Lexus RX300 (MCU15). Service manual — part 138
I19147
UNLOCK
LOCK
Door Lock Cable
UNLOCK
LOCK
4
3
4
3
I19148
2
UNLOCK
LOCK
UNLOCK
LOCK
2
1
1
Door Lock Cable
–
BODY ELECTRICAL
POWER DOOR LOCK CONTROL SYSTEM
BE–99
LEXUS RX300 (RM785E)
10.
Driver’s Door (LHD)/Passenger’s Door (RHD):
INSPECT DOOR LOCK MOTOR OPERATION
(a)
Connect the positive (+) lead from the battery to terminal
4 and the negative (–) lead to terminal 3, and check that
the door lock cable moves to UNLOCK position.
(b)
Reverse the polarity and check that the door lock cable
moves to LOCK position.
If operation is not as specified, replace the door lock assembly.
11.
Driver’s Door (LHD)/Passenger’s Door (RHD):
INSPECT DOOR LOCK MOTOR CIRCUIT
(See page DI–606)
12.
Passenger ’s door (LHD)/Driver’s Door (RHD):
INSPECT DOOR LOCK MOTOR OPERATION
(a)
Connect the positive (+) lead from the battery to terminal
2 and the negative (–) lead to terminal 1, and check that
the door lock cable moves to UNLOCK position.
(b)
Reverse the polarity and check that the door lock cable
moves to LOCK position.
If operation is not as specified, replace the door lock assembly.
13.
Front right side door:
INSPECT DOOR LOCK MOTOR CIRCUIT
(See page DI–628)
I19149
UNLOCK
LOCK
UNLOCK
LOCK
Door Lock Cable
2
6
6
2
I07312
LOCK
UNLOCK
UNLOCK
LOCK
3
2
3
2
I19150
4
3
UNLOCK
LOCK
Door Lock Cable
BE–100
–
BODY ELECTRICAL
POWER DOOR LOCK CONTROL SYSTEM
LEXUS RX300 (RM785E)
14.
INSPECT REAR DOOR LOCK MOTOR OPERATION
(a)
Connect the positive (+) lead from the battery to terminal
6 and the negative (–) lead to terminal 2, and check that
the door lock cable moves to UNLOCK position.
(b)
Reverse the polarity and check that the door lock cable
moves to LOCK position.
If operation is not as specified, replace the door lock assembly.
15.
INSPECT REAR DOOR LOCK MOTOR CIRCUIT
(See page DI–651)
16.
INSPECT BACK DOOR LOCK MOTOR OPERATION
(a)
Connect the positive (+) lead from the battery to terminal
1 and the negative (–) lead to terminal 3, and check that
the door lock link moves to UNLOCK position.
(b)
Reverse the polarity and check that the door lock link
moves to LOCK position.
If operation is not as specified, replace the door lock assembly.
17.
Using an ammeter:
INSPECT DRIVER’S DOOR (LHD)/PASSENGER’S
DOOR (RHD) PTC THERMISTOR OPERATION
(a)
Connect the positive (+) lead from the battery to terminal
3.
(b)
Connect the negative (–) lead from the ammeter to termi-
nal 4 and the positive (+) lead to battery positive (+) termi-
nal, and check that the current changes from approxi-
mately 3.2 A to less than 0.5 A within 20 to 70 seconds.
I19152
4
3
LOCK
UNLOCK
Door Lock Cable
I19151
2
1
LOCK
UNLOCK
Door Lock Cable
I19153
2
1
LOCK
UNLOCK
Door Lock Cable
I19154
6
2
LOCK
UNLOCK
Door Lock Cable
I19155
6
2
LOCK
UNLOCK
Door Lock Cable
–
BODY ELECTRICAL
POWER DOOR LOCK CONTROL SYSTEM
BE–101
LEXUS RX300 (RM785E)
(c)
Disconnect the leads from terminals.
(d)
Approximately 60 seconds later, connect the positive (+)
lead from the battery to terminal 3 and the negative (–)
lead to terminal 4, and check that the door lock cable
moves to the LOCK position.
If operation is not as specified, replace the door lock assembly.
18.
Using an ammeter:
INSPECT PASSENGER’S DOOR (LHD)/DRIVER’S
DOOR (RHD) PTC THERMISTOR OPERATION
(a)
Connect the negative (–) lead from the battery to terminal
1.
(b)
Connect the negative (–) lead from the ammeter to termi-
nal 2 and the positive (+) lead to battery positive (+) termi-
nal, and check that the current changes from approxi-
mately 3.2 A to less than 0.5 A within 20 to 70 seconds.
(c)
Disconnect the leads from terminals.
(d)
Approximately 60 seconds later, connect the positive (+)
lead from the battery to terminal 1 and the negative (–)
lead to terminal 2, and check that the door lock moves to
the LOCK position.
If operation is not as specified, replace the door lock cable as-
sembly.
19.
Using an ammeter:
INSPECT REAR DOOR PTC THERMISTOR OPERA-
TION
(a)
Connect the negative (–) lead from the battery to terminal
6.
(b)
Connect the negative (–) lead from the ammeter to termi-
nal 2 and the positive (+) lead to battery positive (+) termi-
nal, and check that the current changes from approxi-
mately 3.2 A to less than 0.5 A within 20 to 70 seconds.
(c)
Disconnect the leads from terminals.
(d)
Approximately 60 seconds later, connect the positive (+)
lead from the battery to terminal 6 and the negative (–)
lead to terminal 2, and check that the door lock cable
moves to the LOCK position.
If operation is not as specified, replace the door lock assembly.
I07314
UNLOCK
3
2
I07316
LOCK
3
2
I19156
3
4
LOCK
UNLOCK
Door Lock Cable
I19152
4
3
LOCK
UNLOCK
Door Lock Cable
I19157
1
2
LOCK
UNLOCK
Door Lock Cable
BE–102
–
BODY ELECTRICAL
POWER DOOR LOCK CONTROL SYSTEM
LEXUS RX300 (RM785E)
20.
Using an ammeter:
INSPECT BACK DOOR PTC THERMISTOR OPERA-
TION
(a)
Connect the negative (–) lead from the battery to terminal
2.
(b)
Connect the negative (–) lead from the ammeter to termi-
nal 3 and the positive (+) lead to battery positive (+) termi-
nal, and check that the current changes from approxi-
mately 3.2 A to less than 0.5 A within 20 to 70 seconds.
(c)
Disconnect the leads from terminals.
(d)
Approximately 60 seconds later, connect the positive (+)
lead from the battery to terminal 2 and the negative (–)
lead to terminal 3, and check that the door lock moves to
the LOCK position.
If operation is not as specified, replace the door lock assembly.
21.
Using an ammeter with a current–measuring probe:
INSPECT DRIVER’S DOOR (LHD)/PASSENGER’S
DOOR (RHD) PTC THERMISTOR OPERATION
(a)
Connect the positive (+) lead from the battery to terminal
4 and the negative (–) lead to terminal 3.
(b)
Attach a current–measuring probe to either the positive
(+) lead or the negative (–) lead, and check that the cur-
rent changes from approximately 3.2 A to less than 0.5 A
within 20 to 70 seconds.
(c)
Disconnect the leads from terminals.
(d)
Approximately 60 seconds later, connect the positive (+)
lead from the battery to terminal 3 and the negative (–)
lead to terminal 4, and check that the door lock cable
moves to the LOCK position.
If operation is not as specified, replace the door lock assembly.
22.
Using an ammeter with a current–measuring probe:
INSPECT PASSENGER’S DOOR (LHD)/DRIVER’S
DOOR (RHD) PTC THERMISTOR OPERATION
(a)
Connect the positive (+) lead from the battery to terminal
2 and the negative (–) lead to terminal 1.
(b)
Attach a current–measuring probe to either the positive
(+) lead or the negative (–) lead, and check that the cur-
rent changes from approximately 3.2 A to less than 0.5 A
within 20 to 70 seconds.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст