Honda Insight (2019 year). Manual — part 8
111
uu
Indicators
u
Driver Information Interface Warning and Information Messages
Continued
In
strum
e
nt Pa
nel
Message
Condition
Explanation
• Appears when the power system temperature is low. • Your vehicle has less ability to accelerate and may be
harder to start on an incline.
• Disappears once you start driving as the High Voltage
battery warms up.
• Appears when the power system temperature is
high.
• Your vehicle has less ability to accelerate and may be
harder to start on an incline.
• Park in a safe place, and cool the system down.
2 Overheating P. 631
• Appears if the power system is in diagnostic mode.
• You may notice a decrease in available power. Have
your vehicle checked by a dealer.
• Appears if there is a problem with the acoustic
vehicle alerting system.
• Have your vehicle checked by a dealer immediately.
112
uu
Indicators
u
Driver Information Interface Warning and Information Messages
In
strum
e
nt Pa
nel
Message
Condition
Explanation
• Appears when you press the fuel fill door release
button.
• The display changes to Ready when the fuel vapor
pressure inside the fuel tank is released. You can start
refueling once Ready appears.
• Appears when the vehicle is ready to be refueled.
• Appears when the high voltage battery and other
system control temperatures are too low to operate
(approx. –40°F [–40°C] or below).
• You must wait for an increase in the ambient
temperature or move the vehicle to a warmer location.
• Consult a dealer if necessary.
• Appears when the high voltage battery temperature
is too low to operate (approx. −22°F [−30°C] or
below).
• You can start the power system and use the climate
control system to warm up the interior, which will also
warm the High Voltage battery enough for you to drive
the vehicle.
113
uu
Indicators
u
Driver Information Interface Warning and Information Messages
Continued
In
strum
e
nt Pa
nel
Message
Condition
Explanation
• Appears when the high voltage battery is running
extremely low.
• Contact a dealer immediately.
114
uu
Indicators
u
Driver Information Interface Warning and Information Messages
In
strum
e
nt Pa
nel
Message
Condition
Explanation
• Appears when you failed to select EV mode or EV
mode is automatically canceled.
• The cause may be shown with the following
message:
- Battery Temperature At Limit.
- Battery Charge Too Low.
- Engine Too Cold.
- Cabin Being Heated.
- Speed Too High.
- Hard Acceleration Requested.
• EV mode is available once the condition is improved or
the cause that canceled EV mode is cleared.
• Appears when EV mode has been automatically
canceled.
• Appears if the engine needs to be started when you
press the EV button.
—
115
uu
Indicators
u
Driver Information Interface Warning and Information Messages
Continued
In
strum
e
nt Pa
nel
Message
Condition
Explanation
• Appears when you try to change the shift position
without releasing your foot off the accelerator pedal.
• Release your foot off the accelerator pedal, then select
a shift button.
• Appears when the
(
P button is pressed while the
vehicle is moving.
• Appears if you put the transmission into
(
R while
the vehicle is moving forward, or into
(
D while the
vehicle is reversing.
• Make sure that the vehicle comes to a stop before
operating the select button.
• Appears when you set the power mode to ON
without fastening the driver’s seat belt.
• Appears when you change the shift position after
(
P has been automatically selected with the driver’s
door open, the driver’s seat belt unfastened, then
the brake pedal is released.
• Fasten the seat belt properly before you start to drive.
• Appears when you try to change the shift position
without depressing the brake pedal.
• Depress the brake pedal, then select a shift button.
116
uu
Indicators
u
Driver Information Interface Warning and Information Messages
In
strum
e
nt Pa
nel
Message
Condition
Explanation
• Appears when you set the power mode to OFF while
driving.
• Immediately stop in a safe place, set the parking brake,
then restart the power system. If the message
disappears, continue driving.
• Appears if the vehicle is stopped and the driver’s seat
belt is unfastened, as there is a possibility that the
vehicle may roll.
• When the power system is ON or when you are parking
or exiting the vehicle, put the transmission into
(
P
before releasing the brake pedal.
2 Shift Operation P. 459
• Appears if you depress the accelerator pedal when
the transmission is in
(
N.
• Release the accelerator pedal. After that, depress the
brake pedal and change the transmission position.
●
Appears if the shift position is repeatedly changed
between
(
P and another position.
●
Wait awhile, then change the shift position.
●
Appears if the 12V battery is not charged enough to
make it possible to change shift positions.
●
Keep the power system on and wait awhile.
●
The battery may be nearing the end of its life.
Have it checked by a dealer.
117
uu
Indicators
u
Driver Information Interface Warning and Information Messages
Continued
In
strum
e
nt Pa
nel
Message
Condition
Explanation
• Appears for a few seconds if you have not pressed
the
(
N button long enough to initiate Neutral-Hold
mode.
2 If you want to keep the transmission in
(
N
position [car wash mode] P. 461
• Appears when you press and hold
(
N button for
more than two seconds.
• Disappears when you set the shift position to a gear
other than
(
N.
2 If you want to keep the transmission in
(
N
position [car wash mode] P. 461
118
uu
Indicators
u
Driver Information Interface Warning and Information Messages
In
strum
e
nt Pa
nel
Message
Condition
Explanation
• Appears if there is a problem with the auto high-
beam.
• Manually operate the headlight switch.
• If you are driving with the high-beam headlights when
this happens, the headlights are changed to low beams.
●
Appears when ACC with LSF has been automatically
canceled.
●
You can resume the set speed after the condition that
caused ACC with LSF to cancel improves. Press the
RES/+ button.
2 Adaptive Cruise Control (ACC) with Low Speed
●
Flashes when the system senses a likely collision with
a vehicle in front of you.
●
Take the appropriate means to prevent a collision (apply
the brakes, change lanes, etc.)
2 Collision Mitigation Braking System
P. 483
119
uu
Indicators
u
Driver Information Interface Warning and Information Messages
Continued
In
strum
e
nt Pa
nel
Message
Condition
Explanation
●
Appears when ACC with LSF is canceled due to
excessive high vehicle speed.
●
Reduce the speed, then reset ACC with LSF.
2 Adaptive Cruise Control (ACC) with Low Speed
●
Appears when the speed of the vehicle is too high for
you to set ACC with LSF.
●
Reduce the speed, then set ACC with LSF.
2 Adaptive Cruise Control (ACC) with Low Speed
●
Appears if ACC with LSF is canceled while your
vehicle is automatically stopped by ACC with LSF.
●
Immediately depress the brake pedal.
●
Appears when pressing the RES/+ or SET/− button
while the vehicle is moving and the brake pedal is
depressed.
●
ACC with LSF cannot be set.
120
uu
Indicators
u
Driver Information Interface Warning and Information Messages
In
strum
e
nt Pa
nel
Message
Condition
Explanation
●
Appears when the distance between your vehicle
and the vehicle ahead of you is too close while ACC
with LSF is in operation.
●
ACC with LSF has been automatically canceled.
2 Adaptive Cruise Control (ACC) with Low Speed
Follow (LSF) P. 492
●
Appears when pressing the RES/+ or SET/− button
while the distance between your vehicle and the
vehicle ahead of you is too close.
●
ACC with LSF cannot be set.
2 Adaptive Cruise Control (ACC) with Low Speed
Follow (LSF) P. 492
●
Appears when the parking brake is applied
automatically while ACC with LSF is in operation.
●
ACC with LSF has been automatically canceled.
2 Adaptive Cruise Control (ACC) with Low Speed
Follow (LSF) P. 492
2 Parking Brake P. 531
●
Appears when pressing the RES/+ or SET/− button
while the parking brake is applied.
●
ACC with LSF cannot be set.
2 Adaptive Cruise Control (ACC) with Low Speed
Follow (LSF) P. 492
2 Parking Brake P. 531
121
uu
Indicators
u
Driver Information Interface Warning and Information Messages
Continued
In
strum
e
nt Pa
nel
Message
Condition
Explanation
●
Appears if the VSA® or traction control function
operates while ACC with LSF is in operation.
●
ACC with LSF has been automatically canceled.
2 Adaptive Cruise Control (ACC) with Low Speed
●
Appears just before the ACC with LSF is
automatically canceled when you are descending a
long hill etc (The following interval is automatically
set to extra long).
●
Appears when the ACC with LSF has been
automatically canceled.
2 Adaptive Cruise Control (ACC) with Low Speed
●
Appears when you are descending a long hill etc and
you press the RES/+ or SET/− button.
122
uu
Indicators
u
Driver Information Interface Warning and Information Messages
In
strum
e
nt Pa
nel
Message
Condition
Explanation
●
Appears when the driver’s seat belt is unfastened
while your vehicle is automatically stopped by ACC
with LSF.
●
ACC with LSF has been automatically canceled.
2 Adaptive Cruise Control (ACC) with Low Speed
●
Appears when pressing the RES/+ or SET/− button
while the driver’s seat belt is unfastened.
●
ACC with LSF cannot be set.
2 Adaptive Cruise Control (ACC) with Low Speed
●
Appears when the transmission is put into any
position other than
(
D while ACC with LSF is in
operation.
●
ACC with LSF has been automatically canceled.
2 Adaptive Cruise Control (ACC) with Low Speed
●
Appears when pressing the RES/+ or SET/− button
while the transmission is in any position other than
(
D.
●
ACC with LSF cannot be set.
123
uu
Indicators
u
Driver Information Interface Warning and Information Messages
Continued
In
strum
e
nt Pa
nel
Message
Condition
Explanation
●
Appears when the vehicle is stopped on a very steep
slope while ACC with LSF is in operation.
●
ACC with LSF has been automatically canceled.
2 Adaptive Cruise Control (ACC) with Low Speed
Follow (LSF) P. 492
●
Appears when pressing the RES/+ or SET/− button
while the vehicle is stopped on a very steep slope.
●
ACC with LSF cannot be set.
2 Adaptive Cruise Control (ACC) with Low Speed
Follow (LSF) P. 492
124
uu
Indicators
u
Driver Information Interface Warning and Information Messages
In
strum
e
nt Pa
nel
Message
Condition
Explanation
●
Appears if anything covers the radar sensor cover
and prevents the sensor from detecting a vehicle in
front.
●
May appear when driving in bad weather (rain,
snow, fog, etc.)
●
When the radar sensor gets dirty, stop your vehicle in a
safe place, and wipe off dirt using a soft cloth.
●
Have your vehicle checked by a dealer if the message
does not disappear even after you clean the sensor
cover.
●
Appears if the temperature inside the front sensor
camera is too high and the ACC with LSF, LKAS,
traffic sign recognition system and auto high-beam
cannot be activated.
●
Use the climate control system to cool down the
camera.
●
Disappears - The camera has been cooled down and
the systems are activated normally.
2 Front Sensor Camera P. 528
●
Appears if the area around the front sensor camera is
blocked by dirt, mud, etc and be prevented from
detecting a vehicle in front.
●
May appear when driving in bad weather (rain,
snow, fog, etc.)
●
When the front window gets dirty, stop your vehicle in
a safe place, and wipe it off with a soft cloth.
●
Have your vehicle checked by a dealer if the message
does not disappear even after you cleaned the area
around the camera.
2 Front Sensor Camera P. 528
125
uu
Indicators
u
Driver Information Interface Warning and Information Messages
Continued
In
strum
e
nt Pa
nel
Message
Condition
Explanation
●
Appears when the vehicle is driving out of a detected
lane. The steering wheel vibrates rapidly.
●
Keep the vehicle within the lane you are driving.
2 Lane Keeping Assist System (LKAS) P. 509
●
Appears when the vehicle is driving out of a detected
lane.
- The steering wheel vibrates rapidly when the
vehicle is drifting out of a detected lane.
- The steering wheel vibrates rapidly when the
vehicle is drifting out of a detected lane. The system
also steers the vehicle to help you remain within
your driving lane.
●
Keep the vehicle within the lane you are driving.
2 Road Departure Mitigation (RDM) System P. 517
●
You can change the setting for the road departure
mitigation system. Narrow, Normal, Wide, and
Warning Only can be selected.
●
Appears when the vehicle is likely to drive out of a
detected lane.
The RDM system also steers the vehicle to help you
remain within your driving lane.
—
Lane Keeping Assist System (LKAS)
Road Departure Mitigation (RDM) System
When you selected Warning Only
When you selected Narrow, Normal or Wide
Road Departure Mitigation (RDM) System
When you selected Narrow
126
uu
Indicators
u
Driver Information Interface Warning and Information Messages
In
strum
e
nt Pa
nel
Message
Condition
Explanation
●
Blinks when you fail to steer the vehicle. The beeper
sounds simultaneously.
●
Operate the steering wheel to resume the LKAS.
●
Appears when the LKAS is in operation, or the LKAS
button is pressed, but there is a problem with a
system related to the LKAS. The LKAS cancels
automatically. The beeper sounds simultaneously.
●
If any other system indicators come on, such as the
VSA®, ABS and brake system, take appropriate action.
2 Indicators P. 80
●
Appears if the ECON mode or SPORT mode cannot
be changed due to certain situations, such as a
system error or adverse driving conditions.
2 ECON Mode P. 467
2 SPORT Mode P. 463
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст