Harley Davidson Sportster Models 2009. Service Repair Manual — page 54
Fails to Disarm
Correct key fob for
vehicle?
YES
NO
Does left turn signal function?
Obtain correct fob or replace fob.
Verify fob is synchronized to vehicle’s
TSSM.
YES
NO
Replace fob battery and retest.
See E.22 TSSM MAINTENANCE.
Does fob work?
See E.13 TURN SIGNAL
ERRORS: B1121, B1122,
B1141.
1
YES
NO
System OK.
Attempt to assign new
fob to TSSM and retest.
Does fob work?
YES
NO
System OK.
Replace TSSM.
Learn password and
perform set-up.
6757
6756
6755
fc01161_en
E-32 2009 Sportster Diagnostics: Appendix E TSM/TSSM (Japan/Korea)
E.13
TURN SIGNAL ERRORS: B1121, B1122, B1141
GENERAL
The turn signals will automatically cancel based on either the
speed/acceleration of the vehicle or upon turn completion. See
.
For turn signal diagnostics, refer to
Job/Time Code Values
Dealership technicians filing warranty claims should use the
job/time code values printed in bold text underneath the
appropriate repair.
sm01275
Figure E-18. TSM/TSSM
DIAGNOSTICS
TOOL NAME
PART NUMBER
HARNESS CONNECTOR TEST KIT
HD-41404-B
BREAKOUT BOX
HD-42682
Diagnostic Tips: All
•
DTCs B1121 and B1122 will illuminate the security lamp.
•
DTC B1141 will not illuminate the security lamp.
•
When the TSM/TSSM is in 4-way flasher mode, a fault on
either the left or right turn lamp output will not cause either
DTC B1121 or DTC B1122 to be set. If fault occurs on
both left and right outputs, then both DTC B1121 and DTC
B1122 will be set.
•
When the TSM/TSSM detects an over current or short to
ground condition, it will turn off the turn lamp outputs. The
outputs will be automatically reactivated once the fault is
removed.
Table E-14. Turn Signal Errors: TSM/TSSM
START WITH FLOWCHART
SYMPTOM
DTC
Cancels Erratically
Turn signals cancel erratically
N/A
DTC B1121, DTC B1122, DTC B1141, Will Not
Flash, 4-Way Flashers Inoperable (Part 1 of 6)
Turn signals will not flash, 4-way flashers inoper-
able
B1121, B1122, B1141
Will Not Cancel Upon Turn Completion
Turn signals will not cancel upon turn completion
N/A
Flash at Double Normal Rate, All Bulbs Working
Left or right turn signals flash at double the normal
rate while all bulbs are working
N/A
2009 Sportster Diagnostics: Appendix E TSM/TSSM (Japan/Korea) E-33
Star
ter
Right
F
ront
T
ur
n
Lamp
IGN
A
CCY
15A
15A
[31A]
Ignition
Switch
[7A]
[33]
BK
Batter
y
ECM
15A
15A
BE/GY
BN/GY
R/BK
R
R
R
Secur
ity
Siren
BN/GY
BK
LGN/BN
TN/GN
A
J
D
A
B
I
C
B
TN/GN
GY
GY
O
LGN/V
LGN/V
(Optional)
O/W
O/W
LGN/BN
B
A
C
B
A
C
V
V
V
BN/GY
BN
BN
BN
W/BN
W/V
W/V
BK
W/BK
BE/GY
R/BK
R/GY
R/GY
BK/R
R
R
R/BK
GN
GN
BK
BK
BK
[142B]
[142A]
[78B]
[30B]
P
o
w
er
Signal
Ground
BK
[5]
30
Amp
MAXIFUSE
B
A
GND1
P
o
w
er
tr
ain
Ground
P
oint
TN
A
CC
−
BA
TT
−
IGN
−
[78A]
2
5
10
13
28
31
2
5
10
13
28
31
I
Q
C
P
R
87
87A
30
85
86
5
4
3
2
1
ECM
[24B]
BK/R
BK
BK/R
TSM/
TSSM
[61B]
Hor
n
Switch
Headlamp
Hi/Lo
Switch
Left
Tur
n
Switch
[24A]
Left
Hand
Controls
Rear
T
ur
n
Signals
,
XL
1200N
Only
Rear
T
ur
n
Signals
,
Except
XL
1200N
Clutch
Switch
O/W
GY
W/BK
W/BN
BK/R
Right
Tur
n
Switch
Engine
Stop
Switch
Star
t
Switch
Stop
Lamp
Switch
[22A]
Right
Hand
Controls
O/W
W/V
BK/R
BK
R
Fuseb
loc
k
T
op
Vie
w
T
op
Vie
w
[119]
Accessor
ies
Lights
Ignition
Fuel
Pump
Star
tRL
Y
System
RL
Y
ECM
Batter
y
Spare
P&A
IGN
Instr
uments
Spare
I
B
A
System
Rela
y
Star
t
Rela
y
Spare
Open
[119B]
[128]
6
5
4
3
1
[142A]
BN
TN
BK
V
Left
Indicator
Neutr
al
O
Right
Indicator
BK
Batter
y
BN
V
BK
Right
Rear
T
ur
n
Lamp
Left
Rear
T
ur
n
Lamp
T
ail
Lamp
Con
v
er
ter
Module
[19B]
BK
BK
V
V
[18B]
2
5
6
2
5
6
2
5
6
1
2
1
2
3
1
2
3
4
1
2
1
2
1
2
Right
Rear
T
ur
n
Lamp
Left
Rear
T
ur
n
Lamp
[19B]
[94B]
[94A]
[19A]
BK
BK
V
BK
V/BN
V
BK
V
[18B]
[18A]
1
2
1
2
1
2
1
2
[94B]
[94A]
[19A]
[18A]
[93A]
[7B]
T
o
tail/
br
ak
e
lamp
Left
F
ront
T
ur
n
Lamp
BK
V
BK
BK
V
BN
[31B]
BK
BN
R/BK
BK
GN/O
6
5
4
3
1
3
5
6
8
12
3
5
6
8
12
BN
V
BK
2
5
6
2
5
6
2
5
6
2
5
6
[7B]
6
5
2
1
6
5
2
1
[22B]
GY
O/W
W/BN
W/BK
BK/R
INSTR
15A
G
H
BK
O
GN/O
BE/GY
W/BK
K
T
E
S
U
87
87A
30
85
86
5
4
3
2
1
BN
V
[20A]
[20B]
BK
BK
Batter
y
Red
Band
2
1
4
3
6
5
8
7
10
9
12
11
2
1
4
3
6
5
8
7
10
9
12
11
[30A]
Batter
y
Ignition
VSS/
Ser
ial
Data
Link
Neutr
al
Switch
Left
T
ur
n
F
eed
Right
T
ur
n
F
eed
Right
T
ur
n
Switch
Input
Left
T
ur
n
Switch
Input
Star
t
Rela
y
Control
Clutch
Switch
Alar
m
Signal
Ground
TN
TN
Neutr
al
Switch
[136]
System
Rela
y
Ser
ial
Data
Link
P
o
w
er
Ground
Switched
P
o
w
er
P
o
w
er
Ground
E
K
T
S
U
I
C
Q
P
R
M
O
G
H
A
B
15A
15A
15A
P
R
I
J
C
D
15A
15A
15A
M
O
G
H
A
B
15A
15A
15A
K
L
F
15A
15A
E
1
5
7
8
1
5
7
8
NO
TE:
Spares
K
and
L
are
used
for
engine
control
on
XR
only
.
em01316
Figure E-19. Turn Signal Circuit (Typical)
E-34 2009 Sportster Diagnostics: Appendix E TSM/TSSM (Japan/Korea)
Table E-15. Wire Harness Connectors
LOCATION
TYPE
DESCRIPTION
NO.
On battery strap, behind left side cover
2-place Metri-Pack, black
MAXIFUSE
[5]
Under seat
6-place Multilock
Rear lighting
[7]
Inside tail lamp lens
2-place Multilock
Left rear turn signal
[18]
Inside tail lamp lens
2-place Multilock
Right rear turn signal
[19]
Under fuel tank
12-place Molex
Console gauges/indicator lamps
[20]
Under fuel tank
6-place Molex
Right handlebar controls
[22]
Under fuel tank
8-place Molex
Left handlebar controls
[24]
Under battery
12-place Deutsch
TSM/TSSM
[30]
Under fuel tank
6-place Multilock
Front turn signals
[31]
Behind left side door
Spade terminals
Fuse block
[61B]
Under seat
36-place Packard
ECM
[78]
Inside tail lamp lens
6-place Multilock, black
Tail lamp power in
[94]
Fuse/relay block, behind left side cover
5-place Amp, spade ter-
minals
Relay/fuse block
[119]
Stater solenoid
Locking spade terminal,
white
Starter solenoid
[128]
Right side frame, beneath gear case
cover
1-place molded jumper, black
Neutral switch
[136]
Under frame
3-place Packard, black
Security siren
[142]
Under battery
4-place Deutsch, gray
TSSM antenna connector
[208]
Crankcase housing, top rear
Ring terminal
Security antenna
[209]
Diagnostic Notes: All Turn Signal
Flowcharts
Each reference number below correlates to a circled number
on the flowchart(s).
1.
Gain access to vehicle's TSM/TSSM:
a.
Remove battery. See the Service Manual for pro-
cedure.
b.
Unplug and remove TSM/TSSM from battery tray.
c.
Reroute wiring harness so TSM/TSSM may be
reconnected while removed from vehicle.
d.
Reconnect TSM/TSSM.
2.
Perform the following procedure:
a.
. Position TSM/TSSM in same orient-
ation it is mounted on vehicle. Turn Ignition Switch
on. Turn 4-way flashers on by depressing both left
and right turn signal switches simultaneously. Turn
Ignition Switch off. The 4-way flashers should continue
to flash.
b.
Tilt TSM/TSSM greater than 45 degrees to the left.
c.
Repeat step a.
d.
Tilt TSM/TSSM greater than 45 degrees to the right.
3.
To enable diagnostic mode, see
.
4.
Connect BREAKOUT BOX (Part No. HD-42682) (gray)
between TSM/TSSM connector [30A] and wiring harness
connector [30B]. See
5.
Closely inspect handlebar controls for pinched wiring.
6.
Connect gray HARNESS CONNECTOR TEST KIT (Part
No. HD-41404-B) adapters and patch cords to connector
[22] (right) or connector [24] (left).
2009 Sportster Diagnostics: Appendix E TSM/TSSM (Japan/Korea) E-35
1
2
ed01792
1.
Left 45 degrees
2.
Right 45 degrees
Figure E-20. Tilting: TSM/HFSM
E-36 2009 Sportster Diagnostics: Appendix E TSM/TSSM (Japan/Korea)
Will Not Cancel Upon Turn Completion
Is TSM/TSSM mounted properly?
YES
NO
Mount correctly.
Check if TSM/TSSM is configured for
solo or side car operation. See E.3
VEHICLE DELIVERY.
Is it proper configuration?
YES
NO
Select proper
vehicle
configuration.
Do 4-way flashers
cancel in both
directions?
YES
NO
Operate motorcycle at a speed
greater than 7 MPH (10 km/h) in a
straight line. Activate either turn
signal. Turn signals should cancel
after 20 flashes.
Do turn signals cancel?
Replace TSM/TSSM.
Perform setup and
password learn.
6773
YES
NO
Does speedometer
register vehicle
speed?
YES
Replace TSM/TSSM.
Perform password learn
and setup.
NO
Refer to 2.2 INITIAL
DIAGNOSTIC CHECK:
ODOMETER.
6773
1
2
fc01996_en
Go to Cancels
Erratically.
2009 Sportster Diagnostics: Appendix E TSM/TSSM (Japan/Korea) E-37
Cancels Erratically
Check for voltage between Breakout Box terminal 8 (gray) and
ground at Breakout Box terminal 12 (gray): with left turn signal
switch depressed, wiggle harness between TSM/TSSM and left
handlebar switches while monitoring for voltage fluctuations or
changes in turn signal flash pattern.
Check for voltage between Breakout Box terminal 7 (gray) and
ground at Breakout Box terminal 12 (gray): with right turn signal
switch depressed, wiggle harness between TSM/TSSM and right
handlebar switches while monitoring for voltage fluctuations or
changes in turn signal flash pattern.
Are voltage fluctuations present?
YES
Locate and repair
intermittent open.
NO
Check for voltage between Breakout Box terminal 8 (gray) and ground at Breakout Box terminal 12
(gray): with left turn signal switch NOT depressed, wiggle harness between TSM/TSSM and left
handlebar switches while monitoring for voltage fluctuations or turn signal activation.
Check for voltage between Breakout Box terminal 7 (gray) and ground at Breakout Box terminal 12
(gray): with right turn signal switch depressed, wiggle harness between TSM/TSSM and right
handlebar switches while monitoring for voltage fluctuations or turn signal flash pattern.
Are voltage fluctuations present?
YES
Locate and repair
intermittent short
to voltage.
Turn ignition switch OFF.
Check for continuity between Breakout Box terminal 8 (gray) and ground at Breakout Box terminal 12
(gray): with left turn signal switch depressed, wiggle harness between TSM/TSSM and left handlebar
switches.
Check for continuity between Breakout Box terminal 7 (gray) and ground at Breakout Box terminal 12
(gray): with right turn signal switch depressed, wiggle harness between TSM/TSSM and right
handlebar switches.
Is continuity present at any time?
NO
YES
NO
Locate and repair
intermittent short
to ground.
System OK. Review turn signal
cancellation function with customer. See
TURN SIGNAL FUNCTIONS under 3.1
TURN SIGNAL OVERVIEW.
4
3
fc01998_en
E-38 2009 Sportster Diagnostics: Appendix E TSM/TSSM (Japan/Korea)
DTCs B1121, B1122, and B1141, Will Not Flash, 4-Way Flashers Inoperable (Part 1 of 6)
Turn ignition switch ON.
Are turn signal lamps on continuously?
YES
NO
Check for voltage on Breakout Box terminal 5 (Gray) (left turn
signals) or terminal 6 (Gray) (right turn signals) with TSM
disconnected from Breakout Box.
Is battery voltage present?
YES
all except XL
1200N
NO
Locate and repair
short to voltage.
Replace TSM.
Learn
password and
perform setup.
Activate 4-way flashers.
Do any lamps illuminate?
YES
NO
Is Connector [30]
mated fully?
NO
YES
Place red meter lead at
terminal 1 (Gray) and
black meter lead at
terminal 12 (Gray) of
Breakout Box.
Is battery voltage
present?
Mate
connector.
NO
YES
Move red meter lead to
Breakout Box terminal 2.
Is battery voltage
present?
NO
Check for voltage at
ignition fuse.
Is battery
voltage present on both
terminals?
NO
YES
4
6790
6791
4
6792
YES
Locate and repair
open on (GY) wire
between ignition fuse
and TSM.
6793
YES
XL 1200N only
Unplug connectors [18] and
[19] at tail lamp converter
module. Check for
continuity between
terminals 12 and 6 (right
B1124) or 12 and 5 (left
B1123) of Breakout Box
(Gray).
Is continuity present?
YES
NO
YES
NO
Unplug connectors [7] at tail
lamp converter module. Check
for voltage between terminals
12 and 6 (right B1124) or 12
and 5 (left B1123) or Breakout
Box (Gray).
Is voltage present?
Locate and repair
short to voltage
between tail lamp
converter module
and turn signal.
Locate and repair short to
voltage between
connector [30] and tail
lamp converter module.
Replace tail lamp
converter module.
fc01999_en
Go to DTCs B1121, B1122, and
B1141, Will Not Flash, 4-Way
Flashers Inoperable (Part 2 of 6).
Go to DTCs B1121, B1122,
and B1141, Will Not Flash, 4-
Way Flashers Inoperable
(Part 5 of 6).
Go to DTCs B1121,
B1122, and B1141, Will
Not Flash, 4-Way
Flashers Inoperable
(Part 5 of 6).
See 4.10 NO
ECM
POWER.
2009 Sportster Diagnostics: Appendix E TSM/TSSM (Japan/Korea) E-39
DTCs B1121, B1122, and B1141, Will Not Flash, 4-Way Flashers Inoperable (Part 2 of 6)
Continued from DTCs B1121, B1122, and B1141, Will Not Flash, 4-Way Flashers Inoperable (Part 2 of 6).
Inspect bulbs on side that will not flash.
Are the bulbs OK?
YES
NO
Place jumper wire between terminals 2 and 6 of Breakout Box.
Do the right turn signals (front and rear) illuminate?
Replace bulbs
as necessary.
6796
YES
Place a jumper wire
between terminals 1 and 5
of Breakout Box.
Do the left turn signals
(front and rear) illuminate?
NO
Check for continuity between terminal 6 of Breakout Box and right
front turn lamp and also between right front lamp housing and
ground.
Is continuity present?
YES
Check for continuity between terminal 6 of
Breakout Box and right rear lamp and also
between right rear lamp housing and ground.
Is continuity present?
Ground 6797
Signal 6798
NO
Locate and repair open
between connector [30]
or ground and front lamp.
YES
NO
Check for continuity between terminal 6 of Breakout Box
and terminal 2 of connector [19A] and also between
terminal 2 of connector [19A] and ground.
Is continuity present?
YES
NO
Locate and repair open
between connector [19B]
and rear lamp.
Check for continuity between terminal 6 of Breakout Box and terminal 2 of connector
[7A] and also between terminal 6 of connector [7A] and ground.
Is continuity present?
6809
XL 1200N?
NO
YES
YES
NO
Replace TSM/TSSM.
XL 1200N?
6791
NO
YES
Locate and repair
open between
connector [30] or
ground and rear
lamp.
Ground 6797
Signal 6798
YES
NO
Replace tail lamp
converter module.
Locate and repair open between connector
[30] or ground and connector [7A].
Ground 6797
Signal 6798
Ground 6797
Signal 6798
fc02000_en
Go to DTCs B1121,
B1122, and B1141 Will
Not Flash, 4-way Flashers
Inoperable (Part 4 of 6).
Go to DTCs B1121,
B1122, and B1141 Will
Not Flash, 4-way
Flashers Inoperable
(Part 1 of 6).
Go to DTCs B1121,
B1122, and B1141
Will Not Flash, 4-way
Flashers Inoperable
(Part 3 of 6).
E-40 2009 Sportster Diagnostics: Appendix E TSM/TSSM (Japan/Korea)
DTCs B1121, B1122, and B1141, Will Not Flash, 4-Way Flashers Inoperable (Part 3 of 6)
Continued from DTCs B1121, B1122, and B1141, Will Not Flash, 4-way Flashers Inoperable (Part 2 of 6).
Check for continuity between terminal 5 of Breakout Box and left front lamp and also between left front lamp housing and ground.
Is continuity present?
YES
NO
Locate and repair open
between connector [30] or
ground and front lamp.
YES
NO
YES
Check for continuity between terminal 5 of
Breakout Box and terminal 2 of connector [18A]
and also between terminal 2 of connector {18A]
and ground.
Is continuity present?
Ground 6797
Signal 6798
NO
Check for continuity between terminal 5 of Breakout Box
and terminal 5 of connector [7A] and also between
terminal 6 of connector [7A] and ground.
Is continuity present?
YES
NO
6809
YES
NO
6791
Ground 6797
Signal 6798
Locate and repair open
between connector
[30] or ground and
connector [7A].
Ground 6797
Signal 6798
Ground 6797
Signal 6798
Check for continuity between terminal 5 of Breakout
Box and left rear lamp and also between left rear lamp
housing and ground.
Is continuity present?
Replace TSM/HFSM.
XL 1200N?
Locate and repair open
between connector [30]
or ground and rear lamp.
Locate and repair open
between connector [18B]
and rear lamp.
Replace tail lamp
converter module.
fc02001_en
2009 Sportster Diagnostics: Appendix E TSM/TSSM (Japan/Korea) E-41
DTCs B1121, B1122, and B1141, Will Not Flash, 4-Way Flashers Inoperable (Part 4 of 6)
Continued from DTCs B1121, B1122, and B1141, Will Not Flash, 4-
way Flashers Inoperable (Part 2 of 6).
Remove turn signal bulbs, Unplug connector [20]. Check for continuity
between terminals 12 and 5 (left) of Breakout Box (gray).
Is continuity present?
YES
NO
Unplug connector [31]. Check for
continuity between terminals 12 and 6
(right) or 12 and 5 (left) of Breakout Box
(gray).
Is continuity present?
NO
Locate and repair short to
ground between
connector [31] and front
turn signals.
6810
Unplug connectors [18] and [19] at tail lamp
converter module. Check for continuity
between terminals 12 and 6 (right) or 12
and 5 (left) of Breakout Box (gray).
Is continuity present?
YES
NO
YES
NO
Unplug connectors [7] at tail lamp
converter module. Check for continuity
between terminals 12 and 6 (right) or 12
and 5 (left) of Breakout Box (gray).
Is continuity present?
Locate and repair short to
ground between tail lamp
converter module and
turn signal.
Locate and repair short to
ground between
connector [30] and tail
lamp converter module.
Replace tail lamp
converter module.
YES
6810
6810
6809
fc02002_en
Go to DTCs B1121, B1122,
and B1141, Will Not Flash, 4-
way Flashers Inoperable (Part
2 of 6).
E-42 2009 Sportster Diagnostics: Appendix E TSM/TSSM (Japan/Korea)
DTCs B1121, B1122, and B1141, Will Not Flash, 4-Way Flashers Inoperable (Part 5 of 6)
Continued from
DTCs B1121, B1122, and B1141, Will Not Flash,
4-way Flashers Inoperable (Part 1 of 6).
Check resistance to ground on Breakout Box
terminal 12 (Gray).
Is resistance less than 1 ohm?
YES
Check for 12 volts at both
terminals of 15 amp battery fuse.
Is proper voltage present at
both terminals?
YES
Repair open in (BN/GY) wire
between battery fuse and TSM/
TSSM.
6806
NO
NO
1 terminal.
Repair poor
ground.
6805
Neither terminal.
Replace
Fuse.
6807
Repair open between 30 Amp
MAXIFUSE and fuse block.
6808
fc02003_en
2009 Sportster Diagnostics: Appendix E TSM/TSSM (Japan/Korea) E-43
DTCs B1121, B1122, and B1141, Will Not Flash, 4-Way Flashers Inoperable (Part 6 of 6)
Continued from
DTCs B1121, B1122, and B1141, Will Not Flash, 4-way Flashers Inoperable (Part 1 of 6).
Check for battery voltage at breakout box terminal 7 (Gray) with right turn signal depressed and
terminal 8 (Gray) with left turn signal depressed.
Is battery voltage present?
YES
Replace TSM/TSSM.
Learn password and
perform set-up.
NO
6791
3
Check for battery voltage on terminal 1
connector [22B] (right), or connector
[24B] (left).
Is battery voltage present?
5
YES
NO
With turn signal switch depressed
on side under test, check for continuity
between terminal 1 and terminal
5 on connector [22A] (right), or
connector [24A] (left).
Is continuity present?
Locate and repair open (O/W)
wire between terminal 1 on connector
[22B] (right), or connector
[24B] (left) and accessory fuse.
6814 – right
6812 - left
YES
NO
Locate and repair open wire
between terminal 5 on connector
[22B] (right), or connector [24B]
(left) and TSM/TSSM connector [30].
Replace turn signal
switch or repair wiring to
turn signal switch.
6813 – right
6810 - left
6811
fc02004_en
6
E-44 2009 Sportster Diagnostics: Appendix E TSM/TSSM (Japan/Korea)
Flash at Double Normal Rate, All Bulbs Working
Determine correct part number for all installed turn signal
bulbs and verify against parts installed on motorcycle.
Are the correct parts installed?
YES
NO
Check for corrosion
on bulbs and/or sockets.
Is corrosion present?
Replace with
correct bulbs.
6820
NO
YES
Remove corrosion with a wire brush.
Install ELECTRICAL CONTACT
LUBRICANT (Part No. 99861-02) in
bulb sockets.
Do lamps flash at normal rate?
Check for corrosion
on all lamp connection
terminals.
Is corrosion present?
YES
NO
System
OK.
6821
Clean or replace bulb.
Do lamps flash
at normal rate?
YES
NO
System
OK.
Replace
lamp
assembly.
6822
6823
YES
NO
Clean corrosion from
wires and terminals.
Do lamps flash at
normal rate?
Replace TSM/TSSM.
Learn password (if
needed) and perform
setup.
6824
YES
System
OK.
6822
NO
Replace TSM/TSSM
Learn password (if
needed) and perform
setup.
6824
fc01168_en
Verify that lamps are learned:
1) Turn ignition OFF - ON
2) Activate left turn lamp for 5 flashes.
3) Activate right turn lamp for 5 flashes.
Do the lamps flash at the normal rate?
NO
YES
System OK.
2009 Sportster Diagnostics: Appendix E TSM/TSSM (Japan/Korea) E-45
E.14
DTC B0563
GENERAL
Battery Voltage High
The TSM/TSSM continually checks the battery voltage during
IGN/OFF and IGN/RUN power modes. If the voltage exceeds
16.0 Volts for more than 5.0 ± 0.5 seconds, the TSM/TSSM
sets DTC B0563.
DIAGNOSTICS
Diagnostic Tips
•
This DTC may set when the vehicle is placed on a battery
charger, on fast charge, for a long period of time.
•
The TSSM does not illuminate the security lamp when this
DTC is set.
Diagnostic Notes
tests to correct. Problem may
be faulty voltage regulator.
E-46 2009 Sportster Diagnostics: Appendix E TSM/TSSM (Japan/Korea)
E.15
DTC B1131, B1132
GENERAL
NOTE
This section applies only to those vehicles equipped with the
optional security system.
Alarm Output Low (DTC B1131) or Alarm
Output High (DTC B1132)
. An alarm cycle is activated when the TSSM
is connected, the siren has been armed by the TSSM and a
security event occurs. See
. Under normal armed operation, the
siren input (terminal "2") is driven low by the TSSM to trigger
the audible alarm. When the siren input is driven high by the
TSSM the audible alarm stops.
ed02047
Figure E-21. Security Siren
DIAGNOSTICS
TOOL NAME
PART NUMBER
HARNESS CONNECTOR TEST KIT
HD-41404-B
BREAKOUT BOX
HD-42682
Diagnostic Tips
•
If the siren is armed and the internal siren battery is dead,
shorted, disconnected, or has been charging for a period
longer than 24 hours, the siren will respond with three
chirps on arming instead of two.
•
The internal siren battery may not charge if the vehicle's
battery is less than 12.5 volts.
•
If the siren does not chirp two or three times on a valid
arming command from the TSSM, the siren is either not
connected, not working, or the siren wiring was opened
or shorted while the siren was disarmed.
•
If the siren enters the self-driven mode where it is powered
from the siren internal nine-volt battery, the turn-signal
lamps will not alternately flash. If the TSSM activates the
siren, the turn-signal lamps will flash. If the siren has been
armed and a security event occurs, and the siren is in self-
driven mode, the siren will alarm for 20 to 30 seconds and
then turn off for 5 to 10 seconds. This alarm cycle will be
repeated ten times if the siren is in the self-driven mode.
•
If the siren does not stop alarming after it has been armed,
then either the TSSM output or siren input may be shorted
to ground, or the siren vehicle battery connection is open
or shorted to ground, or the siren vehicle ground connec-
tion is open, or a security event has occurred. See
E.6 SECURITY SYSTEM FUNCTIONS (TSSM ONLY)
for
a description of alarm functions.
Diagnostic Notes
Each reference number below correlates to a circled number
on the flowchart(s).
1.
Use BREAKOUT BOX (Part No. HD-42682) and HAR-
NESS CONNECTOR TEST KIT (Part No. HD-41404-B),
gray pin probe and patch cord. See
.
2.
Use HARNESS CONNECTOR TEST KIT (Part No. HD-
41404-B), gray socket probe and patch cord.
3.
Having the correct multimeter ohm scale is important for
this test. Some meters may read infinity for high ohm
values. If this is the case, check your ohm scale and retest.
2009 Sportster Diagnostics: Appendix E TSM/TSSM (Japan/Korea) E-47
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст