Harley Davidson 2018 softail models. Service manual — page 12
Be careful when installing E-clip, use E-clip tool
to help prevent damage to painted surfaces.
d. Install E-clip (5).
Special Tool: E-CLIP TOOL (HD-52369)
e. Push the long leg of the torsion spring into the slot
in the foot support bracket.
2.
Install wear peg, if equipped.
a. Apply threadlocker to wear peg.
LOCTITE 243 MEDIUM STRENGTH
THREADLOCKER AND SEALANT (BLUE)
(99642-97)
b. Install wear peg (6). Tighten.
Torque: 3.4-4.7 N·m (30-42 in-lbs) Wear peg
3.
See Figure 1. Install shift lever bracket.
a. Install shift lever bracket (2).
b. Apply threadlocker to screws.
LOCTITE 243 MEDIUM STRENGTH
THREADLOCKER AND SEALANT (BLUE)
(99642-97)
c. Install screws (3). Tighten.
Torque: 13.6-16.3 N·m (120-144 in-lbs) Shift lever
bracket screws
d. If removed, install O-rings (1).
1
O-ring (2)
2
Shift lever bracket
3
Screw (2)
Figure 1. Shift Lever Bracket
1
Foot support bracket
2
Clevis pin
3
Footboard
4
Torsion spring
5
E-clip
6
Wear peg
Figure 2. Left Side Footboard (Typical)
Special Tools
Description
Part Number
Qty.
E-CLIP TOOL
HD-52369
1
Consumables
Description
Part Number
Size
LOCTITE 243 MEDIUM STRENGTH
99642-97
6 ml (¼ fl oz)
THREADLOCKER AND SEALANT
(BLUE)
Disassemble
1. See Figure 1. Remove wear peg (7), if equipped.
2. Remove footpeg.
NOTE
When removing E-clip, use E-clip tool to prevent
damage to painted surfaces.
a. Remove E-clip (2).
Special Tool: E-CLIP TOOL (HD-52369)
b. Remove clevis pin (5).
c. Remove footpeg (3).
d. Remove torsion spring (4).
3. Inspect O-rings (1) for damage, replace if necessary.
Assemble
1. See Figure 1. Install footpeg (3).
a. Insert short leg of torsion spring (4) into hole in
footpeg.
b. Insert long leg of torsion spring into hole in foot
support (6).
c. Rotate footpeg into position and install clevis pin
(5).
NOTE
When installing E-clip, use E-clip tool to prevent
damage to painted surfaces.
d. Install E-clip (2).
Special Tool: E-CLIP TOOL (HD-52369)
2. If removed, install O-rings (1).
3. Install wear peg, if equipped.
a. Apply threadlocker to wear peg.
LOCTITE 243 MEDIUM STRENGTH
THREADLOCKER AND SEALANT (BLUE)
(99642-97)
b. Install wear peg (7). Tighten.
Torque: 3.4-4.7 N·m (30-42 in-lbs) Wear peg
1
O-ring (2)
2
E-clip
3
Footpeg
4
Torsion spring
5
Clevis pin
6
Foot support bracket
7
Wear peg
Figure 1. Left Side Footpeg (Typical)
1. Install shifter linkage. See Shifter Rod.
2. Remove vehicle from upright. See Secure the
Motorcycle for Service.
Consumables
Description
Part Number
Size
LOCTITE 243 MEDIUM STRENGTH
99642-97
6 ml (¼ fl oz)
THREADLOCKER AND SEALANT
(BLUE)
Remove
1. See Figure 1. Remove foot support bracket
a. Remove screws (2).
b. Remove foot support bracket (1).
2. See Figure 2. Remove brake pedal.
a. Remove rear master cylinder bracket (5). See
Prepare.
b. Remove rear brake master cylinder clevis pin (8).
See Prepare.
c. Remove flange nut (7) and washer (6).
d. Remove screw (1) and large washer (2).
e. Remove brake pedal (3).
f. Inspect O-rings (4) for damage, replace if necessary
Install
1. See Figure 2. Install brake pedal.
a. If removed, install O-rings (4).
b. Install brake pedal (3).
c. Install screw (1) and large washer (2).
d. Install washer (6) and flange nut (7). Tighten.
Torque: 24.4-29.8 N·m (18-22 ft-lbs) Brake pedal
pivot screw
e. Install rear brake master cylinder clevis pin (8). See
Prepare.
f. Install rear master cylinder bracket (5). See
Prepare.
2. See Figure 1. Install foot support bracket.
a. Apply threadlocker to screws (2).
LOCTITE 243 MEDIUM STRENGTH
THREADLOCKER AND SEALANT (BLUE)
(99642-97)
b. Install foot support bracket (1).
c. Install screws. Tighten.
Torque: 54.2-61 N·m (40-45 ft-lbs) Foot support
bracket screws
1
Foot support bracket
2
Screw (2)
Figure 1. Right Foot Support Bracket (Typical)
1
Screw
2
Large washer
3
Brake pedal
4
O-ring (2)
5
Bracket
6
Washer
7
Flange nut
8
Clevis pin
Figure 2. Brake Pedal
Consumables
Description
Part Number
Size
LOCTITE 243 MEDIUM STRENGTH
99642-97
6 ml (¼ fl oz)
THREADLOCKER AND SEALANT
(BLUE)
Remove
1. See Figure 1. Remove brake pedal.
a. Remove front brake pedal linkage screw (2).
b. Remove pivot screw (1) and washer (6).
c. Remove brake pedal.
d. Remove rear brake pedal linkage screw (5).
2. Remove foot support bracket
a. Remove screws (3).
b. Remove foot support bracket (4).
Install
1.
See Figure 1. Install foot support bracket.
a. Apply threadlocker to screws (3).
LOCTITE 243 MEDIUM STRENGTH
THREADLOCKER AND SEALANT (BLUE)
(99642-97)
b. Install foot support bracket (4).
c. Install screws (3). Tighten.
Torque: 54.2-61 N·m (40-45 ft-lbs) Foot support
bracket screws
2.
Install brake pedal.
a. Apply threadlocker to rear brake pedal linkage
screw (5).
LOCTITE 243 MEDIUM STRENGTH
THREADLOCKER AND SEALANT (BLUE)
(99642-97)
b. Install rear brake pedal linkage screw. Tighten.
Torque: 20.3-24.4 N·m (15-18 ft-lbs) Brake pedal
linkage screw
c. Install brake pedal.
d. Apply threadlocker to pivot screw (1).
LOCTITE 243 MEDIUM STRENGTH
THREADLOCKER AND SEALANT (BLUE)
(99642-97)
e. Install pivot screw and washer (6). Tighten.
Torque: 13.6-19 N·m (10-14 ft-lbs) Brake pedal
pivot screw
f. Apply threadlocker to front brake pedal linkage
screw (2).
LOCTITE 243 MEDIUM STRENGTH
THREADLOCKER AND SEALANT (BLUE)
(99642-97)
g. Install front brake pedal linkage screw. Tighten.
Torque: 20.3-24.4 N·m (15-18 ft-lbs) Brake pedal
linkage screw
1
Pivot screw
2
Front linkage screw
3
Screw (2)
4
Foot support bracket
5
Rear linkage screw
6
Washer
Figure 1. Right Side Mid Controls
Special Tools
Description
Part Number
Qty.
E-CLIP TOOL
HD-52369
1
Consumables
Description
Part Number
Size
LOCTITE 243 MEDIUM STRENGTH
99642-97
6 ml (¼ fl oz)
THREADLOCKER AND SEALANT
(BLUE)
Disassemble
1. See Figure 1. Remove wear peg (5), if equipped.
2. Remove footboard.
NOTE
When removing E-clip, use E-clip tool to help
prevent damage to painted surfaces.
a. Remove E-clip (3).
Special Tool: E-CLIP TOOL (HD-52369)
b. Remove clevis pin (6).
c. Remove torsion spring (2).
d. Remove footboard (4).
Assemble
1. See Figure 1. Install footboard.
a. Insert short leg of torsion spring (2) in hole in
footboard (4).
b. Position footboard and torsion spring on foot
support bracket (1).
c. Install clevis pin (6).
NOTE
When installing E-clip, use E-clip tool to help
prevent damage to painted surfaces.
d. Install E-clip (3).
Special Tool: E-CLIP TOOL (HD-52369)
e. Push the long leg of the torsion spring into the slot
in the foot support bracket.
2. Install wear peg, if equipped.
a. Apply threadlocker to wear peg.
LOCTITE 243 MEDIUM STRENGTH
THREADLOCKER AND SEALANT (BLUE)
(99642-97)
b. Install wear peg (5). Tighten.
Torque: 3.4-4.7 N·m (30-42 in-lbs) Wear peg
1
Foot support bracket
2
Torsion spring
3
E-clip
4
Footboard
5
Wear peg
6
Clevis pin
Figure 1. Right Side Footboard (Typical)
Special Tools
Description
Part Number
Qty.
E-CLIP TOOL
HD-52369
1
Consumables
Description
Part Number
Size
LOCTITE 243 MEDIUM STRENGTH
99642-97
6 ml (¼ fl oz)
THREADLOCKER AND SEALANT
(BLUE)
Disassemble
1. See Figure 1. Remove wear peg (4), if equipped.
2. Remove footpeg.
NOTE
When removing E-clip, use E-clip tool to help
prevent damage to painted surfaces.
a. Remove E-clip (5).
Special Tool: E-CLIP TOOL (HD-52369)
b. Remove clevis pin (1).
c. Remove footpeg (3).
d. Remove torsion spring (2).
Assemble
1. See Figure 1. Install footpeg.
a. Insert short leg of torsion spring (2) into hole in
footpeg (3).
b. Insert long leg of torsion spring into hole in foot
support bracket (6).
c. Rotate footpeg into position and install clevis pin
(1).
NOTE
When installing E-clip, use E-clip tool to help
prevent damage to painted surfaces.
d. Install E-clip (5).
Special Tool: E-CLIP TOOL (HD-52369)
2. Install wear peg, if equipped.
a. Apply threadlocker to wear peg.
LOCTITE 243 MEDIUM STRENGTH
THREADLOCKER AND SEALANT (BLUE)
(99642-97)
b. Install wear peg (4). Tighten.
Torque: 3.4-4.7 N·m (30-42 in-lbs) Wear peg
1
Clevis pin
2
Torsion spring
3
Footpeg
4
Wear peg
5
E-clip
6
Foot support bracket
Figure 1. Right Side Footpeg (Typical)
Special Tools
Description
Part Number
Qty.
E-CLIP TOOL
HD-52369
1
1.
See Passenger Footpeg. Remove footpeg.
NOTE
When removing e-clip, use e-clip tool to help prevent
damage to painted surfaces.
a. Remove e-clip (8).
Special Tool: E-CLIP TOOL (HD-52369)
b. Remove clevis pin (3).
NOTE
Remove footpeg and detent plate as an assembly
to keep detent ball and detent spring in place.
c. Remove footpeg (5) with detent plate (4).
2.
NOTE
Detent ball is under spring pressure, place finger over
detent ball when removing detent plate to keep detent
ball from falling out.
Remove detent plate from footpeg.
3.
Remove detent ball (7) and detent spring (6) from footpeg.
4.
Remove footpeg support (1).
a.
Remove screw (2).
b.
Remove footpeg support.
Special Tools
Description
Part Number
Qty.
E-CLIP TOOL
HD-52369
1
Consumables
Description
Part Number
Size
LOCTITE 243 MEDIUM STRENGTH
99642-97
6 ml (¼ fl oz)
THREADLOCKER AND SEALANT
(BLUE)
1.
See Figure 1. Install footpeg support (1).
a. Right side: Align notch in footpeg support with
alignment tab on exhaust bracket.
NOTE
FLHC and FLHCS do not have alignment tabs for
the passenger footpeg supports. Align footpeg
supports at a 5-15° rearward angle.
b. Left side: Align notch in footpeg support with rear
fork pivot shaft.
c. Apply threadlocker to screw (2).
LOCTITE 243 MEDIUM STRENGTH
THREADLOCKER AND SEALANT (BLUE)
(99642-97)
d. Install screw. Tighten.
Torque: 51.5-63.7 N·m (38-47 ft-lbs) Passenger
footpeg support screw
2.
Install detent spring (6) and detent ball (7) into footpeg (5).
3.
Install detent plate (4) onto footpeg.
NOTE
Hold detent ball in place while installing detent
plate to prevent detent ball from falling out.
Detent plate should be oriented with the detent
holes on the bottom.
Make sure detent ball is aligned with the
innermost hole in the detent plate when installed.
4.
NOTE
Install footpeg and detent plate as an assembly.
Install footpeg.
a. Install footpeg into footpeg support.
b. Install clevis pin (3).
NOTE
When installing e-clip, use e-clip tool to help
prevent damage to painted surfaces.
c. Install e-clip (8).
Special Tool: E-CLIP TOOL (HD-52369)
1
Footpeg support
2
Screw
3
Clevis pin
4
Detent plate
5
Footpeg
6
Detent spring
7
Detent ball
8
E-clip
Figure 1. Passenger Footpeg
1. Set motorcycle upright. See Secure the Motorcycle for
Service.
1. See Jiffy Stand Screws. Lower jiffy stand (1).
2. Remove screws (2).
3. Remove jiffy stand.
1. See Figure 1. Install Jiffy stand (1).
2. Install screws (2). Tighten.
Torque: 54.2-61 N·m (40-45 ft-lbs) Jiffy stand screws
1
Jiffy stand
2
Screw (2)
Figure 1. Jiffy Stand Screws
1. See Jiffy Stand (Typical). Remove JSS (Jiffy stand
sensor) (1), if equipped. See Prepare.
2. Remove spring (3).
3. Remove E-clip (4).
4. Remove clevis pin (8).
5. Remove jiffy stand (6).
6. Remove bushings (5).
7. Inspect bushings for wear or damage, replace if
necessary.
8. Remove jiffy stand bumper (7).
Consumables
Description
Part Number
Size
LOCTITE SILVER GRADE ANTI-
11100001
20.7 ml (0.7 fl oz)
SEIZE
1. See Figure 1. Install jiffy stand bumper (7).
2. Install bushings (5).
3. Install jiffy stand (6).
4. Apply anti-sieze lubricant to clevis pin (8).
LOCTITE SILVER GRADE ANTI-SEIZE (11100001)
5. Install clevis pin.
6. Install E-clip (4).
7. Apply anti-sieze lubricant to spring hook groove on jiffy
stand bracket (2).
LOCTITE SILVER GRADE ANTI-SEIZE (11100001)
NOTE
Spring hooks must point towards rear when jiffy stand
is down.
8. Install spring (3).
9. Install JSS (Jiffy stand sensor) (1), if equipped. See
Prepare.
1
JSS
2
Jiffy stand bracket
3
Spring
4
E-clip
5
Bushing (2)
6
Jiffy stand
7
Bumper
8
Clevis pin
Figure 1. Jiffy Stand (Typical)
1. Remove vehicle from upright. See Secure the
Motorcycle for Service.
Two-Up One-Piece Seat
1. See Seat Options. Remove seat.
a. Remove thumbscrew (1).
b. Slide seat tongue out of the frame.
c. Slide seat forward to remove from grab strap (4).
d. Remove Screw (10), washer (9) and grab strap (4),
if necessary.
Two-Up Two-Piece Seat
1. See Seat Options. Remove seat.
a. Remove the thumbscrew (1).
b. Remove the passenger pillion (3).
c. Remove mounting nuts (2).
d. Remove seat and grab strap (4), if necessary.
Solo Seat
1. See Seat Options. Remove seat.
a. Remove thumbscrew (1) or mounting nuts (2).
b. Remove seat.
Two-up One-piece Seat
1. See Figure 3. Install Seat.
NOTE
See for FXBR/S, FLFB/S, FXFB/S grab strap
installation.
a. Install washer (9), screw (10) and grab strap (4) if
removed. Tighten.
Torque: 6.8-10.16 N·m (60-90 in-lbs) One piece
seat grab strap screw
b. Install seat (5) rearward through the grab strap.
c. See Figure 1 and . Engage seat tongue in frame
bracket.
d. See Figure 3. Install thumbscrew (1). Tighten.
Torque: 1.7-3.4 N·m (15-30 in-lbs) Seat
thumbscrew
2. After installing seat, pull up on the seat to verify it is
secure.
Two-up Two-piece Seat
1. See Figure 3. Install Seat.
a. Install grab strap (4) if removed.
b. See Figure 1 and . Engage seat tongue in frame
bracket.
c. See Figure 3. Install mounting nuts (2).
d. Install passenger pillion (3).
e. Install thumbscrew (1). Tighten.
Torque: 1.7-3.4 N·m (15-30 in-lbs) Seat
thumbscrew
2. After installing seat, pull up on the seat to verify it is
secure.
Solo Seat
1. See Figure 3. Install Seat.
a. See Figure 1 and . Engage seat tongue in frame
bracket.
b. See Figure 3. Install thumbscrew (1), if equipped.
Tighten.
Torque: 1.7-3.4 N·m (15-30 in-lbs) Seat
thumbscrew
c. Install mounting nuts (2), if equipped. Tighten.
Torque: 1-1.7 N·m (9-15 in-lbs) Seat mounting nut
2. After installing seat, pull up on the seat to verify it is
secure.
Figure 1. Seat Tongue (Typical)
Figure 2. Seat Mounting Bracket
1
Thumbscrew
2
Mounting nut (2)
3
Pillion
4
Grab strap
5
Two-up one-piece seat
6
Two-up two-piece seat
7
Solo seat dual fastener
8
Solo seat single fastener
9
Washer
10
Screw
Figure 3. Seat Options
1
FXBR/S
2
FLFB/S
3
FXFB/S
Figure 4. Multi-hole Grab Strap Installation
1. Remove seat. See Remove.
1. See Frame Crossmember. If equipped with hydraulic
under seat adjust shock:
a. Remove screw (6) and washer (5).
b. Move preload adjuster (4) forward.
2. Remove wire harness anchor (7).
3. Remove small screw (2).
4. Remove mounting screws (1).
5. Remove frame crossmember (3).
1. See Figure 1. Install frame crossmember (3).
2. Install small screw (2) hand tight.
3. Install mounting screws (1). Tighten.
Torque: 23.1-27.1 N·m (17-20 ft-lbs) Frame
crossmember mounting screws
4. Tighten small screw.
Torque: 6.2-6.8 N·m (55-60 in-lbs) ECM caddy small
screw
5. Install wire harness anchor (7).
6. If equipped with hydraulic under seat adjust shock
absorber:
a. Install preload adjuster (4).
b. Install screw (6) and washer (5). Tighten.
Torque: 6.1-8.8 N·m (54-78 in-lbs) Shock adjuster
mounting screw
1
Mounting screw (2)
2
Small screw
3
Frame crossmember
4
Preload adjuster
5
Washer
6
Screw
7
Wire harness anchor
Figure 1. Frame Crossmember
1. Install seat. See Remove.
Consumables
Description
Part Number
Size
LOCTITE 243 MEDIUM STRENGTH
99642-97
6 ml (¼ fl oz)
THREADLOCKER AND SEALANT
(BLUE)
Remove
1. See Figure 2. Remove saddlebag.
a. Open saddlebag lid.
b. Remove screws (6).
c. Pull saddlebag (7) out and remove.
d. Remove spacers (5) and O-rings (4), if necessary.
2. See Figure 1. Remove right side mounting bracket
grommet.
a. Remove screw (2).
b. Remove mounting bracket grommet (1).
3. See Figure 2. Remove left side mounting bracket
grommet.
a. Remove screw (2).
b. Remove mounting bracket grommet (1).
c. Remove screw (8).
d. Remove mounting bracket (9).
Install
NOTICE
Check that saddlebag frame(s) are fully seated and tightly secured with mounting hardware. Failure to do so could
result in the saddlebags becoming detached and/or damaged. (00171b)
1. See Figure 1. Install right side mounting bracket
grommet.
a. Seat the mounting bracket grommet (1) nubs with
the holes on frame.
b. Apply threadlock to screw (2).
LOCTITE 243 MEDIUM STRENGTH
THREADLOCKER AND SEALANT (BLUE)
(99642-97)
c. Install screw. Tighten.
Torque: 10.9-13.6 N·m (96-120 in-lbs) Saddlebag
right side mounting bracket grommet screw
2.
See Figure 2. Install left side mounting bracket
grommet.
a. Position mounting bracket (9) on frame.
b. Apply threadlock to screw (8).
LOCTITE 243 MEDIUM STRENGTH
THREADLOCKER AND SEALANT (BLUE)
(99642-97)
c. Install screw. Tighten.
Torque: 52-64 N·m (38-47 ft-lbs) Saddlebag left
side mounting bracket screw
d. Seat the mounting bracket grommet (1) nubs with
the holes on mounting bracket.
e. Apply threadlock to screw (2).
LOCTITE 243 MEDIUM STRENGTH
THREADLOCKER AND SEALANT (BLUE)
(99642-97)
f. Install screw. Tighten.
Torque: 10.9-13.6 N·m (96-120 in-lbs) Saddlebag
left side mounting bracket grommet screw
3.
Install saddlebag.
a. Position docking rod (3) on mounting bracket
grommet (1).
b. Slide screws (6) through holes in saddlebag. Install
spacers (5) and O-rings (4), if removed.
c. Apply threadlock to screws (6).
LOCTITE 243 MEDIUM STRENGTH
THREADLOCKER AND SEALANT (BLUE)
(99642-97)
d. Align screws on saddlebag with holes on fender
support. Tighten.
Torque: 28-37 N·m (21-27 ft-lbs) Saddlebag screw
1
Mounting bracket grommet
2
Screw
3
Docking rod
Figure 1. Right Side Saddlebag Docking Rod
1
Mounting Bracket Grommet
2
Screw
3
Docking rod
4
O-ring (2)
5
Spacer (2)
6
Screw (2)
7
Saddlebag
8
Screw
9
Mounting bracket
Figure 2. Left Saddlebag
Consumables
Description
Part Number
Size
LOCTITE 243 MEDIUM STRENGTH
99642-97
6 ml (¼ fl oz)
THREADLOCKER AND SEALANT
(BLUE)
Remove
1.
See Figure 1. Remove saddlebag.
a. Open saddlebag outer clamshell (3).
b. Pull out and turn lock knob (4) to the unlocked
position (5).
c. Close saddlebag outer clamshell and lower latch
lever (2).
d. See Figure 2. Slide saddlebag rearward to
disengage the saddlebag docking rod (4) from the
mounting bracket grommet (5).
e. Lift saddlebag away from motorcycle.
2.
See Figure 3 and Figure 4. Remove docking mount.
a. Remove mounting bolt (5), docking mount (4) and
spacer (3).
3.
See Figure 3. Remove right side mounting bracket
grommet.
a. Remove screw (9).
b. Remove mounting bracket grommet (7).
4.
See Figure 4. Remove left side mounting bracket
grommet.
a. Remove screw (9).
b. Remove mounting bracket grommet (7).
c. Remove screw (11).
d. Remove mounting bracket (10).
Install
NOTICE
Check that saddlebag frame(s) are fully seated and tightly secured with mounting hardware. Failure to do so could
result in the saddlebags becoming detached and/or damaged. (00171b)
1. See Figure 3 and Figure 4. Install docking mount.
a. Slide docking mount (4) on mounting bolt (5).
b. Slide spacer (3) on mounting bolt.
c. Apply threadlock to mounting bolt.
LOCTITE 243 MEDIUM STRENGTH
THREADLOCKER AND SEALANT (BLUE)
(99642-97)
d. Install mounting bolt through fender supports into
fender mount. Tighten.
Torque: 28-37 N·m (21-27 ft-lbs) Saddlebag
mounting bolt
2.
See Figure 3. Install right side mounting bracket
grommet.
a. Seat the mounting bracket grommet (7) nubs with
the holes on bracket (8).
b. Apply threadlock to screw (9).
LOCTITE 243 MEDIUM STRENGTH
THREADLOCKER AND SEALANT (BLUE)
(99642-97)
c. Install screw. Tighten.
Torque: 11-14 N·m (97-124 in-lbs) Saddlebag right
side mounting bracket grommet screw
3.
See Figure 4. Install left side mounting bracket
grommet.
a. Position mounting bracket (10) on frame (8).
b. Apply threadlock to screw (11).
LOCTITE 243 MEDIUM STRENGTH
THREADLOCKER AND SEALANT (BLUE)
(99642-97)
c. Install screw. Tighten.
Torque: 52-64 N·m (38-47 ft-lbs) Saddlebag left
side mounting bracket screw
d. Seat the mounting bracket grommet (7) nubs with
the holes on mounting bracket.
e. Apply threadlock to screw (9).
LOCTITE 243 MEDIUM STRENGTH
THREADLOCKER AND SEALANT (BLUE)
(99642-97)
f. Install screw. Tighten.
Torque: 11-14 N·m (97-124 in-lbs) Saddlebag left
side mounting bracket grommet screw
4.
See Figure 1. Install saddlebag.
a. Open saddlebag outer clamshell (3).
b. Pull out and turn lock knob (4) to the unlocked
position (5).
c. See Figure 2. Place saddlebag mounting bracket
(2) on mounting studs (3) while aligning the
saddlebag docking rod (4) with the mounting
bracket grommet (5). Slide saddlebag completely
forward.
d. See Figure 1. Rotate lock knob to the locked
position (6) until a click is heard. Without pulling out
on the knob, verify that knob cannot rotate back to
the unlocked position.
NOTE
Indicator flag (1) is for showing when lock knob
is unlocked only. Do not use indicator flag to
lock or unlock saddlebag from motorcycle.
e. See Figure 2. Verify the indicator flag is not
showing and saddlebag is securely fastened.
f. Close saddlebag.
1
Lock
2
Latch lever
3
Outer clamshell
4
Lock knob
5
Unlocked position
6
Locked position
Figure 1. Saddlebag Lock Knob
1
Indicator flag (unlocked position)
2
Mounting bracket
3
Mounting stud (2)
4
Docking rod
5
Mounting bracket grommet
Figure 2. Saddlebag Mounting Bracket
1
Fender mount
2
Fender support
3
Spacer
4
Docking mount
5
Mounting bolt
6
Docking rod
7
Mounting bracket grommet
8
Bracket
9
Screw
Figure 3. Right Side Quick Disconnect Saddlebag
1
Fender mount
2
Fender support
3
Spacer
4
Docking mount
5
Mounting bolt
6
Docking rod
7
Mounting bracket grommet
8
Frame
9
Screw
10
Mounting bracket
11
Screw
Figure 4. Left Side Quick Disconnect Saddlebag
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст