Lexus LS400 (2000 year). Service manual — part 88
EM–6
–
ENGINE MECHANICAL
VALVE CLEARANCE
1188
Intake:
N = T + (A – 0.20 mm (0.008 in.))
Exhaust:
N = T + (A – 0.30 mm (0.012 in.))
Select a new shim with a thickness as close as pos-
sible to the calculated value.
HINT:
Shims are available in 41 increments of 0.020 mm (0.0008 in.),
from 2.00 mm (0.0787 in.) to 2.80 mm (0.1102 in.).
(e)
Place a new adjusting shim on the valve.
(f)
Place the valve lifter.
(g)
Reinstall the camshafts. (See page
)
(h)
Reinstall the timing belt. (See page
)
(i)
Recheck the valve clearance.
13.
REINSTALL CYLINDER HEAD COVERS
14.
REINSTALL IGNITION COILS
15.
REINSTALL NO.3 TIMING BELT COVERS
(See page
)
16.
REINSTALL AIR CLEANER AND INTAKE AIR CON-
NECTOR ASSEMBLY
17.
REFILL WITH ENGINE COOLANT
18.
START ENGINE AND CHECK FOR LEAKS
19.
RECHECK ENGINE COOLANT LEVEL
20.
REINSTALL V–BANK COVER
21.
REINSTALL AIR CLEANER INLET
22.
REINSTALL BATTERY CLAMP COVER
A031
1
1
Adjusting Shim Selection Chart (Intake)
Shim No.
Installed shim thickness
mm (in.)
mm (in.)
Measured clearance
Thickness
New shim thickness
Shim No.
Thickness
Shim No.
Thickness
mm (in.)
Intake valve clearance (Cold):
0.15 – 0.25 mm (0.006 – 0.010 in.)
EXAMPLE:
The 2.300 mm (0.0906 in.) shim is installed,
and the measured clearance is 0.440 mm
(0.0173 in.). Replace the 2.300 mm (0.0906
in.) shim with a No. 54 shim.
–
ENGINE MECHANICAL
V
A
L
VE CLEARANCE
EM–7
1
189
2000
A031
12
Adjusting Shim Selection Chart (Exhaust)
Installed shim thickness
mm (in.)
mm (in.)
Measured clearance
Shim No.
Thickness
New shim thickness
Shim No.
Thickness
Shim No.
Thickness
mm (in.)
Exhaust valve clearance (Cold):
0.25 – 0.35 mm (0.010 – 0.014 in.)
EXAMPLE:
The 2.300 mm (0.0906 in.) shim is installed,
and the measured clearance is 0.440 mm
(0.0173 in.). Replace the 2.300 mm (0.0906
in.) shim with a No. 44 shim.
EM–8
–
ENGINE MECHANICAL
V
A
L
VE CLEARANCE
1
190
2000
EM09R–02
A03191
SST
A03192
–
ENGINE MECHANICAL
CYLINDER HEAD
EM–43
1225
DISASSEMBLY
1.
REMOVE VALVE LIFTERS AND SHIMS
HINT:
Arrange the valve lifters and shims in correct order.
2.
REMOVE VALVES
(a)
Using SST, compress the valve spring and remove the 2
keepers.
SST
09202–70020
(b)
Remove the spring retainer.
(c)
Remove the valve spring.
(d)
Remove the valve.
(e)
Remove the spring seat.
HINT:
Arrange the valves, valve springs, spring seats and spring re-
tainers incorrect order.
(f)
Using needle–nose pliers, remove the oil seal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст