Lexus GS300/400 (2000 year). Service manual — part 91
I04072
4
3
I04073
5
4
I04074
1
5
4
2
I04076
Wire Harness Side
BE–78
–
BODY ELECTRICAL
WIPER AND WASHER SYSTEM
2379
4.
INSPECT WIPER MOTOR OPERATION
High speed:
Connect the positive (+) lead from the battery to terminal 3 and
the negative (–) lead to terminal 4, check that the motor oper-
ates at high speed.
If operation is not as specified, replace the motor.
5.
INSPECT WIPER MOTOR OPERATION
Stopping at stop position:
(a)
Operate the motor at low speed and stop the motor opera-
tion anywhere except at the stop position by disconnect-
ing positive (+) lead from terminal 5.
(b)
Connect terminals 1 and 5.
(c)
Connect the positive (+) lead from the battery to terminal
2 and negative (–) lead to terminal 4, check that the motor
stops running at the stop position after the motor operates
again.
If operation is not as specified, replace the motor.
6.
INSPECT WIPER MOTOR CIRCUIT
Connector disconnected:
Disconnect the connector from the motor and inspect the con-
nector on the wire harness side, as shown.
Tester connection
Condition
Specified condition
4 – Ground
Constant
Continuity
2 – Ground
Ignition switch LOCK or ACC
No voltage
2 – Ground
Ignition switch ON
Battery positive voltage
If circuit is not as specified, inspect the circuits connected to oth-
er parts.
I01272
2
1
I04077
Wire Harness Side
–
BODY ELECTRICAL
WIPER AND WASHER SYSTEM
BE–79
2380
7.
INSPECT WASHER MOTOR OPERATION
Connect the positive (+) lead from the battery to terminal 2 and
the negative (–) lead to terminal 1, check that the motor oper-
ates.
NOTICE:
These tests must be performed quickly (within 20 seconds) to
prevent the coil from burning out.
If operation is not as specified, replace the motor.
8.
INSPECT WASHER MOTOR CIRCUIT
Connector disconnected:
Disconnect the connector from the motor and inspect the con-
nector on the wire harness side, as shown.
Tester connection
Condition
Specified condition
2 – Ground
Ignition switch ON
Battery positive voltage
If circuit is not as specified, inspect the power source, wire har-
ness and wiper switch.
BE0HH–07
I01359
Brake Master Cylinder
Brake Fluid Level
Warning Switch
Combination Meter
and Telltale Light
Assembly
Airbag Sensor Assembly
Parking Brake Switch
Driver Side
Junction Block
GAUGE Fuse
SRS–B Fuse
Ignition Switch
ECM
Washer Tank
Washer Level
Warning Switch
Engine Room No.1
Junction Block
MPX–B Fuse
Seat Belt Buckle Switch
Rheostat Light Control
ABS, TRAC and VSC ECU
Clock Assembly
Passenger Seat Belt
Waning Light
BE–80
–
BODY ELECTRICAL
COMBINATION METER
2381
COMBINATION METER
LOCATION
The vehicle shown in this illustration is ”GS400”.
All components of ”GS300” other than the ones used for engine are same as ”GS400”.
I01360
Fuel Tank
Fuel Main
Sender Gauge
Fuel Tank
Fuel Sub
Sender Gauge
Occupant Detection Sensor
(Passenger seat belt
warning sensor)
Engine Oil Level
Warning Sensor
Engine Oil Level
Warning Sensor
Park/ Neutral
Position Switch
Low Oil Pressure
Warning Switch
Park/ Neutral
Position Switch
Low Oil Pressure
Warning Switch
GS300
GS400
Light Failure Sensor
–
BODY ELECTRICAL
COMBINATION METER
BE–81
2382
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст