Lexus LS400 (2000 year). Service manual — part 37
BE0CZ–01
I03405
Engine Room Junction Block
DOME Fuse
RADIO No.1 Fuse
Instrument Panel
Junction Block
RADIO No.2 Fuse
Ignition Switch
Tweeter
Speaker
CD Auto
Changer
Radio Receiver
Assembly
Rear Door Speaker
Front Door Speaker
Power Amplifier
Tweeter Speaker
Front Door Speaker
Rear Door Speaker
Woofer Speaker
–
BE–225
2088
LOCATION
BE0D0–01
Z14756
Wire Harness Side
Connector ”A”
Connector ”B”
Connector ”C”
Z14757
Wire Harness Side
Connector ”A”
Connector ”B”
Connector ”C”
Connector ”D”
e–9–1 e–13–1–A
eh–14–1 h–14–1–A
BE–226
–
BODY ELECTRICAL
AUDIO SYSTEM
2089
INSPECTION
1.
Nakamichi made:
INSPECT RADIO RECEIVER ASSEMBLY CIRCUIT
Disconnect the connectors from the radio receiver assembly.
And inspect the connector on the wire harness side, as shown.
Tester connection
Condition
Specified condition
B14 – Ground
Constant
Continuity
B6 – Ground
Ignition switch position ACC or ON
Battery positive voltage
B6 – Ground
Ignition switch position LOCK
No voltage
B1 – Ground
Constant
Battery positive voltage
If circuit is not as specified, inspect the circuits connected to oth-
er parts.
HINT:
Check the wire harness between radio receiver assembly and
the CD auto changer, between radio receiver assembly and
power amplifier.
2.
Nakamichi made:
INSPECT POWER AMPLIFIER CIRCUIT
Disconnect the connector from the power amplifier and inspect
the connector on the wire harness side, as shown.
Z14758
Wire Harness Side
h–14–1–A
–
BODY ELECTRICAL
AUDIO SYSTEM
BE–227
2090
Tester connection
Condition
Specified condition
A4 – Ground
Constant
Continuity
A5 – Ground
Constant
Battery positive voltage
A6 – Ground
Ignition switch position ACC or ON
Battery positive voltage
D6 – Ground
Ignition switch position ACC or ON
Radio, Tape or CD switch ON
Battery positive voltage
If circuit is not as specified, inspect the circuits connected to oth-
er parts.
3.
Nakamichi made:
INSPECT CD AUTO CHANGER CIRCUIT
Disconnect the connectors from the controller and inspect the
connector on the wire harness side, as shown.
Tester connection to
terminal number
Condition
Specified condition
5 – Ground
Constant
Battery positive voltage
4 – Ground
Ignition switch LOCK
No voltage
4 – Ground
Ignition switch ACC or ON
Battery positive voltage
If circuit is not as specified, inspect the circuits connected to oth-
er parts.
HINT:
Since the signals to and from the AP+, AP–, SGND, GND1 ter-
minals are serial signals, they cannot ordinarily be measured
with a tester.
I03482
Wire Harness Side
Connector ”A”
Connector ”B”
I03483
Wire Harness Side
Connector ”A”
Connector ”B”
Connector ”C”
Connector ”E”
Connector ”D”
BE–228
–
BODY ELECTRICAL
AUDIO SYSTEM
2091
4.
Pioneer made:
INSPECT RADIO RECEIVER ASSEMBLY CIRCUIT
Disconnect the connectors from the radio receiver assembly.
And inspect the connector on the wire harness side, as shown.
Tester connection
Condition
Specified condition
B1 – Ground
Constant
Continuity
A6 – Ground
Ignition switch position ACC or ON
Battery positive voltage
A6 – Ground
Ignition switch position LOCK
No voltage
A1 – Ground
Constant
Battery positive voltage
If circuit is not as specified, inspect the circuits connected to oth-
er parts.
HINT:
Check the wire harness between power amplifier and the CD
auto changer, between radio receiver assembly and power am-
plifier.
5.
Pioneer made and LEXUS navigation system:
INSPECT POWER AMPLIFIER CIRCUIT
Disconnect the connector from the power amplifier and inspect
the connector on the wire harness side, as shown.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст