Lexus SC300 / Lexus SC400. Service manual — part 36
DRIVE BELT TENSION
INSPECTION OF DRIVE BELT TENSION
1.
INSPECT DRIVE BELT’S INSTALLATION CONDITION
Check that the drive belt fits properly in the ribbed grooves.
2.
INSPECT DRIVE BELT TENSION
Check that the tension is within the A range on the auto ten-
sioner scale.
If the tension is not within the A range on the scale, replace
the belt with a new one.
HINT: When replacing the drive belt with a new one, the belt’s
tension should be within the B range on the belt tensioner
scale.
IDLE–UP SPEED
INSPECTION OF IDLE SPEED
1.
WARM UP ENGINE
2.
INSPECT IDLE SPEED
ÑÑÑÑÑ
ÑÑÑÑÑ
ÑÑÑÑÑ
Trans–
mission
ÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
Magnetic clutch
condition
ÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
Standard idle
speed (rpm)
ÑÑÑÑÑ
ÑÑÑÑÑ
ÑÑÑÑÑ
A/T
(N range)
ÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
No engaged
ÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
650 rpm
ÑÑÑÑÑ
ÑÑÑÑÑ
ÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
Engaged
ÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
800 rpm
ÑÑÑÑÑ
ÑÑÑÑÑ
M/T
ÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
No engaged
ÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
700 rpm
ÑÑÑÑÑ
ÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
Engaged
ÑÑÑÑÑÑÑÑ
ÑÑÑÑÑÑÑÑ
900 rpm
AC–104
–
AIR CONDITIONING SYSTEM
Driver Belt Tension, Idle-Up Speed
REFRIGERANT LINES
TIGHTENING TORQUE OF
REFRIGERANT LINES
ON–VEHICLE INSPECTION
1.
INSPECT HOSES AND TUBES FOR LEAKAGE
Use a gas leak tester. Replace if necessary.
2. INSPECT HOSE AND TUBE CONNECTIONS FOR
LOOSENESS
–
AIR CONDITIONING SYSTEM
Refrigerant Lines
AC–105
REPLACEMENT OF REFRIGERANT
LINES
1.
RECOVER REFRIGERANT IN REFRIGERATION SYSTEM
See page
2.
REPLACE FAULTY TUBE OR HOSE
NOTICE: To prevent the intrusion of moisture or dirt, caps
should be placed on hose or tube ends immediately.
3.
TORQUE CONNECTIONS TO SPECIFIED TORQUE
NOTICE: Connections should not be torque tighter than the
specified torque.
4. EVACUATE REFRIGERATION SYSTEM AND CHARGE
WITH REFRIGERANT
See page
Specified amount: 950
±
50 g (33.44
±
1.76 oz)
5.
INSPECT FOR LEAKAGE OF REFRIGERANT
Using a gas leak tester, check for leakage of refrigerant.
6.
INSPECT A/C OPERATION
AC–106
–
AIR CONDITIONING SYSTEM
Refrigerant Lines
A/C UNIT
REMOVAL OF A/C UNIT
1.
RECOVER REFRIGERANT IN SYSTEM
See page
2. REMOVE
ENGINE
See page EM–118
3. REMOVE
WATER
VALVE
4.
REMOVE BRAKE TUBES BRACKET MOUNTING BOLTS
FROM DUSH PANEL
5. REMOVE
EVAPORATOR
6.
REMOVE WATER HOSE FROM HEATER RADIATOR
7. REMOVE
INSULATOR
RETAINER
Remove the two bolts and the retainer.
8.
REMOVE INSTRUMENT PANEL REINFORCEMENT
See page
9.
REMOVE FLOOR CARPET
See page
10. REMOVE REAR AIR DUCTS
Remove the nut and the air duct.
11. REMOVE HEATER TO RESISTER NO. 3 DUCT
Remove the screw and the duct.
–
AIR CONDITIONING SYSTEM
A/C Unit
AC–107
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст