Lexus SC300 / Lexus SC400. Service manual — part 568
(c) Set the timing mark (one dot mark) of the camshaft
driven gear at approx. 105 angle by turning the hexagon
wrench head portion of the exhaust camshaft with a
wrench.
(d) Alternately
loosen and remove the two bearing cap bolts
holding the intake camshaft side of the oil feed pipe to
the cylinder head.
(e) Uniformly loosen and remove the eight bearing cap
bolts in several passes in the sequence shown.
(f) Remove the oil feed pipe, four bearing caps and
exhaust camshaft.
B.
Remove intake camshaft from RH cylinder head
(a) Remove the rear bearing cap.
(b) Set the timing mark (one dot mark) of the camshaft drive
gear at approx. 455 angle by turning the hexagon
wrench head portion of the intake camshaft with a
wrench.
(c) Uniformly loosen and remove the eight bearing cap
bolts in several passes in the sequence shown.
(d) Remove the four bearing caps, oil seal and intake
camshaft.
–
ENGINE MECHANICAL
Cylinder Heads
EM–71
C.
Remove exhaust camshaft from LH cylinder head
(a) Bring the service bolt hole of the driven sub–gear
upward by turning the hexagon wrench head portion of
the exhaust camshaft with a wrench.
(b) Secure the exhaust camshaft sub–gear to the driven
gear with a service bolt.
Recommended service bolt:
Thread diameter 6 mm
Thread pitch 1.0 mm
Bolt length 16–20 mm (0.63–0.79 in.)
HINT: When removing the camshaft, make certain that the
torsional spring force of the sub–gear has been eliminated by
the above operation.
(c) Set the timing mark (two dot marks) of the camshaft
driven gear at approx. 155 angle by turning the hexagon
wrench head portion of the exhaust camshaft with a
wrench.
(d) Alternately
loosen and remove the two bearing cap bolts
holding the intake camshaft side of the oil feed pipe to
the cylinder head.
(e) Uniformly loosen and remove the eight bearing cap
bolts in several passes in the sequence shown.
(f) Remove the oil feed pipe, four bearing caps and
exhaust camshaft.
D.
Remove intake camshaft from LH cylinder head
(a) Remove the front bearing cap.
(b) Set the timing mark (one dot mark) of the camshaft drive
gear at approx. 605 angle by turning the hexagon
wrench head portion of the intake camshaft with a
wrench.
EM–72
–
ENGINE MECHANICAL
Cylinder Heads
(c) Uniformly loosen and remove the eight bearing cap
bolts in several passes in the sequence shown.
(d) Remove the four bearing caps, oil seal and intake
camshaft.
HINT: Arrange the bearing caps in correct order.
42. DISASSEMBLE EXHAUST CAMSHAFTS
(a) Mount the hexagon wrench head portion of the
camshaft in a vise.
NOTICE: Be careful not to damage the camshaft.
(b) Insert a service bolt (A) into the service hole of the
camshaft sub–gear.
(c) Using a screwdriver, turn the sub–gear clockwise, and
remove the service bolt (B).
NOTICE: Be careful not to damage the camshaft.
(d) Using snap ring pliers, remove the snap ring.
–
ENGINE MECHANICAL
Cylinder Heads
EM–73
(e) Remove the following parts:
(1)
Wave washer
(2)
Camshaft sub–gear
(3)
Camshaft gear spring
HINT: Arrange the camshaft sub–gears and gear springs (RH
side and LH side).
43. REMOVE CIRCULAR PLUGS
Remove the two bolts, seal washers, bearing cap and circular
plug. Remove the two circular plugs.
HINT: Arrange the bearing caps (RH side and LH side).
44. DISCONNECT MAIN OXYGEN SENSOR CONNECTORS
Disconnect the RH and LH oxygen sensor connector.
EM–74
–
ENGINE MECHANICAL
Cylinder Heads
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст