Volvo V60 Cross Country (2018 year). Manual — part 11
DRIVER SUPPORT
* Option/accessory.
179
Road Sign Information (RSI) –
operation
Speed limit information
When RSI registers a road sign showing the
speed limit, this sign is displayed as a symbol on
the instrument panel.
A speed limit or a limited access road
ends
1
In situations where RSI detects a sign indicating
the end of a particular speed limit or other indi-
rect speed limit-related information (e.g., Freeway
ends, Expressway ends, etc.) this information will
be displayed in the instrument panel for approx.
10 seconds, after which no road sign information
will be shown until the next speed limit-related
sign has been detected.
Settings in MY CAR
Possible settings in MY CAR
Displaying the speed limit indication can be
deactivated. To do so:
•
Deselect the alternative in MY CAR
Settings
Car settings
Road Sign Information
or cancel by pressing EXIT.
Speed alert
The driver can opt to be alerted if the vehicle
exceeds the posted speed limit by more than
3 mph (5 km/h). The alert is given when the sym-
bol with the posted speed limit in the instrument
panel begins to flash.
To activate speed alert:
•
Check the Speed alert box in MY CAR
Settings
Car settings
Speed alert
or
cancel by pressing EXIT.
Sensus Navigation
If the vehicle is equipped with Sensus Navigation,
speed-related information is gathered from this
system if:
•
The speed limit previously detected by RSI is
no longer considered valid and no new speed
limit sign has been detected.
Related information
•
•
Road Sign Information (RSI) – limitations
(p. 180)
•
1
This function may not be available in all markets.
DRIVER SUPPORT
* Option/accessory.
180
Road Sign Information (RSI) –
limitations
RSI's camera has the same limitations as the
human eye. See The camera’s limitations
(p. 217) for more information about the camera's
limitations.
Signs that indirectly indicate the speed limit
(such as a sign with a town's name and the per-
mitted speed limit) will not be registered by RSI.
Other factors that may interfere with RSI include:
•
Faded signs
•
Signs located in a curve
•
Twisted or damaged signs
•
Signs place high above the road
•
Signs that are partially hidden/poorly placed
•
Obstructed signs
•
Signs that are partially covered by snow, ice,
etc.
•
Map information that is not up-to-date, inac-
curate or does not contain speed limit infor-
mation
2
Related information
•
•
Road Sign Information (RSI) – operation
(p. 179)
•
The camera’s limitations (p. 217)
Cruise control (CC) – introduction
Cruise control is designed to assist the driver by
maintaining a set speed. It is primarily intended
for use on long straight roads in steady traffic,
such as on highways and other main roads.
Operation
Steering wheel-mounted controls and display
Standby mode
Resume set speed
Deactivating
Activate/set speed
Selected speed (gray symbol indicates
standby mode)
Cruise control active: white symbol (gray
symbol indicates standby mode)
2
Vehicles equipped with the optional navigation system.
DRIVER SUPPORT
}}
181
Related information
•
Cruise control (CC) – engaging and setting
speed (p. 181)
•
Cruise control (CC) – deactivating (p. 183)
Cruise control (CC) – engaging and
setting speed
Cruise control is designed to assist the driver by
maintaining a set speed. It is primarily intended
for use on long straight roads in steady traffic,
such as on highways and other main roads.
Engaging the cruise control function
Steering wheel-mounted controls and display
Standby mode
Resume set speed
Deactivating
Activate/set speed
Selected speed (gray symbol indicates
standby mode)
Cruise control active: white symbol (gray
symbol indicates standby mode)
Before a speed can be set, the cruise control
system must be engaged (put in standby mode).
–
Press the CRUISE button (1).
> The symbol illuminates and the text
(---) mph
(5) indicates that cruise control
is in standby mode.
Putting cruise control in standby mode does
not set a cruising speed.
Setting a speed
Use the
or
buttons set the vehicle's cur-
rent speed. The set speed is shown in the display.
Cruise control cannot be engaged at speeds
below 20 mph (30 km/h).
Adjusting the set speed
After a speed has been set, it can be increased
or decreased by using the
or
buttons.
1. Press
or
briefly and release the but-
ton to increase or decrease vehicle speed by
approximately 1 mph or 1 km/h.
> This will become the set speed when the
button is released.
||
DRIVER SUPPORT
182
2. Press and hold one of these buttons to
increase/decrease the speed in 1-mph or 1-
km/h increments. Release the button when
you have reached the desired speed.
•
A temporary increase in speed by press-
ing the accelerator pedal, for less than
1 minute (e.g. when passing another car),
does not affect the current cruise control
setting. The vehicle will automatically
return to the previously set speed when
the accelerator pedal is released.
•
If one of the cruise control buttons is
kept depressed for more than approx.
1 minute cruise control is disengaged.
The engine must then be switched off in
order to reset cruise control.
Related information
•
Cruise control (CC) – introduction (p. 180)
•
Cruise control (CC) – deactivating (p. 183)
Toggling between ACC and CC
(standard Cruise Control)
Adaptive Cruise Control (ACC) helps the driver
maintain a safe distance/time interval to the vehi-
cle ahead.
Switching from ACC to CC
This may be useful if, for example, the radar sen-
sor is obstructed in some way. See Adaptive
Cruise Control – limitations (p. 193) for addi-
tional information.
•
Press and hold the
button; the symbol in
the instrument panel will switch from
to
.
>
This activates the standard cruise control
function (see Cruise control (CC) – introduc-
tion (p. 180)).
WARNING
Switching from ACC to CC means that:
•
Your vehicle will no longer automatically
maintain a set distance to a vehicle
ahead.
•
Only the set speed will be maintained and
the driver will have to apply the brakes
when needed.
Switching from CC to ACC
Switch off cruise control by pressing
once or
twice as needed according to the instructions in
the previous section "Turning ACC off com-
pletely." The next time the system is switched on,
ACC will be reactivated.
Related information
•
Adaptive Cruise Control – introduction
(p. 183)
•
DRIVER SUPPORT
}}
183
Cruise control (CC) – deactivating
Cruise control is designed to assist the driver by
maintaining a set speed. It is primarily intended
for use on long straight roads in steady traffic,
such as on highways and other main roads.
Automatic deactivation
The cruise control is automatically deactivated
temporarily if one of the following occurs:
•
If the speed drops below approximately
20 mph (30 km/h).
•
When the brake pedal is depressed.
•
If the gear selector is moved to position N.
•
During wheel spin or wheel lock-up.
•
If the vehicle's speed is increased by using
the accelerator pedal for more than 1 minute.
•
Engine speed (rpm) is too high or too low.
The currently set speed will be saved in the sys-
tem's memory.
Temporary deactivation
The driver can temporarily deactivate the cruise
control by pressing 0. The saved speed is shown
in brackets in the information display.
Resume set speed
If the cruise control has been deactivated tempo-
rarily, it can be reactivated by pressing
. The
vehicle's speed returns to the most recently set
speed.
WARNING
There may be a significant increase in speed
after the
button has been pressed.
Deactivation
The Cruise control is disengaged by pressing
or by switching off the engine. The set speed is
cleared.
WARNING
Cruise control should not be used in heavy
traffic or when driving on wet or slippery
roads. Cruise control may not maintain set
speed on steep downgrades.
Related information
•
Cruise control (CC) – introduction (p. 180)
•
Cruise control (CC) – engaging and setting
speed (p. 181)
Adaptive Cruise Control –
introduction
ACC is an optional system designed to assist
the driver by maintaining a set speed or a set
time interval to the vehicle ahead. It is primarily
intended for use on long straight roads in steady
traffic, such as on highways and other main
roads.
When the driver has set the desired speed and
the time interval to the vehicle ahead, ACC func-
tions as follows:
•
If there are no other vehicles in the lane
ahead of you, your vehicle will travel at the
set speed.
•
If ACC's radar sensor detects a slower mov-
ing vehicle in the lane ahead, the system will
adapt your vehicle's speed to help maintain
the set time interval to the vehicle ahead.
When there are no longer slower moving
vehicles ahead, your vehicle will accelerate to
resume the set speed.
If ACC is switched off completely or in standby
mode and your vehicle comes too close to
another vehicle ahead, the driver will be warned
by the Distance Alert system (see Distance Alert
– introduction (p. 198)).
||
DRIVER SUPPORT
184
WARNING
•
Adaptive Cruise Control cannot cover all
driving situations and traffic, weather and
road conditions. The "Function" section
provides information about limitations that
the driver must be aware of before using
this feature.
•
This system is designed to be a supple-
mentary driving aid. It is not, however,
intended to replace the driver's attention
and judgement. The driver is responsible
for maintaining a safe distance and speed
and must intervene if Adaptive Cruise
Control does not maintain a suitable
speed or suitable distance to the vehicle
ahead.
•
Maintenance of ACC components may
only be performed by a trained and quali-
fied Volvo technician.
Operation
Controls and display
Resume previous settings.
Off/On/Standby mode
Decrease/increase time interval
Put in active mode and set a speed (each
additional press increases/decreases speed
by 1 mph (approximately 2 km/h))
Set speed (shown in green when active,
shown in white when in standby mode)
Time interval
ACC active (green symbol) or in standby
mode (white symbol)
Radar sensor type approval
USA
FCC ID: L2C0038TR
Canada
IC: 3432A-0038TR
This device complies with Part 15 of the FCC
Rules and with Industry Canada license-exempt
RSS standard(s). Operation is subject to the fol-
lowing two conditions: (1) This device may not
cause harmful interference, and (2) This device
must accept any interference received, including
interference that may cause undesired operation.
The term “IC:” before the radio certification num-
ber only signifies that Industry Canada technical
specifications were met.
WARNING
Changes or modifications not expressively
approved by the party responsible for compli-
ance could void the user's authority to oper-
ate the equipment.
Related information
•
Toggling between ACC and CC (standard
Cruise Control) (p. 182)
•
Cruise control (CC) – introduction (p. 180)
•
Adaptive Cruise Control – troubleshooting
(p. 197)
•
Adaptive Cruise Control – symbols and mes-
sages (p. 195)
•
DRIVER SUPPORT
}}
185
•
Adaptive Cruise Control – setting speed
(p. 187)
•
•
Adaptive Cruise Control (ACC) – Queue
Assist (p. 191)
•
Adaptive Cruise Control – passing another
vehicle (p. 190)
•
Adaptive Cruise Control – limitations
(p. 193)
•
Adaptive Cruise Control – function (p. 185)
•
Adaptive Cruise Control – engaging (p. 187)
•
Adaptive Cruise Control – deactivating
(p. 189)
Adaptive Cruise Control – function
Function
Function overview
3
Warning light, braking by driver required
Controls in steering wheel
Radar sensor in front grille
Adaptive Cruise Control consists of:
•
A cruise control system to maintain a set
speed
•
A system to maintain a set distance to the
vehicle ahead, which is expressed as a time
interval. For example, you can choose to
remain approximately 2 seconds behind the
vehicle ahead. The actual distance required
to maintain a 2-second interval will vary
according the speed of the vehicles.
WARNING
•
Adaptive Cruise Control is not a collision
avoidance system. The driver is always
responsible for applying the brakes if the
system does not detect another vehicle.
•
Adaptive Cruise Control does not react to
people or animals, or small vehicles such
as bicycles and motorcycles. It also does
not react to slow moving, parked or
approaching vehicles, or stationary
objects.
•
Do not use Adaptive Cruise Control in
demanding driving conditions such as city
driving or other heavy traffic situations, in
slippery conditions, when there is a great
deal of water or slush on the road, during
heavy rain or snow, in poor visibility, on
winding roads or on highway on- or off-
ramps.
The distance to the vehicle ahead (in the same
lane) is monitored by a radar sensor. Your vehi-
cle's speed is regulated by accelerating and
braking. The brakes may emit a sound when they
are being modulated by the adaptive cruise con-
trol system. This is normal.
3
The illustration is generic; details will vary, depending on the model
||
DRIVER SUPPORT
* Option/accessory.
186
WARNING
The brake pedal moves when the adaptive
cruise control system modulates the brakes.
Do not rest your foot under the brake pedal.
The ACC system is designed to smoothly regu-
late speed. However, the driver must apply the
brakes in situations that require immediate brak-
ing. This applies when there are great differences
in speed between vehicles, or if the vehicle ahead
brakes suddenly.
WARNING
Due to limitations in the radar sensor, braking
may occur unexpectedly or not at all, see
Adaptive Cruise Control – limitations (p. 193).
Adaptive Cruise Control can be put in active
mode at any permitted speed. However, if the
vehicle's speed falls below 18 mph (30 km/h) or
if engine speed (rpm) becomes too low, ACC dis-
engages (goes into standby mode) and will no
longer modulate the brakes. The driver will then
have to maintain a safe distance to the vehicle
ahead.
WARNING
When Adaptive Cruise Control is in standby
mode or is switched off completely, the
brakes will not be modulated automatically.
The driver must assume full control over the
vehicle.
Warning light—driver braking required
Adaptive Cruise Control can exert brake force
that is equivalent to approximately 40% of the
vehicle's total braking capacity. In situations
requiring more brake force than ACC can provide
and if the driver does not apply the brakes, an
audible signal from the Collision Warning system
will sound and warning light will illuminate (see
Collision warning
windshield to alert the driver to react.
Strong sunlight, reflections, extreme light con-
trasts, the use of sunglasses, or if the driver is
not looking straight ahead may make the
warning symbol in the windshield difficult to
see.
WARNING
Adaptive Cruise Control only warns of vehicles
detected by the radar sensor, see Adaptive
Cruise Control – limitations (p. 193). In some
cases there may be no warning or the warn-
ing may be delayed. The driver should always
apply the brakes when necessary.
Steep inclines and/or heavy loads
ACC is primarily intended for use on fairly level
roads. The system may have difficulty maintaining
the correct distance to a vehicle ahead on steep
inclines, if the vehicle is carrying a heavy load or
is towing a trailer. In these situations, the driver
should always be prepared to apply the brakes if
necessary.
Related information
•
DRIVER SUPPORT
}}
187
Adaptive Cruise Control – engaging
Putting ACC in standby mode
Before ACC can be used to regulate speed
and/or the distance to a vehicle ahead, it must
first be put in standby mode.
To do so:
Controls and display
Off/On/Standby mode
•
Press
(2).
>
The same symbol (7) appears (in white) in
the instrument panel to indicate that ACC is
in standby mode.
The driver's door must be closed and the driv-
er's seat belt must be fastened before ACC
can be put in active mode. If the driver's seat
belt is taken off or if the driver's door is
opened, ACC will return to standby mode.
Related information
•
Adaptive Cruise Control – introduction
(p. 183)
Adaptive Cruise Control – setting
speed
Setting a speed
Once ACC has been put in standby mode:
Controls and display
Put in active mode and set a speed (each
additional press increases/decreases speed
by 1 mph (approximately 2 km/h))
•
Press
or
(4).
>
The set speed, for example 60 mph (5), will
be magnified for several seconds and the
frame around the speed will change colors
from white to green to indicate that this
speed has been stored (set).
When this symbol has changed colors
from white to green, ACC is in active
mode and the vehicle will maintain the
set speed.
||
DRIVER SUPPORT
188
This symbol indicates that you
are approaching a vehicle
ahead.
ACC will switch from maintain-
ing a set speed to maintaining
a set distance from that vehi-
cle.
When this happens, a speed
range will be indicated on the
speedometer:
The higher speed (the cur-
rently set speed (5)) will be
marked in green.
The lower speed in the range is the speed of the
vehicle ahead.
Changing the set speed
•
After a speed has been set, it can be
increased or decreased by briefly pressing
the
or
buttons. Each time one of
these buttons is pressed, the vehicle's speed
changes by 5 mph or 5 km/h. If the speed is
increased by pressing the accelerator pedal,
the vehicle's speed when the button is
pressed will be set.
•
Press and hold one of these buttons to
increase/decrease the speed in 1-mph or 1-
km/h increments. Release the button when
you have reached the desired speed.
•
If one of the Adaptive Cruise Control but-
tons is pressed for more than approxi-
mately one minute, ACC will be deacti-
vated. The engine must then be switched
off and restarted to reset ACC.
•
In some situations Adaptive Cruise Con-
trol cannot be put in active mode.
Cruise
control Unavailable
is shown in the dis-
play, see Adaptive Cruise Control – sym-
bols and messages (p. 195).
Related information
•
Adaptive Cruise Control – introduction
(p. 183)
Adaptive Cruise Control – setting
time interval
Setting a time interval
Controls and display
Decrease/increase time interval
The set time interval to vehicles ahead can be
increased by pressing
and decreased by
pressing
. The current time interval is shown
briefly in the display following adjustment.
DRIVER SUPPORT
}}
189
Different time intervals can be
selected and are shown in the
instrument panel
4
as 1–5 hori-
zontal bars. The greater the
number of bars, the longer the
time interval. One bar repre-
sents a time interval of approxi-
mately 1 second; 5 bars is approximately
3 seconds.
To set/change a time interval:
•
Press the
/
buttons (3).
At low speeds, when the distance to the vehicle
ahead is short, ACC increases the time interval
slightly. In order to follow the vehicle ahead as
smoothly as possible, ACC allows the time inter-
val to vary considerably in certain situations.
WARNING
•
Only use a time interval that is suitable in
current traffic conditions.
•
A short time interval gives the driver lim-
ited reaction time if an unexpected situa-
tion occurs in traffic.
Related information
•
Adaptive Cruise Control – introduction
(p. 183)
Adaptive Cruise Control –
deactivating
Standby mode (temporary deactivation)
To temporarily deactivate ACC (put it in standby
mode):
Controls and display
Resume previous settings.
Off/On/Standby mode
•
Press
(2).
This symbol and the marking for the set speed
with change colors from green to white.
The previously set speed and time interval are
resumed by pressing
(1).
WARNING
The vehicle may accelerate quickly after
has been pressed if its current speed is con-
siderably lower than the set speed.
Standby mode due to action by the
driver
ACC is temporarily deactivated and put in
standby mode:
•
if the brakes are applied
•
if the gear selector is moved to N
•
if the driver drives faster than the set speed
for more than 1 minute.
In this happens, the driver will have to regulate
the vehicle's speed.
If the accelerator pedal is only depressed for
a short time, such as when passing another
vehicle, ACC is deactivated temporarily and is
reactivated when the pedal is released.
Automatic standby mode
ACC is linked to other systems such as the sta-
bility system. If this system is not functioning
properly, ACC will switch off automatically.
4
The same symbol appears if Distance Alert (see Distance Alert – introduction (p. 198)) is activated
||
DRIVER SUPPORT
190
In the event of automatic deactivation, an audible
signal will sound and the message
Cruise
control Cancelled
is shown in the instrument
panel. The driver must then intervene and adapt
the vehicle's speed to the surrounding traffic and
regulate the distance to the vehicle ahead.
An automatic switch to standby mode may be
caused if:
•
engine speed (rpm) is too high/low
•
The driver's door is opened
•
The driver unbuckles his/her seat belt
•
the vehicle's speed goes below 18 mph
(30 km/h)
•
the wheels lose traction
•
brake temperature is high
•
the radar sensor is obstructed by, for exam-
ple, wet snow or rain.
Resuming the set speed
If ACC is in standby mode, it can be reactivated
by pressing the
button on the steering wheel
keypad. The vehicle will return to the most
recently set speed.
WARNING
The vehicle may accelerate quickly after
has been pressed if its current speed is con-
siderably lower than the set speed.
Turning ACC off completely
Controls and display
Resume previous settings.
Off/On/Standby mode
•
From standby mode, press (2)
once.
•
From active mode, press (2)
twice.
The set speed and time interval are then cleared
from the system's memory and cannot be
resumed by pressing (1)
.
Related information
•
Adaptive Cruise Control – introduction
(p. 183)
Adaptive Cruise Control – passing
another vehicle
Passing another vehicle
If your vehicle’s speed is being regulated by ACC
and the driver indicates that he/she would like to
pass the vehicle ahead by using the left turn sig-
nal, ACC can assist by accelerating briefly.
This function is active at speeds above approxi-
mately 45 mph (70 km/h).
WARNING
Please be aware that this function will also
cause the vehicle to accelerate briefly in cer-
tain situations other than passing another
vehicle, for example using the left turn signal
to indicate a lane change or a turn toward a
highway exit at speeds above approximately
45 mph (70 km/h).
Related information
•
DRIVER SUPPORT
}}
191
Adaptive Cruise Control (ACC) –
Queue Assist
Queue Assist is an added ACC feature that is
linked to your vehicle's automatic transmission.
Introduction
Queue Assist is an added ACC feature that is
linked to your vehicle's automatic transmission.
Queue Assist consists of the following functions:
•
Enhanced speed interval (including when the
vehicle is at a complete stop or is moving at
speed below 18 mph (30 km/h))
•
Automatic standby mode when ACC changes
target vehicles
•
No automatic braking when at a standstill
•
The parking brake is applied automatically
Please note that the lowest speed that can be
set is 18 mph (30 km/h), although ACC can
maintain a set speed/distance to a vehicle ahead
down to a standstill. Queue Assist consists of the
following features:
Enhanced speed interval
The driver's door must be closed and the driv-
er's seat belt must be fastened before ACC
can be put in active mode. If the driver's seat
belt is taken off or if the driver's door is
opened, ACC will return to standby mode.
Your vehicle can maintain the set time interval to
the vehicle ahead at any permissible speed,
including a complete stop.
In order to activate ACC at speeds below 18 mph
(30 km/h):
•
The vehicle ahead must be within a reasona-
ble distance (not farther away than approx.
100 ft/30 meters)
•
The lowest speed that can be selected is
18 mph (30 km/h), although ACC will also
help maintain the set time interval to the
vehicle ahead at lower speeds, including a
complete stop.
During short stops (less than approximately
3 seconds) in slow-moving traffic, your vehicle
will begin moving again automatically as soon as
the vehicle ahead begins to move.
If it takes more than 3 seconds for the vehicle
ahead to begin moving, ACC will be automatically
go into standby mode.
The driver will then have to reactivate ACC in one
of the following ways:
•
By pressing
•
By accelerating up to at least 3 mph
(4 km/h). ACC will then resume following the
vehicle ahead.
Your vehicle will then resume following the vehi-
cle ahead at the set time interval.
ACC can remain active and keep your vehicle
at a standstill for up to 4 minutes. After
4 minutes have elapsed, the parking brake
will be engaged and ACC will go into standby
mode.
To reactivate ACC, the driver must release the
parking brake (see Parking brake – general
information (p. 280)).
||
DRIVER SUPPORT
192
Automatic standby mode when ACC
changes target vehicles
If the vehicle ahead turns suddenly, there may be a sta-
tionary vehicle ahead
The following only applies at speeds below
approximately 18 mph (30 km/h):
If ACC changes target vehicles (the vehicle that
the radar sensor has detected) from a moving
vehicle to a stationary one, the system will apply
the brakes in your vehicle.
WARNING
At speeds above 18 mph (30 km/h), ACC
will not react to a stationary vehicle and apply
the brakes but will instead accelerate to the
previously set speed. The driver must actively
apply the brakes to stop the vehicle.
ACC disengages and goes into standby mode if:
•
Your vehicle's speed goes below 10 mph
(15 km/h) and ACC cannot determine if the
target object is a stationary vehicle or some
other type of object such as e.g., a speed
bump.
•
Your vehicle's speed goes below 10 mph
(15 km/h) and the vehicle ahead turns so
that ACC no longer has a target vehicle to
follow.
No automatic braking when at a
standstill
In certain situations, ACC will no longer apply the
brakes and go into standby mode while the vehi-
cle is not moving. This means that the driver will
have to apply the brakes.
This happens if:
•
The driver presses the brake pedal
•
The parking brake is activated
•
The gear selected is moved to P, N or R
•
The driver presses the
button to put ACC
in standby mode
The parking brake is applied
automatically
In certain situations, ACC will apply the parking
brake in order to continue keeping the vehicle at
a standstill.
This happens if:
•
The driver opens the door or takes off
his/her seat belt
•
The stability system is put in Sport mode
(see Stability system – operation (p. 175))
•
ACC has kept the vehicle at a standstill for
more than 2 minutes
•
The engine has been switched off
•
The brakes have overheated
Related information
•
DRIVER SUPPORT
}}
193
Radar sensor
The radar sensor is designed to help detect cars
or larger vehicles driving in the same direction as
your vehicle, in the same lane.
The radar sensor and its limitations
In addition to being used by the Adaptive Cruise
Control (ACC), the radar sensor is also used by
Distance Alert (see Distance Alert – introduction
(p. 198)) and Collision Warning with Full Auto-
brake and Pedestrian Detection (see Collision
warning – introduction (p. 209)).
WARNING
•
If there is visible damage to the front
grille or you suspect that the radar sensor
may be damaged in any way, contact a
trained and qualified Volvo service techni-
cian as soon as possible. The radar sen-
sor may only function partially (or not at
all) if it is damaged or is not securely fas-
tened in place.
•
Accessories or other objects, such as
extra headlights, must not be installed in
front of the grille.
•
Modification of the radar sensor could
make its use illegal.
The radar sensor's capacity to detect vehicles
ahead is impeded:
•
if the radar sensor is obstructed and cannot
detect other vehicles, for example in heavy
rain, or if snow or other objects are obscuring
the radar sensor.
Keep the area in front of the radar sensor
clean.
•
if the speed of vehicles ahead is significantly
different from your own speed.
Related information
•
Adaptive Cruise Control – introduction
(p. 183)
•
Collision warning – introduction (p. 209)
•
Distance Alert – introduction (p. 198)
Adaptive Cruise Control –
limitations
The ACC cannot cover all driving situations and
traffic, weather and road conditions.
Situations where ACC may not function
optimally
WARNING
•
The radar sensor has a limited field of
vision. In some situations it may detect a
vehicle later than expected or not detect
other vehicles at all.
•
If ACC is not functioning properly, cruise
control will also be disabled.
||
DRIVER SUPPORT
194
Radar sensor's field of vision (shown in pink)
In certain situations, the radar sensor cannot
detect vehicles at close quarters, for example
a vehicle that suddenly enters the lane
between your vehicle and the target vehicle.
Small vehicles, such as motorcycles, or vehi-
cles not driving in the center of the lane may
remain undetected.
In curves, the radar sensor may detect the
wrong vehicle or lose sight of the target vehi-
cle.
WARNING
•
Adaptive Cruise Control cannot cover all
driving situations and traffic, weather and
road conditions. The "Function" section
provides information about limitations that
the driver must be aware of before using
this feature.
•
This system is designed to be a supple-
mentary driving aid. It is not, however,
intended to replace the driver's attention
and judgement. The driver is responsible
for maintaining a safe distance and speed
and must intervene if Adaptive Cruise
Control does not maintain a suitable
speed or suitable distance to the vehicle
ahead.
•
Maintenance of ACC components may
only be performed by a trained and quali-
fied Volvo technician.
WARNING
•
Adaptive Cruise Control is not a collision
avoidance system. The driver is always
responsible for applying the brakes if the
system does not detect another vehicle.
•
Adaptive Cruise Control does not react to
people or animals, or small vehicles such
as bicycles and motorcycles. It also does
not react to slow moving, parked or
approaching vehicles, or stationary
objects.
•
Do not use Adaptive Cruise Control in
demanding driving conditions such as city
driving or other heavy traffic situations, in
slippery conditions, when there is a great
deal of water or slush on the road, during
heavy rain or snow, in poor visibility, on
winding roads or on highway on- or off-
ramps.
Related information
•
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст