to help avoid wheel spin
and improve traction on all wheels. The accelera-
tor pedal will be less responsive to improve trac-
tion and speed control at low speeds.
The function is activated together with Hill
Descent Control (HDC), which makes it possible
to control speed going down steep hills using the
accelerator pedal and reduces the need to use
the brake pedal. The system makes it possible to
maintain a low and uniform speed when driving
down steep hills.
||
STARTING AND DRIVING
* Option/accessory.
446
When LSC with HDC is activated, the feel of
the accelerator pedal and engine response
will change.
This drive mode is not designed to be used
for normal street driving.
The function is deactivated when driving at
high speeds and must be reactivated at lower
speeds if so desired.
Related information
•
Activating and deactivating Low Speed Con-
trol* using the function button (p. 446)
•
•
Hill Descent Control* (p. 447)
•
All Wheel Drive (AWD)* (p. 433)
Activating and deactivating Low
Speed Control* using the function
button
There is a function button for driving at low
speeds with
Hill Descent Control
in the center
display's Function view if the vehicle is not
equipped with a drive mode control in the tunnel
console.
Selecting Low Speed Control in the
center display's Function view
–
Tap the
Hill Descent Control
button to
activate or deactivate the function.
> An indicator light in the button will illumi-
nate when the function is activated.
When the engine is switched off, the function will
be automatically deactivated.
The function is deactivated when driving at
high speeds and must be reactivated at lower
speeds if so desired.
Related information
•
•
STARTING AND DRIVING
* Option/accessory.
447
Hill Descent Control*
The function for assisting when driving downhill,
Hill Descent Control (HDC), is a low-speed
function with increased engine braking. The
function makes it possible to increase or
decrease the vehicle's speed on steep downhill
gradients by only using the accelerator pedal,
without applying the brakes.
In vehicles equipped with drive mode control*,
the function is included in the Off Road drive
mode.
HDC is designed for driving on rough roads at
low speeds and downhill gradients with slippery
or otherwise difficult road surfaces. The driver
does not need to use the brake pedal but can
instead focus on steering.
WARNING
HDC is only intended to be a supplementary
braking aid and it does not function in all sit-
uations.
The driver is always ultimately responsible for
operating the vehicle in a safe manner.
Function
Hill Descent Control allows the vehicle to move
forward or backward at very low speeds assisted
by the brake system. The driver can increase the
speed by pressing the accelerator pedal. When
the accelerator pedal is released, the vehicle will
return to very low speed regardless of how steep
the hill is and without the brakes needing to be
applied. The brake lights will illuminate when the
function is activated.
The driver can brake to stop or slow the vehicle
at any time by depressing the brake pedal.
HDC is activated along with Low Speed Control
(LSC), which facilitates and improves traction and
control on rough and slippery surfaces. The sys-
tem is intended to be used at low speeds, up to
approximately 40 km/h (25 mph).
To keep in mind when using HDC
•
If the function is switched off while driving on
a steep downhill gradient, braking effect will
be gradually reduced.
•
HDC can be used in gear positions D and R,
and in manual gears 1 or 2.
•
It is not possible to manually shift to third
gear or higher when HDC is active.
When LSC with HDC is activated, the feel of
the accelerator pedal and engine response
will change.
This drive mode is not designed to be used
for normal street driving.
The function is deactivated when driving at
high speeds and must be reactivated at lower
speeds if so desired.
Related information
•
Activating and deactivating Hill Descent Con-
trol* using the function button (p. 448)
•
•
•
STARTING AND DRIVING
* Option/accessory.
448
Activating and deactivating Hill
Descent Control* using the function
button
There is a function button for assistance on
steep gradients with
Hill Descent Control
in
the center display's Function view if the vehicle
is not equipped with a drive mode control in the
tunnel console.
Selecting Hill Descent Control in the
center display's Function view
HDC only works at low speeds.
–
Tap the
Hill Descent Control
button to
activate or deactivate the function.
> An indicator light in the button will illumi-
nate when the function is activated.
When the engine is switched off, the function will
be automatically deactivated.
The function is deactivated when driving at
high speeds and must be reactivated at lower
speeds if so desired.
Related information
•
Hill Descent Control* (p. 447)
•
Economical driving
Drive economically and more environmentally
conscious by thinking ahead, avoiding rapid
starts and stops and adapting driving style and
speed to the current traffic conditions.
Observe the following rules:
•
For lower fuel consumption, activate Eco
drive mode.
•
Use the Eco Coast function in drive mode
Eco - engine braking is deactivated, allowing
the vehicle's kinetic energy to be used to roll
greater distances.
•
Use gear D as often as possible and avoid
using the kick-down function.
•
For manual gear shifting, use the highest
possible gear for the current traffic situation
and road conditions - fuel consumption is
reduced at lower engine speeds (rpm). Use
the gear indicator
6
.
•
Maintain a steady speed and a generous fol-
lowing distance to traffic ahead to minimize
braking.
•
Fuel consumption is increased at high
speeds - air resistance increases with speed.
•
The trip computer's current fuel consumption
indicator can help promote more fuel-effi-
cient driving.
6
Certain markets only.
STARTING AND DRIVING
}}
449
•
Do not warm up the engine by idling. It is
better to begin driving normally immediately
after starting the engine. A cold engine uses
more fuel than a warm engine.
•
Whenever possible, avoid using the vehicle to
drive short distances. The engine does not
have time to reach a normal operating tem-
perature and this leads to increased fuel
consumption.
•
Use engine braking to brake the vehicle,
when this is safe for other road users.
•
Maintain the correct pressure in the tires and
check pressure regularly.
•
The type of tires used could affect fuel con-
sumption - consult a retailer for advice on
suitable tires.
•
Remove unnecessary items from the vehicle
- the heavier the load, the higher the fuel
consumption.
•
Roof loads increase air resistance and
increase fuel consumption. Remove roof
boxes, ski racks, etc. that are not in use.
•
Avoid driving with the windows open.
WARNING
Never turn off the engine while the vehicle is
moving, e.g. when driving downhill. This deac-
tivates certain important systems such as
power steering and brakes.
Other factors that decrease fuel
consumption
•
Dirty air cleaner.
•
Dirty engine oil and clogged oil filter.
•
Incorrect front-end alignment.
•
Incorrect wheel alignment.
Some of the above items and others are checked
as part of Volvo's standard maintenance sched-
ule.
Related information
•
‒ purer driving pleasure (p. 27)
•
•
Checking tire pressure (p. 545)
Preparing for a long trip
It is important to have the vehicle's systems and
equipment checked carefully before driving long
distances.
Check that:
•
the engine is running properly and that fuel
consumption is normal
•
there are no leaks (fuel, oil or other fluid)
•
the brake pedal is functioning optimally
•
all lights are working
‒ adjust the headlight
height if the vehicle is carrying a heavy load
•
tire tread depth and air pressure are at cor-
rect levels. Change to snow tires when driv-
ing in areas where there is a risk of snowy or
icy roads
•
the start battery is sufficiently charged
•
the wiper blades are in good condition
Related information
•
Checking tire pressure (p. 545)
•
•
•
•
Vehicle modem settings (p. 523)
•
Loading recommendations (p. 577)
•
Driving with a trailer (p. 460)
•
STARTING AND DRIVING
450
•
•
Winter driving
It is important to check the vehicle before driving
in cold/snowy conditions to make sure it can be
driven safely.
Before the cold season arrives:
•
Make sure the engine coolant contains 50%
antifreeze. This mixture helps protect the
engine from frost erosion down to
approx. -35 °C (-31 °F). Do not mix different
types of antifreeze as this could pose a
health risk.
•
Keep the fuel tank well filled to prevent con-
densation from forming.
•
Check the viscosity of the engine oil. Oil with
low viscosity (thinner oil) improves cold-
weather starting and reduces fuel consump-
tion when driving with a cold engine.
Low-viscosity oil should not be used with hard
driving or in hot weather.
•
Check the condition and charge level of the
start battery. Cold weather places greater
demands on the start battery and reduces its
capacity.
•
Use washer fluid containing antifreeze to
help prevent ice from forming in the washer
fluid reservoir.
Slippery driving conditions
For optimal traction and roadholding, Volvo rec-
ommends using snow tires on all wheels when-
ever there is a risk of snow or ice on the road.
Certain countries require use of winter tires
by law. Not all countries permit the use of
studded tires.
Practice driving on slippery surfaces under con-
trolled conditions to learn how the vehicle reacts.
Related information
•
•
•
Braking on salted roads (p. 420)
•
•
•
•
Replacing windshield wiper blades (p. 643)
•
Changing rear window wipers (p. 642)
•
STARTING AND DRIVING
* Option/accessory.
451
Driving through standing water
Driving the vehicle through a deep pool of stand-
ing water on a water-covered roadway is called
fording. This must be done with great caution.
The vehicle can be driven through water up to a
depth of 40 cm (15 in) at no more than walking
speed. Be particularly careful when driving
through flowing water.
When driving through standing water, drive slowly
and do not stop the vehicle. When you have
passed the water, press lightly on the brake pedal
and check that the brakes are functioning prop-
erly. Water, mud, slush, etc. can make the brake
linings slippery, resulting in delayed braking
effect.
•
If the vehicle is equipped with contacts for an
electric heater or trailer coupling, clean these
after driving in water or mud.
•
Do not allow the vehicle to stand in water up
to the sills any longer than absolutely neces-
sary. This could result in electrical malfunc-
tions.
•
Engine damage could occur if water
enters the air cleaner.
•
If water enters the transmission, the lubri-
cating ability of the oils is reduced and
the service life of these systems is short-
ened.
•
Damage to any component, engine,
transmission, turbocharger, differential or
its internal components caused by flood-
ing, vapor lock or insufficient oil is not
covered under warranty.
•
If the engine stalls while the vehicle is in
water, do not attempt to restart it. Have
the vehicle towed out of the water to a
workshop. An authorized Volvo workshop
is recommended. Risk of engine failure.
Because it can be difficult to determine the
water depth, avoid driving through standing or
running water.
Related information
•
•
Opening/closing the fuel filler door
The vehicle must be unlocked before the fuel
filler door can be opened
7
.
An arrow next to the fuel pump
symbol in the instrument panel
indicates the side of the vehicle
on which the fuel filler door is
located.
1. Open the fuel filler door by pressing lightly
on its rear edge.
2. After refueling, press the fuel filler door
lightly to close it.
Related information
•
7
Only locking and unlocking using the remote key, Passive Entry or Volvo On Call will affect the status of the fuel filler door.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст