Honda CR-V (2018 year). Manual — part 7
96
uu
Indicators
u
In
strum
e
nt Pa
nel
Indicator
Name
On/Blinking
Explanation
Message
*
Road Departure
Mitigation (RDM)
Indicator
*
●
Comes on when the RDM system
shuts itself off.
- Indicator may come on temporarily when
passing through an enclosed space, such as
tunnel.
- The area around the radar sensor is
blocked by dirt, mud, etc. Stop your vehicle
in a safe place, and wipe it off with a soft
cloth.
●
Have your vehicle checked by a dealer if
the indicator does not go off even after
you cleaned the radar sensor.
2 Collision Mitigation Braking
P. 532
●
Comes on when the RDM system
shuts itself off.
●
Stays on - The temperature inside the
camera is too high.
Use the climate control system to cool
down the camera.
The system activates when the
temperature inside the camera cools
down.
* Not available on all models
97
uu
Indicators
u
Continued
In
strum
e
nt Pa
nel
Indicator
Name
On/Blinking
Explanation
Message
*
Road Departure
Mitigation
(RDM) Indicator
*
●
Comes on when the RDM system
shuts itself off.
●
Stays on - The area around the camera is
blocked by dirt, mud, etc. Stop your
vehicle in a safe place, and wipe it off with
a soft cloth.
●
Have your vehicle checked by a dealer if
the indicator and message come back on
after you cleaned the area around the
camera.
* Not available on all models
98
uu
Indicators
u
In
strum
e
nt Pa
nel
Indicator
Name
On/Blinking
Explanation
Message
*
Adaptive Cruise
Control (ACC)
with Low Speed
Follow (LSF)
Indicator
(Amber)
*
●
Comes on for a few seconds when
you set the power mode to ON,
then goes off.
●
Comes on if there is a problem
with ACC with LSF.
●
Comes on while driving - Have your
vehicle checked by a dealer.
●
Indicator may come on
temporarily when the Maximum
Load Limit is exceeded.
●
ACC with LSF has been
automatically canceled.
●
Make sure the total load is within the
Maximum Load Limit.
●
Stays on constantly - Have your vehicle
checked by a dealer.
●
Comes on if anything covers the
radar sensor cover and prevents
the sensor from detecting a
vehicle in front.
●
May come on when driving in bad
weather (rain, snow, fog, etc.)
●
ACC with LSF has been
automatically canceled.
●
When the radar sensor gets dirty, stop
your vehicle in a safe place, and wipe off
dirt using a soft cloth.
●
Have your vehicle checked by a dealer if
the indicator does not go off even after
you clean the sensor cover.
●
Comes on if the ACC with LSF is
deactivated temporarily after the
battery has been disconnected,
then re-connected.
●
Drive a short distance at more than 12
mph (20 km/h). The indicator should go
off. If it does not, have your vehicle
checked by a dealer.
* Not available on all models
99
uu
Indicators
u
Continued
In
strum
e
nt Pa
nel
Indicator
Name
On/Blinking
Explanation
Message
*
Adaptive Cruise
Control (ACC)
with Low Speed
Follow (LSF)
Indicator
(Green)
*
●
Comes on when you press the
MAIN button.
2 Adaptive Cruise Control (ACC) with
P. 481
—
●
Comes on when ACC with LSF is
in operation, but the temperature
inside the front sensor camera is
too high. ACC with LSF cancels
automatically. The beeper sounds
simultaneously.
●
Use the climate control system to cool
down the camera.
●
Goes off - The camera has been cooled
down. Pressing the MAIN button can
resume the system.
2 Adaptive Cruise Control (ACC) with
P. 481
Lane Keeping
Assist System
(LKAS) Indicator
(Amber)
*
●
Comes on for a few seconds when
you set the power mode to ON,
then goes off.
●
Comes on if there is a problem
with the LKAS.
●
Stays on constantly - Have your vehicle
checked by a dealer.
* Not available on all models
100
uu
Indicators
u
In
strum
e
nt Pa
nel
Indicator
Name
On/Blinking
Explanation
Message
*
Lane Keeping
Assist System
(LKAS) Indicator
(Green)
*
●
Comes on when you press the
MAIN button.
2 Lane Keeping Assist System (LKAS)
P. 501
—
●
Comes on when the LKAS is in
operation, or the LKAS button is
pressed, but the temperature
inside the front sensor camera is
too high. The LKAS cancels
automatically. The beeper sounds
simultaneously.
●
Use the climate control system to cool
down the camera.
●
Goes off - The camera has cooled down
and the system is working normally.
●
Comes on when the area around
the camera is blocked by dirt,
mud, etc. Stop your vehicle in a
safe place, and wipe it off with a
soft cloth.
●
May come on when driving in bad
weather (rain, snow, fog, etc.)
●
Have your vehicle checked by a dealer if
the indicator and message come back on
after you cleaned the area around the
camera.
* Not available on all models
101
uu
Indicators
u
Continued
In
strum
e
nt Pa
nel
Indicator
Name
On/Blinking
Explanation
Message
*
Collision
Mitigation
Braking
System
TM
(CMBS
TM
)
Indicator
*
●
Comes on for a few seconds when
you set the power mode to ON,
then goes off.
●
Comes on when you deactivate
the CMBS
TM
. A driver information
interface message appears for five
seconds.
●
Comes on if there is a problem
with the CMBS
TM
.
●
Stays on constantly without the
CMBS
TM
off - Have your vehicle checked
by a dealer.
2 Collision Mitigation Braking
●
Indicator may come on
temporarily when the Maximum
Load Limit is exceeded.
●
Make sure the total load is within the
Maximum Load Limit.
●
Comes on if the CMBS
TM
is
deactivated temporarily after the
battery has been disconnected,
then re-connected.
●
Drive a short distance at more than 12
mph (20 km/h). The indicator should go
off. If it does not, have your vehicle
checked by a dealer.
●
Comes on when the CMBS
TM
system shuts itself off.
●
Stays on - The area around the camera is
blocked by dirt, mud, etc. Stop your
vehicle in a safe place, and wipe it off with
a soft cloth.
●
Have your vehicle checked by a dealer if
the indicator does not go off even after
you cleaned the camera.
2 Collision Mitigation Braking
* Not available on all models
102
uu
Indicators
u
In
strum
e
nt Pa
nel
Indicator
Name
On/Blinking
Explanation
Message
*
Collision
Mitigation
Braking
System
TM
(CMBS
TM
)
Indicator
*
●
Comes on when the CMBS
TM
system shuts itself off.
●
Stays on - The temperature inside the
camera is too high. Use the climate control
system to cool down the camera. The
system activates when the temperature
inside the camera cools down.
P. 479
●
Indicator may come on temporarily when
passing through an enclosed space, such
as tunnel.
- The area around the radar sensor is blocked
by dirt, mud, etc. Stop your vehicle in a safe
place, and wipe it off with a soft cloth.
●
Have your vehicle checked by a dealer if
the indicator does not go off even after
you clean the sensor cover.
2 Collision Mitigation Braking
* Not available on all models
103
uu
Indicators
u
Information Display Warning and Information Messages
*
In
strum
e
nt Pa
nel
Information Display Warning and Information Messages
*
The following messages appear only on the information display.
Message
Condition
Explanation
●
Appears when there is a problem with the sensor on
the battery.
●
Stays on constantly - Have your vehicle checked by a
dealer.
* Not available on all models
104
uu
Indicators
u
Driver Information Interface Warning and Information Messages
*
In
strum
e
nt Pa
nel
Driver Information Interface Warning and Information Messages
*
The following messages appear only on the driver information interface. Press the
(display/information) button to see the message
again with the system message indicator on.
Message
Condition
Explanation
●
Appears if any door or the tailgate is not completely
closed.
●
Appears if any door or the tailgate is opened while
driving. The beeper sounds.
●
Goes off when all doors and the tailgate are closed.
●
Appears if there is a problem with the shutter grill,
and the radiator coolant temperature is too high.
●
Power output will be reduced, so you may not be able to
accelerate or maintain your current speed. Have your
vehicle checked by a dealer.
●
Appears when the washer fluid gets low.
●
Refill the washer fluid.
2 Refilling Window Washer Fluid P. 585
●
Appears when the scheduled maintenance is due
soon.
●
Consequently, Maintenance Due Now and
Maintenance Past Due follow.
2 Maintenance Minder Messages on the Driver
Canadian models
* Not available on all models
105
uu
Indicators
u
Driver Information Interface Warning and Information Messages
*
Continued
In
strum
e
nt Pa
nel
*1:Models with the smart entry system have an ENGINE START/STOP button instead of an ignition switch.
Message
Condition
Explanation
●
Appears when the engine coolant temperature gets
abnormally high.
2 Overheating P. 633
●
Appears when you turn the ignition switch to ON
(
w
*1
without fastening the driver's seat belt.
●
Fasten the seat belt properly before you start to drive.
●
Appears when there is a problem with the sensor on
the battery.
●
Have your vehicle checked by a dealer.
●
Appears along with the battery charging system
indicator when the battery is not charging.
●
Turn off the climate control system and rear defogger to
reduce electricity consumption.
2 If the Charging System Indicator Comes On P. 637
●
Appears if the automatic brake hold is automatically
canceled while it is in operation.
●
Immediately depress the brake pedal.
●
Appears when the automatic brake hold system is
turned off.
●
Appears when the automatic brake hold button is
pressed without wearing the driver’s seat belt.
●
Fasten the driver’s seat belt.
●
Appears when the automatic brake hold button is
pressed without depressing the brake pedal while
the automatic brake hold is in operation.
●
Press the automatic brake hold button with the brake
pedal depressed.
106
uu
Indicators
u
Driver Information Interface Warning and Information Messages
*
In
strum
e
nt Pa
nel
Message
Condition
Explanation
●
Appears when the parking brake is applied
automatically while it is in operation.
2 Automatic Brake Hold P. 528
2 Parking Brake P. 524
●
Appears when the electric parking brake switch is
pressed without depressing the brake pedal while
the electric parking brake is in operation.
●
Appears while driving - Press the electric parking
brake switch with the brake pedal depressed.
●
Appears if there is something wrong with the vehicle
while you are driving.
●
Immediately stop in a safe place.
●
Have your vehicle checked by a dealer.
●
Appears if the shift position cannot be changed to
(
P due to a problem with the vehicle.
●
Apply the parking brake once you have stopped.
●
Have your vehicle checked by a dealer.
107
uu
Indicators
u
Driver Information Interface Warning and Information Messages
*
Continued
In
strum
e
nt Pa
nel
Message
Condition
Explanation
●
Appears when you open the driver’s door while the
ignition key is in ACCESSORY
(
q.
●
Turn the ignition switch to LOCK
(
0, then remove the
key.
●
Appears when the ignition key is turned to
ACCESSORY
(
q from ON
(
w. (The driver's door is
closed.)
—
●
Appears when you open the driver’s door while the
ignition key is in LOCK
(
0.
●
Remove the key from the ignition switch.
Message
Condition
Explanation
●
Appears after you set the power mode to
ACCESSORY or ON.
●
Appears when the steering wheel is locked.
●
Move the steering wheel left and right while pressing the
ENGINE START/STOP button.
Models without smart entry system
Models with smart entry system
108
uu
Indicators
u
Driver Information Interface Warning and Information Messages
*
In
strum
e
nt Pa
nel
Message
Condition
Explanation
●
Appears if you push the ENGINE START/STOP
button to turn the engine off without the shift lever
in
(
P.
●
Move the shift lever to
(
P. The power mode changes to
VEHICLE OFF.
●
Move the shift lever to
(
P, then press the ENGINE
START/STOP button twice.
●
Appears if you push the ENGINE START/STOP
button and the parking brake is not activated or the
shift lever is in
(
N position.
●
Move the shift lever to
(
P position and start the engine.
●
Appears when the power mode is in ACCESSORY.
—
●
Appears after the driver’s door is opened when the
power mode is in ACCESSORY.
●
Press the ENGINE START/STOP button twice with your
foot off the brake pedal to change the power mode to
VEHICLE OFF (LOCK).
●
Appears when you close the door with the power
mode in ON without the smart entry remote inside
the vehicle.
●
Disappears when you bring the smart entry remote back
inside the vehicle and close the door.
2 Smart Entry Remote Reminder P. 174
●
Appears when the smart entry remote battery
becomes weak.
●
Replace the battery as soon as possible.
2 Replacing the Button Battery P. 608
U.S. models
Canadian models
109
uu
Indicators
u
Driver Information Interface Warning and Information Messages
*
Continued
In
strum
e
nt Pa
nel
Message
Condition
Explanation
●
Appears if the smart entry remote battery is too
weak to start the engine or the key is not within
operating range to start the engine.
A beeper sounds six times.
●
Bring the smart entry remote in front of the ENGINE
START/STOP button to be touched with.
2 If the Smart Entry Remote Battery is Weak P. 627
●
Appears when the starter system has a problem.
●
As a temporary measure, press and hold the ENGINE
START/STOP button for up to 15 seconds while pressing
the brake pedal and manually start the engine.
Have your vehicle checked by a dealer.
●
Appears as soon as a problem is detected in the
smart entry system or push button starting system.
●
Appears constantly - Have your vehicle checked by a
dealer.
●
Appears if the vehicle is being driven in a manner
consistent with drowsy or inattentive driving.
2 Driver Attention Monitor P. 126
U.S.
Canada
110
uu
Indicators
u
Driver Information Interface Warning and Information Messages
*
In
strum
e
nt Pa
nel
Message
Condition
Explanation
●
Appears if there is a problem with the light control
system.
●
Appears while driving - Manually turn the lights on,
and have your vehicle checked by a dealer.
●
Appears if there is a problem with the headlights.
●
Appears while driving - The headlights may not be on.
When conditions allow you to drive safely, have your
vehicle checked by a dealer as soon as possible.
Models with LED headlight
111
uu
Indicators
u
Driver Information Interface Warning and Information Messages
*
Continued
In
strum
e
nt Pa
nel
Message
Condition
Explanation
●
Appears when ACC with LSF has been
automatically canceled.
●
You can resume the set speed after the condition that
caused ACC with LSF to cancel improves. Press the RES/
+ button.
2 Adaptive Cruise Control (ACC) with Low Speed
P. 481
●
Appears when the distance between your vehicle
and the vehicle ahead of you is too close while ACC
with LSF is in operation.
●
ACC with LSF has been automatically canceled.
2 Adaptive Cruise Control (ACC) with Low Speed
P. 481
●
Appears when pressing the –/SET button while the
distance between your vehicle and the vehicle
ahead of you is too close.
●
ACC with LSF cannot be set.
2 Adaptive Cruise Control (ACC) with Low Speed
P. 481
●
Appears when the driver’s seat belt is unfastened
while your vehicle is automatically stopped by ACC
with LSF.
●
ACC with LSF has been automatically canceled.
2 Adaptive Cruise Control (ACC) with Low Speed
P. 481
●
Appears when pressing the –/SET button while the
driver’s seat belt is unfastened.
●
ACC with LSF cannot be set.
2 Adaptive Cruise Control (ACC) with Low Speed
P. 481
Models with ACC with LSF
* Not available on all models
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст