Lexus ES300 (1997 year). Service manual — part 364
S05334
LEXUS
Hand–Held Tester
DLC2
BR3890
F00006
DLC1
Short Pin
N09348
Hand–Held Tester
Brake–Out–Box
ECU
LEXUS
LEXUS
–
DIAGNOSTICS
ANTI–LOCK BRAKE SYSTEM
DI–233
385
1997 LEXUS ES300 (RM511U)
(c)
DTC CHECK USING LEXUS HAND–HELD TESTER
(1)
Hook up the LEXUS hand–held tester to the DLC2.
(2)
Read the DTC by following the prompts on the tes-
ter screen.
Please refer to the LEXUS hand–held tester opera-
tor’s manual for further details.
(d)
DTC CLEARANCE
(1)
Using SST, connect terminals Tc and E
1
of DLC2 or
DLC1 and remove the short pin from DLC1.
SST
09843 – 18020
(2)
IG switch ON.
(3)
Clear the DTC stored in ECU by depressing the
brake pedal 8 or more times within 5 seconds.
(4)
Check that the warning light shows the normal
code.
(5)
Remove the SST from the terminals of DLC2 or
DLC1.
SST
09843 – 18020
(6)
Connect the short pin to DLC1.
(e)
ECU TERMINAL VALUES MEASUREMENT
USING LEXUS BREAK –OUT–BOX AND
LEXUS HAND–HELD TESTER
(1)
Hook up the LEXUS hand–held tester and
LEXUS break–out–box to the vehicle.
(2)
Read the ECU input/output values by following the
prompts on the tester screen.
HINT:LEXUS hand–held tester has a ”Snapshot” function. This
records the measured values and is effective in the diagnosis
of intermittent problems.
Please refer to the LEXUS hand–held tester/LEXUS break–
out–box operator’s manual for further details.
F00007
DLC1
Ts
Tc
E
1
BR3904
0.13 sec.
0.13 sec.
ON
OFF
BR3893
Malfunction Code (Example Code 72, 76)
7
2
6
7
ON
OFF
0.5 sec.
0.5 sec.
0.5 sec.
0.5 sec.
1.5 sec.
2.5 sec.
4 sec.
Repeat
S05334
LEXUS
Hand–Held Tester
DLC2
DI–234
–
DIAGNOSTICS
ANTI–LOCK BRAKE SYSTEM
386
1997 LEXUS ES300 (RM511U)
2.
SPEED SENSOR SIGNAL
(a)
SPEED SENSOR SIGNAL CHECK
(1)
Turn the ignition switch OFF.
(2)
Using SST, connect terminals Ts and E
1
of DLC1.
SST
09843 – 18020
(3)
Start the engine.
(4)
Check that the ABS warning light blinks.
HINT:If the ABS warning light does not blink, inspect the ABS
warning light circuit (See page
(5)
Drive vehicle straight forward.
HINT:Drive vehicle faster than 45 km/h (28 mph) for several se-
conds.
(6)
Stop the vehicle.
(7)
Using SST, connect terminals Tc and E
1
of DLC1.
SST
09843 – 18020
(8)
Read the number of blinks of the ABS warning light.
HINT:See the list of DTC shown on the next page.
If every sensor is normal, a normal code is output (A cycle of
0.25 sec. ON and 0.25 sec. OFF is repeated).
If 2 or more malfunction are indicated at the same time, the low-
est numbered code will be displayed 1st.
(9)
After doing the check, disconnect the SST from ter-
minals Ts and E
1
, Tc and E
1
of DLC1, and turn igni-
tion switch OFF.
SST
09843 – 18020
(b)
DTC CHECK USING LEXUS HAND–HELD TESTER
(1)
Do step 1.
∼
6. on the previous page.
(2)
Hook up the LEXUS hand–held tester to the DLC2.
(3)
Read the DTC by following the prompts on the tes-
ter screen.
Please refer to the LEXUS hand–held tester opera-
tor’s manual for further details.
–
DIAGNOSTICS
ANTI–LOCK BRAKE SYSTEM
DI–235
387
1997 LEXUS ES300 (RM511U)
(c)
DTC OF SPEED SENSOR CHECK FUNCTION
Code No.
Diagnosis
Trouble Area
71
Low output voltage of right front speed sensor
Right front speed sensor
Sensor installation
Right front speed sensor rotor
72
Low output voltage of left front speed sensor
Left front speed sensor
Sensor installation
Left front speed sensor rotor
73
Low output voltage of right rear speed sensor
Right rear speed sensor
Sensor installation
Right rear speed sensor rotor
74
Low output voltage of left rear speed sensor
Left rear speed sensor
Sensor installation
Left rear speed sensor rotor
75
Abnormal change in output voltage of right front speed sen-
sor
Right front speed sensor rotor
76
Abnormal change in output voltage of left front speed
sensor
Left front speed sensor rotor
77
Abnormal change in output voltage of right rear speed
sensor
Right rear speed sensor rotor
78
Abnormal change in output voltage of left rear speed sensor
Left rear speed sensor rotor
DI0BE–01
DI–236
–
DIAGNOSTICS
ANTI–LOCK BRAKE SYSTEM
388
1997 LEXUS ES300 (RM511U)
DIAGNOSTIC TROUBLE CODE CHART
HINT:Using SST 09843 –18020, connect the terminals Tc and E
1
, and remove the short pin.
If a malfunction code is displayed during the DTC check, check the circuit listed that the code. For details
of each code, turn to the page referred to under the ”See page” for respective ”DTC No.” in the DTC chart.
DTC No.
(See Page)
Detection Item
Trouble Area
11
(
)
Open circuit in ABS solenoid relay circuit
ABS solenoid relay
12
(
)
Short circuit in ABS solenoid relay circuit
ABS solenoid relay
ABS solenoid relay circuit
13
(
)
Open circuit in ABS motor relay circuit
ABS motor relay
14
(
)
Short circuit in ABS motor relay circuit
ABS motor relay
ABS motor relay circuit
21
(
)
Open or short circuit in 2–position solenoid circuit for right front
wheel
ABS actuator
SFRR or SFRH circuit
22
(
)
Open or short circuit in 2–position solenoid circuit for left front
wheel
ABS actuator
SFLR or SFLH circuit
23
(
)
Open or short circuit in 2–position solenoid circuit for right rear
wheel
ABS actuator
SRRR or SRRH circuit
24
(
)
Open or short circuit in 2–position solenoid circuit for left rear
wheel
ABS actuator
SRLR or SRLH circuit
31
(
)
Right front wheel speed sensor signal malfunction
32
(
)
Left front wheel speed sensor signal malfunction
Right front, left front, right rear and left rear speed sensor
E
h
d
i
it
33
(
)
Right rear wheel speed sensor signal malfunction
Each speed sensor circuit
Speed sensor rotor
34
(
)
Left rear wheel speed sensor signal malfunction
33, 34
(
)
Rear speed sensor rotor faulty
Rear axle hub
Right rear, left rear speed sensor
Rear speed sensor circuit
41
(
)
Power source voltage down
Battery
IC regulator
Power source circuit
49
(
)
Open circuit in stop light switch circuit
Stop light switch
Stop light switch circuit
51
(
)
Pump motor is locked
ABS pump motor
Always ON
(
)
Malfunction in ECU
ECU
Battery
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст