Lexus ES300 (1997 year). Service manual — part 404
N21462
(Example)
Inspection of
Slide Switch
8
12
–
DIAGNOSTICS
POWER SEAT CONTROL SYSTEM
DI–393
545
1997 LEXUS ES300 (RM511U)
OK
Proceed to next circuit inspection shown on
matrix chart (See page
NG
2
Check power seat control switch.
PREPARATION:
Disconnect power seat control switch connector.
CHECK:
Check continuity of each terminal.
OK:
Switch position
Terminal
Neutral
–
Slide switch FRONT
8 – 12
Slide switch BACK
4 – 12
Front vertical switch UP
10 – 12
Front vertical switch DOWN
10 – 12
Rear vertical switch UP
2 – 12
Rear vertical switch DOWN
3 – 12
Reclining switch FORWARD
1 – 12
Reclining switch REARWARD
5 – 12
NG
Replace power seat control switch.
OK
3
Check harness and connectors between Seat Position Control ECU and power
seat control switch (See page
).
NG
Repair or replace harness or connector.
OK
Check and replace Seat Position Control
ECU.
N21267
Seat Memory Switch
Seat Position Control ECU
SW1
SW2
MMRY
5
P
3
BR
9
6
7
BR
BR
BR
SGND
11
1
4
2
V
Y
S15
S15
S15
S15
BS2
IH
N22151
Seat Position Control ECU
Connect
(–)
(+)
SGND
MMRY
SW2 SW1
DI–394
–
DIAGNOSTICS
POWER SEAT CONTROL SYSTEM
546
1997 LEXUS ES300 (RM511U)
Seat Memory Switch
CIRCUIT DESCRIPTION
Seat memory switch send memory and return signals to the seat position control ECU.
WIRING DIAGRAM
INSPECTION PROCEDURE
1
Check voltage between each terminal of the seat memory switch and SGND of
Seat Position Control ECU connector.
PREPARATION:
Remove Seat Position Control ECU with connectors still con-
nected.
CHECK:
Measure voltage between terminal of the seat memory switch
and SGND of Seat Position Control ECU connector.
(The illustration shows inspection of the Memory 1 as an exam-
ple.)
OK:
At each terminal with switch ON
0 V
At each terminal with switch OFF
10
∼
14 V
OK
Proceed to next circuit inspection shown on
matrix chart (See page
DI0GH–01
N21463
(Example)
Inspection of SET Switch
2
1
–
DIAGNOSTICS
POWER SEAT CONTROL SYSTEM
DI–395
547
1997 LEXUS ES300 (RM511U)
NG
2
Check seat memory switch.
PREPARATION:
Disconnect seat memory switch connector.
CHECK:
Check continuity of each terminal.
OK:
Switch position
Terminal
SET switch ON
1 – 2
Memory switch 1
2 – 3
Memory switch 2
2 – 4
NG
Replace seat memory switch.
OK
3
Check harness and connectors between Seat Position Control ECU and seat
memory switch (See page
).
NG
Repair or replace harness or connector.
OK
Check and replace Seat Position Control
ECU.
DI01P–01
Customer Problem Analysis
Vehicle Brought to Workshop
Problem Symptom Confirmation
Symptom Simulation
Symptom does not occur
Problem Symptom Table
Circuit Inspection
Identification of Problem
Repair
Confirmation Test
End
Titles inside
are titles of pages in this
manual with the page number indicated in the
bottom portion. See the indicated pages
for detailed explanations.
1
2
3
4
5
7
Step 5, 7 : Diagnostic steps permitting the use
of the LEXUS hand–held tester and
LEXUS break–out–box.
P.
P.
P.
P.
∼
Symptom occur
6
DI–396
–
DIAGNOSTICS
THEFT DETERRENT SYSTEM
548
1997 LEXUS ES300 (RM511U)
THEFT DETERRENT SYSTEM
HOW TO PROCEED WITH TROUBLESHOOTING
HINT:
Troubleshooting of the theft deterrent system is based on the premise that the door lock control system is
operating normally. Accordingly, before troubleshooting the theft deterrent system, first make certain that
the door lock control system is operating normally.
For troubleshooting using a volt/ohm meter.
Be sure to use troubleshooting procedure appropriate to the diagnostic tool being used.
Perform troubleshooting in accordance with the procedure on the following page.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст