Lexus GS300/400 (2000 year). Service manual — part 166
–
LUBRICATION (2JZ–GE)
OIL AND FILTER
LU–3
1575
(b)
Fill with fresh engine oil.
Capacity:
Drain and refill
w/ Oil filter change
w/o Oil filter change
5.4 liters (5.7 US qts, 4.8 lmp. qts)
5.1 liters (5.4 US qts, 4.5 lmp. qts)
Dry fill
6.5 liters (6.9 US qts, 5.7 lmp. qts)
(c)
Reinstall the oil filler cap.
4.
START ENGINE AND CHECK FOR OIL LEAKS
5.
RECHECK ENGINE OIL LEVEL
LU05I–01
B01978
No.3 Timing Belt Cover
Oil Filler Cap
Engine Wire Clamp
Crankshaft Position Sensor
Oil Pump
Oil Level Sensor Connector
Oil Dipstick and Guide
O–Ring
Gasket
Crankshaft Front Oil Seal
Timing Belt Plate
No.2 Timing Belt Cover
Timing Belt
Oil Level Sensor
Oil Strainer
Oil Pan Baffle Plate
Timing Belt Tensioner
Engine Oil Drain Plug
Timing Belt Guide
Drive Belt Tensioner
No.1 Timing Belt Cover
No.2 Oil Pan
Gasket
Idler Pulley
35 (350, 26)
O–Ring
O–Ring
21 (210, 15)
x 9
8.0 (80, 71 in.·lbf)
x 5
Gasket
x 16
Gasket
x 6
x 16
No.1 Oil Pan
Crankshaft Pulley
330 (3,300, 243)
27 (270, 20)
Dust Boot
Crankshaft Timing
Pulley
Gasket
x 6
N·m (kgf·cm, ft·lbf)
: Specified torque
Non–reusable part
Precoated part
LU–4
–
LUBRICATION (2JZ–GE)
OIL PUMP
1576
OIL PUMP
COMPONENTS
B01643
Plug
Gasket
Compression Spring
Relief Valve
Oil Pump Body
Driven Rotor
Drive Rotor
Oil Pump Body Cover
x 10
Non–reusable part
–
LUBRICATION (2JZ–GE)
OIL PUMP
LU–5
1577
LU05J–01
B01989
O–Ring
Pull
P10747
Z02375
SST
SST
LU–6
–
LUBRICATION (2JZ–GE)
OIL PUMP
1578
REMOVAL
HINT:
When repairing the oil pump, the oil pan and strainer should be
removed and cleaned.
1.
REMOVE ENGINE WITH TRANSMISSION
(See page
2.
SEPARATE ENGINE AND TRANSMISSION
(See page
3.
INSTALL ENGINE TO ENGINE STAND FOR
REMOVAL
4.
REMOVE CRANKSHAFT POSITION SENSOR
5.
REMOVE TIMING BELT,
IDLER PULLEY AND CRANK-
SHAFT TIMING PULLEY
(See page
)
6.
REMOVE OIL DIPSTICK AND GUIDE
(a)
Disconnect the engine wire clamp from the dipstick guide.
(b)
Remove the bolt.
(c)
Pull out the dipstick guide together with the dipstick.
(d)
Remove the O–ring from the dipstick guide.
7.
REMOVE OIL LEVEL SENSOR
(a)
Disconnect the level sensor connector.
(b)
Remove the 4 bolts and level sensor.
(c)
Remove the gasket from the level sensor.
NOTICE:
Be careful not to drop the oil level sensor when removing
it.
8.
REMOVE NO.2 OIL PAN
(a)
Remove the 16 bolts and 2 nuts.
(b)
Insert the blade of SST between the No.1 and No.2 oil
pan, break the seal of the applied sealer and remove the
No.2 oil pan.
SST
09032–00100
NOTICE:
Be careful not to damage the No.2 oil pan contact surface
of the No.1 oil pan. Be careful not to damage the oil pan
flange.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст