LEXUS IS 300 (2019 year). Manual — part 10
152
3-3. Adjusting the seats
IS350 AWD/IS350/IS300 AWD/IS300_U
◆
Vertical adjustment
Up
Pull the head restraints up.
Down
Push the head restraint down while
pressing the lock release button.
◆
Horizontal adjustment (if equipped)
The position of the head restraint
can be adjusted forward in 4 stages.
If the head restraint is pulled forward
from the foremost position, it will return
to the rearmost position.
Head restraints
Head restraints are provided for all seats.
Front seats
Lock release button
1
2
153
3-3. Adjusting the seats
3
Op
era
tio
n of
ea
ch
co
m
po
ne
nt
IS350 AWD/IS350/IS300 AWD/IS300_U
Up
Pull the head restraints up.
Down
Push the head restraint down while
pressing the lock release button.
■
Removing the head restraints
■
Installing the head restraints
Front seats
Rear seats
Rear seats
Lock release button
1
2
Pull the head restraint up while pressing the lock
release button.
If the head restraint touches the ceiling, making
the removal difficult, change the seat height or
angle.
Align the head restraint with the installation
holes and push it down to the lock position.
Press and hold the lock release button when
lowering the head restraint.
Align the head restraint with the installation
holes and push it down to the lowest lock posi-
tion while pressing the lock release button.
Lock release button
Lock release button
Lock release button
154
3-3. Adjusting the seats
IS350 AWD/IS350/IS300 AWD/IS300_U
■
Adjusting the height of the head restraints
■
Adjusting the rear seat head restraint
Always raise the head restraint one level from the stowed position when using.
Make sure that the head restraints are adjusted
so that the center of the head restraint is closest
to the top of your ears.
WARNING
■
Head restraint precautions
Observe the following precautions regarding the head restraints. Failure to do so may
result in death or serious injury.
●
Use the head restraints designed for each respective seat.
●
Adjust the head restraints to the correct position at all times.
●
After adjusting the head restraints, push down on them and make sure they are
locked in position.
●
Do not drive with the head restraints removed.
155
3
Op
era
tio
n of
ea
ch
co
m
po
ne
nt
IS350 AWD/IS350/IS300 AWD/IS300_U
3-4. Adjusting the steering wheel and mirrors
Power type
Operating the switch moves the steering wheel in the following directions:
Up
Down
Toward the driver
Away from the driver
Manual type
Hold the steering wheel and push
the lever down.
Adjust to the ideal position by
moving the steering wheel hori-
zontally and vertically.
After adjustment, pull the lever up to
secure the steering wheel.
Steering wheel
Adjustment procedure
1
2
3
4
1
2
156
3-4. Adjusting the steering wheel and mirrors
IS350 AWD/IS350/IS300 AWD/IS300_U
To sound the horn, press on or close to
the
mark.
■
The steering wheel can be adjusted when (power type)
The engine switch is in ACCESSORY or IGNITION ON mode
*
.
*
: If the driver’s seat belt is fastened, the steering wheel can be adjusted regardless of
engine switch mode.
■
Automatic adjustment of the steering position (if equipped)
A desired steering position can be entered to memory and recalled automatically by the
driving position memory system. (
■
Power easy access system (if equipped)
The steering wheel and driver’s seat move in accordance with engine switch mode and
the driver’s seat belt condition. (
Horn
WARNING
■
Caution while driving
Do not adjust the steering wheel while driving.
Doing so may cause the driver to mishandle the vehicle and cause an accident, result-
ing in death or serious injury.
■
After adjusting the steering wheel (manual type)
Make sure that the steering wheel is securely locked.
Otherwise, the steering wheel may move suddenly, possibly causing an accident, and
resulting in death or serious injury. Also, the horn may not sound if the steering wheel is
not securely locked.
157
3-4. Adjusting the steering wheel and mirrors
3
Op
era
tio
n of
ea
ch
co
m
po
ne
nt
IS350 AWD/IS350/IS300 AWD/IS300_U
The height of the rear view mirror can be adjusted to suit your driving posture.
Adjust the height of the rear view mir-
ror by moving it up and down.
Responding to the level of brightness of the headlights of vehicles behind, the
reflected light is automatically reduced.
Changing automatic anti-glare func-
tion mode
ON/OFF
When the automatic anti-glare function
is in ON mode, the indicator illuminates.
The function will set to ON mode each
time the engine switch is turned to
IGNITION ON mode.
Pressing the button turns the function to
OFF mode. (The indicator also turns
off.)
Inside rear view mirror
The rear view mirror’s position can be adjusted to enable sufficient confirma-
tion of the rear view.
Adjusting the height of rear view mirror
Anti-glare function
Indicator
158
3-4. Adjusting the steering wheel and mirrors
IS350 AWD/IS350/IS300 AWD/IS300_U
■
To prevent sensor error
To ensure that the sensors operate properly, do
not touch or cover them.
WARNING
Do not adjust the position of the mirror while driving.
Doing so may lead to mishandling of the vehicle and cause an accident, resulting in death
or serious injury.
159
3-4. Adjusting the steering wheel and mirrors
3
Op
era
tio
n of
ea
ch
co
m
po
ne
nt
IS350 AWD/IS350/IS300 AWD/IS300_U
To select a mirror to adjust, press the
switch.
Left
Right
Pressing the same switch again will
put the switch in neutral.
To adjust the mirror, press the switch.
Up
Right
Down
Left
Push the mirror back in the direction of
the vehicle’s rear.
Outside rear view mirrors
Adjustment procedure
1
1
2
2
1
2
3
4
Folding the mirrors
160
3-4. Adjusting the steering wheel and mirrors
IS350 AWD/IS350/IS300 AWD/IS300_U
When either “L” or “R” of the mirror select switch is selected, the outside rear
view mirrors will automatically angle downwards when the vehicle is reversing in
order to give a better view of the ground.
To disable this function, select neither “L” nor “R”.
■
Adjusting the mirror angle when the vehicle is reversing
With the shift lever in R, adjust the mirror angle at a desired position.
The adjusted angle will be memorized and the mirror will automatically tilt to
the memorized angle whenever the shift lever is shifted to R from next time.
The memorized downward tilt position of the mirror is linked to the normal position
(angle adjusted with the shift lever in other than R). Therefore, if the normal posi-
tion is changed after adjustment, the tilt position will also change.
When the normal position is changed, readjust the angle in reversing.
■
Mirror angle can be adjusted when
The engine switch is in ACCESSORY or IGNITION ON mode.
■
When the mirrors are fogged up
The outside rear view mirrors can be cleared using the mirror defoggers. Turn on the
rear window defogger to turn on the outside rear view mirror defoggers. (
■
Automatic adjustment of the mirror angle (if equipped)
A desired mirror face angle can be entered to memory and recalled automatically by the
driving position memory. (
■
Auto anti-glare function (if equipped)
When the anti-glare inside rear view mirror is set to automatic mode, the outside rear
view mirrors will activate in conjunction with the anti-glare inside rear view mirror to
reduce reflected light. (
Linked mirror function when reversing (if equipped)
161
3-4. Adjusting the steering wheel and mirrors
3
Op
era
tio
n of
ea
ch
co
m
po
ne
nt
IS350 AWD/IS350/IS300 AWD/IS300_U
WARNING
■
Important points while driving
Observe the following precautions while driving.
Failure to do so may result in loss of control of the vehicle and cause an accident, result-
ing in death or serious injury.
●
Do not adjust the mirrors while driving.
●
Do not drive with the mirrors folded.
●
Both the driver and passenger side mirrors must be extended and properly adjusted
before driving.
■
When the mirror defoggers are operating
Do not touch the rear view mirror surfaces, as they can become very hot and burn you.
162
IS350 AWD/IS350/IS300 AWD/IS300_U
3-5. Opening, closing the windows and moon roof
The power windows can be opened and closed using the switches.
Operating the switch moves the windows as follows:
Closing
One-touch closing
*
Opening
One-touch opening
*
*
: To stop the window partway, operate the
switch in the opposite direction.
Press the switch to lock the passenger
window switches.
The indicator will come on.
Use this switch to prevent children from
accidentally opening or closing a pas-
senger window.
Power windows
Opening and closing procedures
1
2
3
4
Window lock switch
Indicator
163
3-5. Opening, closing the windows and moon roof
3
Op
era
tio
n of
ea
ch
co
m
po
ne
nt
IS350 AWD/IS350/IS300 AWD/IS300_U
■
The power windows can be operated when
The engine switch is in IGNITION ON mode.
■
Operating the power windows after turning the engine off
The power windows can be operated for approximately 45 seconds after the engine
switch is turned to ACCESSORY mode or turned off. They cannot, however, be oper-
ated once either front door is opened.
■
Jam protection function
If an object becomes jammed between the window and the window frame while the win-
dow is closing, window movement is stopped and the window is opened slightly.
■
Catch protection function
If an object becomes caught between the door and window while the window is opening,
window movement is stopped.
■
When the window cannot be opened or closed
When the jam protection function or catch protection function operates unusually and
the door window cannot be opened or closed, perform the following operations with the
power window switch of that door.
●
Stop the vehicle. With the engine switch in IGNITION ON mode, within 4 seconds of
the jam protection function or catch protection function activating, continuously oper-
ate the power window switch in the one-touch closing direction or one-touch opening
direction so that the door window can be opened and closed.
●
If the door window cannot be opened and closed even when performing the above
operations, perform the following procedure for function initialization.
Turn the engine switch to IGNITION ON mode.
Pull and hold the power window switch in the one-touch closing direction and com-
pletely close the door window.
Release the power window switch for a moment, resume pulling the switch in the
one-touch closing direction, and hold it there for approximately 6 seconds or more.
Press and hold the power window switch in the one-touch opening direction. After
the door window is completely opened, continue holding the switch for an additional
1 second or more.
Release the power window switch for a moment, resume pushing the switch in the
one-touch opening direction, and hold it there for approximately 4 seconds or
more.
Pull and hold the power window switch in the one-touch closing direction again.
After the door window is completely closed, continue holding the switch for a fur-
ther 1 second or more.
If you release the switch while the window is moving, start again from the beginning.
If the window reverses and cannot be fully closed or opened, have the vehicle inspected
by your Lexus dealer.
1
2
3
4
5
6
164
3-5. Opening, closing the windows and moon roof
IS350 AWD/IS350/IS300 AWD/IS300_U
■
Door lock linked window operation
●
The power windows can be opened and closed using the mechanical key.
*
(
●
The power windows can be opened using the wireless remote control.
*
(
P. 124)
*
: These settings must be customized at your Lexus dealer.
■
When the battery is disconnected
The window lock switch is disabled. If necessary, press the window lock switch after
reconnecting the battery.
■
Power windows open warning buzzer
The buzzer sounds and a message is shown on the multi-information display in the instru-
ment cluster when the engine switch is turned off and the driver’s door is opened with the
power windows open.
■
Customization
Settings (e.g. linked door lock operation) can be changed.
(Customizable features:
P. 613)
165
3-5. Opening, closing the windows and moon roof
3
Op
era
tio
n of
ea
ch
co
m
po
ne
nt
IS350 AWD/IS350/IS300 AWD/IS300_U
WARNING
Observe the following precautions.
Failure to do so may result in death or serious injury.
■
Closing the windows
●
The driver is responsible for all the power window operations, including the operation
for the passengers. In order to prevent accidental operation, especially by a child, do
not let a child operate the power windows. It is possible for children and other passen-
gers to have body parts caught in the power window. Also, when riding with a child, it
is recommended to use the window lock switch. (
●
Check to make sure that all passengers do not have any part of their body in a posi-
tion where it could be caught when a window is being operated.
●
When exiting the vehicle, turn the engine switch off, carry the key and exit the vehicle
along with the child. There may be accidental operation, due to mischief, etc., that
may possibly lead to an accident.
■
Jam protection function
●
Never use any part of your body to intentionally activate the jam protection function.
●
The jam protection function may not work if something gets jammed just before the
window is fully closed. Be careful not to get any part of your body jammed in the win-
dow.
■
Catch protection function
●
Never use any part of your body or clothing to intentionally activate the catch protec-
tion function.
●
The catch protection function may not work if something gets caught just before the
window is fully opened. Be careful not to get any part of your body or clothing caught
in the window.
166
3-5. Opening, closing the windows and moon roof
IS350 AWD/IS350/IS300 AWD/IS300_U
Opens the moon roof
*
The moon roof stops slightly before the
fully open position to reduce wind noise.
Press the switch again to fully open the
moon roof.
Closes the moon roof
*
*
: Lightly press either way of the moon
roof switch to stop the moon roof part-
way.
Tilts the moon roof up
*
Tilts the moon roof down
*
*
: Lightly press either way of the moon
roof switch to stop the moon roof part-
way.
Moon roof
: If equipped
Use the overhead switches to open and close the moon roof and tilt it up and
down.
Opening and closing
1
2
Tilting up and down
1
2
167
3-5. Opening, closing the windows and moon roof
3
Op
era
tio
n of
ea
ch
co
m
po
ne
nt
IS350 AWD/IS350/IS300 AWD/IS300_U
■
The moon roof can be operated when
The engine switch is in IGNITION ON mode.
■
Operating the moon roof after turning the engine off
The moon roof can be operated for approximately 45 seconds after the engine switch is
turned to ACCESSORY mode or turned off. It cannot, however, be operated once either
front door is opened.
■
Jam protection function
If an object is detected between the moon roof and the frame while the moon roof is clos-
ing or tilting down, travel is stopped and the moon roof opens slightly.
■
Sunshade
The sunshade can be opened and closed manually. However, the sunshade will open
automatically when the moon roof is opened.
■
Door lock linked moon roof operation
●
The moon roof can be opened and closed using the mechanical key.
*
(
●
The moon roof can be opened using the wireless remote control.
*
(
*
: These settings must be customized at your Lexus dealer.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст