LEXUS NX 300H (2019 year). Manual — part 22
348
6-3. Do-it-yourself maintenance
LEXUS NX300h Owners Manu-
al_USA_M78287_en
1
Turn the power switch off.
2
Open the glove box. Slide off the
damper.
3
Push in the glove box on the vehi-
cle’s outer side to disconnect the
claws. Then pull out the glove box
and disconnect the lower claws.
4
Remove the filter cover.
5
Remove the air conditioning filter
and replace it with a new one.
The “
UP” marks shown on the filter
should be pointing up.
■
Checking interval
Inspect and replace the air conditioning fil-
ter according to the maintenance schedule.
In dusty areas or areas with heavy traffic
flow, early replacement may be required.
(For scheduled maintenance information,
please refer to the “Owner’s Manual Sup-
plement” or “Scheduled Maintenance”.)
■
If air flow from the vents decreases dra-
matically
The filter may be clogged. Check the filter
and replace if necessary.
■
Air conditioning filter with deodorizing
function
When fragrances are placed in your vehi-
cle, the deodorizing effect may become
significantly weakened in a short period:
When an air conditioning odor comes out
continuously, replace the conditioning filter.
Air conditioning filter
The air conditioning filter must be
changed regularly to maintain air
conditioning efficiency.
Removal method
349
6-3. Do-it-yourself maintenance
LEXUS NX300h Owners Manu-
al_USA_M78287_en
6
Mai
nte
na
nc
e a
nd
c
are
■
When the card key battery needs to be
replaced (if equipped)
The battery for the card key is available only
at Lexus dealers. Your Lexus dealer can
replace the battery for you.
■
If the electronic key battery is depleted
The following symptoms may occur:
●
The smart access system with push-but-
ton start and wireless remote control will
not function properly.
●
The operational range will be reduced.
Prepare the following before replacing
the battery:
Flathead screwdriver
Lithium battery CR2032
■
Use a CR2032 lithium battery
●
Batteries can be purchased at your Lexus
dealer, local electrical appliance shops or
camera stores.
●
Replace only with the same or equivalent
type recommended by the manufacturer.
●
Dispose of used batteries according to
the local laws.
NOTICE
■
When using the air conditioning sys-
tem
Make sure that a filter is always installed.
Using the air conditioning system without
a filter may cause damage to the system.
Electronic key battery
Replace the battery with a new one
if it is depleted.
Items to prepare
350
6-3. Do-it-yourself maintenance
LEXUS NX300h Owners Manu-
al_USA_M78287_en
1
Take out the mechanical key.
2
Remove the cover.
To prevent damage to the key, cover the tip
of the flathead screwdriver with a tape.
3
Remove the depleted battery.
Insert a new battery with the “+” terminal
facing up.
Replacing the battery
WARNING
■
Removed battery and other parts
These parts are small and if swallowed by
a child, they can cause choking. Keep
away from children. Failure to do so
could result in death or serious injury.
NOTICE
■
For normal operation after replacing
the battery
Observe the following precautions to
prevent accidents:
●
Always work with dry hands.
Moisture may cause the battery to
rust.
●
Do not touch or move any other com-
ponent inside the remote control.
●
Do not bend either of the battery ter-
minals.
351
6-3. Do-it-yourself maintenance
LEXUS NX300h Owners Manu-
al_USA_M78287_en
6
Mai
nte
na
nc
e a
nd
c
are
1
Turn the power switch off.
2
Open the fuse box cover.
Engine compartment: type A fuse
box
Push the tab in and lift the lid off.
Engine compartment: type B fuse
box
Push the tab in and lift the lid off.
Left side instrument panel
Remove the lid.
Luggage compartment
3
Remove the fuse.
Only type A fuse can be removed using the
pullout tool.
4
Check if the fuse is blown.
Replace the blown fuse with a new fuse of
an appropriate amperage rating. The
amperage rating can be found on the fuse
box lid.
Checking and replacing
fuses
If any of the electrical components
do not operate, a fuse may have
blown. If this happens, check and
replace the fuses as necessary.
Checking and replacing fuses
352
6-3. Do-it-yourself maintenance
LEXUS NX300h Owners Manu-
al_USA_M78287_en
Type A
Normal fuse
Blown fuse
Type B
Normal fuse
Blown fuse
Type C
Normal fuse
Blown fuse
Type D
Normal fuse
Blown fuse
■
After a fuse is replaced
●
If the lights do not turn on even after the
fuse has been replaced, a bulb may need
replacement. (
●
If the replaced fuse blows again, have the
vehicle inspected by your Lexus dealer.
■
If there is an overload in a circuit
The fuses are designed to blow, protecting
the wiring harness from damage.
■
When replacing light bulbs
Lexus recommends that you use genuine
Lexus products designed for this vehicle.
Because certain bulbs are connected to cir-
cuits designed to prevent overload, non-
genuine parts or parts not designed for this
vehicle may be unusable.
A
B
A
B
A
B
WARNING
■
To prevent system breakdowns and
vehicle fire
Observe the following precautions.
Failure to do so may cause damage to
the vehicle, and possibly a fire or injury.
●
Never use a fuse of a higher amperage
rating than that indicated, or use any
other object in place of a fuse.
●
Always use a genuine Lexus fuse or
equivalent.
Never replace a fuse with a wire, even
as a temporary fix.
A
B
353
6-3. Do-it-yourself maintenance
LEXUS NX300h Owners Manu-
al_USA_M78287_en
6
Mai
nte
na
nc
e a
nd
c
are
Type A
Adjustment bolt A
Adjustment bolt B
Type B
Adjustment bolt A
Adjustment bolt B
Make sure the vehicle has a full tank
of gasoline and the area around the
headlight is not deformed.
Park the vehicle on level ground.
Make sure the tire inflation pressure
WARNING
●
Do not modify the fuses or fuse boxes.
■
Fuse box near the power control unit
Never check or replace the fuses as
there are high voltage parts and wiring
near the fuse box.
Doing so may cause electric shock,
resulting in death or serious injury.
NOTICE
■
Before replacing fuses
Have the cause of electrical overload
determined and repaired by your Lexus
dealer as soon as possible.
Headlight aim
Vertical movement adjusting
bolts
Before checking the headlight
aim
A
B
A
B
354
6-3. Do-it-yourself maintenance
LEXUS NX300h Owners Manu-
al_USA_M78287_en
is at the specified level.
Have someone sit in the driver’s
seat.
Bounce the vehicle several times.
1
Using a Phillips-head screwdriver,
turn bolt A in either direction.
Remember the turning direction
and the number of turns.
Type A
Type B
2
Turn bolt B the same number of
turns and in the same direction as
step 1.
If the headlight cannot be adjusted using
this procedure, take the vehicle to your
Lexus dealer to adjust the headlight aim.
Type A
Type B
Adjusting the headlight aim
355
6-3. Do-it-yourself maintenance
LEXUS NX300h Owners Manu-
al_USA_M78287_en
6
Mai
nte
na
nc
e a
nd
c
are
Front side marker light (bulb type)
Front turn signal light (bulb type)
■
Bulbs that need to be replaced by
the Lexus dealer
Headlights
Front turn signal lights (LED type)
Parking lights and Daytime running
lights
Front fog lights
Front side marker lights (LED type)
Side turn signal lights
Stop/tail lights
Rear side marker lights
Back-up light
Rear turn signal light
High mounted stoplight
License plate lights
Outer foot lights
■
LED lights
The lights other than the front side marker
lights (bulb type) and front turn signal lights
(bulb type) each consist of a number of
LEDs. If any of the LEDs burn out, take your
vehicle to your Lexus dealer to have the
light replaced.
■
Condensation build-up on the inside of
the lens
Temporary condensation build-up on the
inside of the headlight lens does not indi-
cate a malfunction. Contact your Lexus
dealer for more information in the following
situations:
●
Large drops of water have built up on the
inside of the lens.
●
Water has built up inside the headlight.
■
When replacing light bulbs
Light bulbs
You may replace the following bulbs
by yourself.
The difficulty level of replacement
varies depending on the bulb. If
necessary bulb replacement seems
difficult to perform, contact your
Lexus dealer.
For more information about replac-
ing other light bulbs, contact your
Lexus dealer.
Removing the engine compart-
ment cover
Bulb locations
A
B
356
6-3. Do-it-yourself maintenance
LEXUS NX300h Owners Manu-
al_USA_M78287_en
Before replacing, check the wattage of
the light bulb to be replaced.
(
■
Front side marker lights (bulb type)
1
Turn the bulb base counterclock-
wise.
2
Remove the light bulb.
3
When installing, reverse the steps
listed.
■
Front turn signal lights (bulb type)
1
Open the hood and remove the
cover for engine compartment
cover. (
2
Remove the cover.
Push the center of the clip
and remove
the clip and cover
.
3
Turn the bulb base counterclock-
wise.
4
Remove the light bulb.
5
Replace the light bulb.
Replacing light bulbs
A
B
357
6-3. Do-it-yourself maintenance
LEXUS NX300h Owners Manu-
al_USA_M78287_en
6
Mai
nte
na
nc
e a
nd
c
are
6
Turn clockwise and set the bulb
base.
7
Attach the clip to the cover.
Push up on the center of the clip and attach
the clip
.
Clip
8
Attach the cover.
Align the 2 tabs positions and close the
cover
and fix the cover by pushing the
center of the clip
.
9
Install the engine compartment
cover. (
A
A
A
B
WARNING
■
Replacing light bulbs
●
Be sure to stop the hybrid system and
turn off the lights. Do not attempt to
replace the bulb immediately after
turning off the lights.
The bulbs become very hot and may
cause burns.
●
Do not touch the glass portion of the
light bulb with bare hands. When it is
unavoidable to hold the glass portion,
use and hold with a clean dry cloth to
avoid getting moisture and oils on the
bulb.
Also, if the bulb is scratched or
dropped, it may blow out or crack.
●
Fully install light bulbs and any parts
used to secure them. Failure to do so
may result in heat damage, fire, or
water entering the headlight unit. This
may damage the headlights or cause
condensation to build up on the lens.
●
Do not attempt to repair or disassem-
ble light bulbs, connectors, electric cir-
cuits or component parts.
Doing so may result in death or serious
injury due to electric shock.
■
To prevent damage or fire
●
Make sure bulbs are fully seated and
locked.
●
Check the wattage of the bulb before
installing to prevent heat damage.
358
6-3. Do-it-yourself maintenance
LEXUS NX300h Owners Manu-
al_USA_M78287_en
359
LEXUS NX300h Owners Manu-
al_USA_M78287_en
7
7
When trouble
ari
ses
When trouble arises
7-1. Essential information
Emergency flashers. . . . ..
If your vehicle has to be stopped in
an emergency. . . . . . ..
7-2. Steps to take in an emergency
If your vehicle needs to be towed
. . . . . . . . . . . . . .
If you think something is wrong
. . . . . . . . . . . . . .
If a warning light turns on or a
warning buzzer sounds . ...
If a warning message is displayed
. . . . . . . . . . . . . .
If you have a flat tire. . . . ..
If the hybrid system will not start
. . . . . . . . . . . . . .
If you lose your keys. . . . .
If the fuel filler door cannot be
opened. . . . . . . . . .
If the electronic key does not
operate properly . . . . .
If the 12-volt battery is discharged
. . . . . . . . . . . . . .
If your vehicle overheats . .
If the vehicle becomes stuck
360
7-1. Essential information
LEXUS NX300h Owners Manu-
al_USA_M78287_en
7-1.Essential information
Press the switch.
All the turn signal lights will flash. To turn
them off, press the switch once again.
■
Emergency flashers
If the emergency flashers are used for a
long time while the hybrid system is not
operating (while the “READY” indicator is
not illuminated), the 12-volt battery may dis-
charge.
1
Steadily step on the brake pedal
with both feet and firmly depress it.
Do not pump the brake pedal repeatedly
as this will increase the effort required to
slow the vehicle.
2
Shift the shift lever to N.
If the shift lever is shifted to N
3
After slowing down, stop the vehi-
cle in a safe place by the road.
4
Stop the hybrid system.
If the shift lever cannot be shifted to
N
3
Keep depressing the brake pedal
with both feet to reduce vehicle
speed as much as possible.
4
To stop the hybrid system, press
and hold the power switch for 2
consecutive seconds or more, or
Emergency flashers
The emergency flashers are used to
warn other drivers when the vehicle
has to be stopped in the road due to
a breakdown, etc.
Operating instructions
If your vehicle has to be
stopped in an emergency
Only in an emergency, such as if it
becomes impossible to stop the
vehicle in the normal way, stop the
vehicle using the following proce-
dure:
Stopping the vehicle
361
7-1. Essential information
LEXUS NX300h Owners Manu-
al_USA_M78287_en
7
When trouble
ari
ses
press it briefly 3 times or more in
succession.
5
Stop the vehicle in a safe place by
the road.
WARNING
■
If the hybrid system has to be turned
off while driving
Power assist for the steering wheel will
be lost, making the steering wheel
heavier to turn. Decelerate as much as
possible before turning off the hybrid sys-
tem.
362
7-2. Steps to take in an emergency
LEXUS NX300h Owners Manu-
al_USA_M78287_en
7-2.Steps to take in an emergency
If your vehicle needs to be
towed
If towing is necessary, we recom-
mend having your vehicle towed by
your Lexus dealer or commercial
towing service, using a wheel-lift
type truck or flatbed truck.
Use a safety chain system for all
towing, and abide by all state/pro-
vincial and local laws.
If towing your vehicle with a wheel-
lift type truck, use a towing dolly.
(
WARNING
Observe the following precautions.
Failure to do so may result in death or
serious injury.
■
When towing the vehicle
Be sure to transport the vehicle with all
four wheels raised off the ground. If the
vehicle is towed with the tires contacting
the ground, the drivetrain or related
parts may be damaged, the vehicle may
fly off the truck, or electricity generated
by the operation of the motor may cause
a fire to occur depending on the nature
of the damage or malfunction.
■
While towing
●
When towing using a cables or chains,
avoid sudden starts, etc. which place
excessive stress on the towing eyelets,
cables or chains. The towing eyelets,
cables or chains may become dam-
aged, broken debris may hit people,
and cause serious damage.
●
Do not turn the power switch off.
There is a possibility that the steering
wheel is locked and cannot be oper-
ated.
■
Installing towing eyelets to the vehi-
cle
Make sure that towing eyelets are
installed securely.
If not securely installed, towing eyelets
may come loose during towing.
NOTICE
■
To prevent damage to the vehicle
when towing using a wheel-lift type
truck
●
Do not tow the vehicle from the rear
when the power switch is off. The
steering lock mechanism is not strong
enough to hold the front wheels
straight.
●
When raising the vehicle, ensure ade-
quate ground clearance for towing at
the opposite end of the raised vehicle.
Without adequate clearance, the vehi-
cle could be damaged while being
towed.
■
To prevent damage to the vehicle
when towing with a sling-type truck
Do not tow with a sling-type truck, either
from the front or rear.
363
7-2. Steps to take in an emergency
LEXUS NX300h Owners Manu-
al_USA_M78287_en
7
When trouble
ari
ses
The following may indicate a problem
with your hybrid transmission. Contact
your Lexus dealer or commercial tow-
ing service before towing. (
The hybrid warning message shows
on the multi-information display and
the vehicle does not move.
The vehicle makes an abnormal
sound.
Do not tow with a sling-type truck to
prevent body damage.
From the front
Use a towing dolly under the rear
wheels.
From the rear
Use a towing dolly under the front
wheels.
If your vehicle is transported by a flat-
bed truck, it should be tied down at the
locations shown in the illustration.
NOTICE
■
Recreational towing (behind motor
home, etc.)
Never dinghy tow your vehicle to pre-
vent causing serious damage to the
Hybrid AWD system and transmission.
(
Situations when it is necessary to
contact dealers before towing
Towing with a sling-type truck
Towing with a wheel-lift type
truck
Using a flatbed truck
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст