Lexus SC300 / Lexus SC400. Service manual — part 379
ENGINE REMOVAL
EG24W–02
(See Components for Engine Removal and Installation)
1. REMOVE
BATTERY
CAUTION: Work must be started after 90 seconds from
the time the ignition switch is turned to the “LOCK” posi-
tion and the negative (–) terminal cable is disconnected
from the battery.
2. REMOVE
HOOD
3.
REMOVE ENGINE UNDER COVER
4.
DRAIN ENGINE COOLANT
5.
DRAIN ENGINE OIL
6.
REMOVE DRIVE BELT
Loosen the drive belt tension by turning the drive belt tension-
er counterclockwise, and remove the drive belt.
HINT: The pulley bolt for the drive belt tensioner has a left–
hand thread.
–
1UZ–FE ENGINE
ENGINE MECHANICAL
EG–139
7.
REMOVE THROTTLE BODY COVER
(a) Disconnect the EVAP hose from the hose clamp.
(b) Remove the cap nut.
(c) Loosen the 2 bolts, and remove the hose clamp and throttle
body cover.
8.
DISCONNECT CONTROL CABLES TO THROTTLE BODY
Disconnect the following cables:
(1)
Accelerator cable
(2)
Transmission throttle control cable
(3)
Cruise control actuator cable
9.
REMOVE AIR CLEANER
(a) Disconnect the VAF meter connector.
(b) Remove the hose clamp bolt holding the air cleaner hose to
the intake air connector.
(c) Remove the 4 bolts.
(d) Disconnect
the air cleaner hose from the intake air connector.
(e) Disconnect
the air duct from the air cleaner case, and remove
the air cleaner.
10. DISCONNECT VACUUM HOSE (A) (FROM PS AIR
CONTROL VALVE) FROM AIR INTAKE CHAMBER
11. REMOVE INTAKE AIR CONNECTOR
(a) Disconnect
the following hoses from the intake air connector:
(1) Air hose (from IAC valve)
(2) Air hose (from air control valve on PS pump)
(b) Remove the hose clamp bolt holding the intake air connector
to the throttle body.
(c) Remove the bolt and intake air connector.
EG–140
–
1UZ–FE ENGINE
ENGINE MECHANICAL
12. REMOVE RADIATOR RESERVOIR TANK
(a) Disconnect the coolant level sensor connector.
(b) Disconnect the following hoses:
(1)
Reservoir hose from water inlet housing
(2)
Reservoir hose from radiator
(c) Remove the 2 bolts and reservoir tank bracket.
(d) Remove the bolt holding the reservoir tank to the radiator.
(e) Disconnect
the reservoir tank from the reservoir tank bracket,
and remove the reservoir tank.
13. REMOVE
RADIATOR
ASSEMBLY
(a) Disconnect the ECT sensor connector (for cooling fan).
(b) Disconnect the ECT sensor wire clamp from the radiator fan
shroud.
(c) Disconnect the following hoses:
(1)
2 oil cooler hoses (for cooling fan) from pipes
(2)
2 radiator hoses
–
1UZ–FE ENGINE
ENGINE MECHANICAL
EG–141
(3)
2 oil cooler hoses (for transmission) from radiator
HINT: Plug the hose ends.
(4) Suction hose from hydraulic pump
(5) Pressure hose from hydraulic pump
(d) Remove the 2 bolts, screw and upper radiator support.
Remove the 2 upper radiator supports.
(e) Slightly lift the radiator, and disconnect the 2 oil cooler hoses
(for cooling fan) from the hose clamp on the radiator fan
shroud.
(f) Remove the radiator assembly.
(g) Remove the 2 lower radiator supports from the radiator.
14. DISCONNECT IGNITER CONNECTORS
(a) Disconnect the 2 igniter connectors.
(b) Disconnect the wire clamp from the body.
EG–142
–
1UZ–FE ENGINE
ENGINE MECHANICAL
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст