Lexus RX300 (MCU15). Service manual — part 465
B04134
N·m (kgf·cm, ft·lbf) : Specified torque
z
Non–reusable part
x 10
49.1 (500, 36)
z
Crankshaft Front
Oil Seal
Relief Valve
Spring
Plug
Oil Pump Body
Driven Rotor
Drive Rotor
Oil Pump Body Cover
–
LUBRICATION
OIL PUMP
LU–9
LEXUS RX300 (RM785E)
LU08L–02
A05607
P18778
Pivot
Bolt
Adjusting
Strut
Adjusting Bolt
B04135
P18801
LU–10
–
LUBRICATION
OIL PUMP
LEXUS RX300 (RM785E)
REMOVAL
HINT:
When repairing the oil pump, the oil pan and strainer should be
removed and cleaned.
1.
REMOVE OUTER COWL TOP PANEL
(See page EM–75)
2.
REMOVE FRONT UPPER SUSPENSION BRACE
(See page EM–75)
3.
DRAIN ENGINE OIL
4.
REMOVE RH FRONT WHEEL
5.
REMOVE RH FENDER APRON SEAL
6.
REMOVE ALTERNATOR FROM ENGINE
(See page CH–6)
7.
REMOVE A/C COMPRESSOR FROM ENGINE
(See page EM–75)
8.
REMOVE NO.2 FRONT EXHAUST PIPE
(See page EM–75)
9.
REMOVE WU–TWC
Remove the 2 nuts, WU–TWC and gasket.
10.
REMOVE PS PUMP DRIVE BELT AND ADJUSTING
STRUT
(a)
Loosen the pivot and adjusting bolts, and remove the
drive belt.
(b)
Remove the bolt, nut and adjusting strut.
11.
REMOVE TIMING BELT
(See page EM–16)
12.
REMOVE TIMING PULLEYS
(See page EM–16)
13.
REMOVE NO.3 TIMING BELT COVER
(See page EM–33)
14.
REMOVE A/C COMPRESSOR HOUSING
BRACKET
Remove the 2 bolts and housing bracket.
15.
REMOVE NO.2 OIL PAN
(a)
Remove the 10 bolts and 2 nuts.
P12716
SST
SST
P18802
B04136
B04137
P20050
Pry
–
LUBRICATION
OIL PUMP
LU–11
LEXUS RX300 (RM785E)
(b)
Insert the blade of SST between the No.1 and No.2 oil
pans, and cut off applied sealer and remove the No.1 oil
pan.
SST
09032–00100
NOTICE:
S
Be careful not to the damage the No.2 oil pan contact
surface of the No.1 oil pan.
S
Be careful not to damage the No.2 oil pan flange.
16.
REMOVE OIL STRAINER
Remove the bolt, 2 nuts, oil strainer and gasket.
17.
REMOVE NO.1 OIL PAN
(a)
Remove the 2 bolts and flywheel housing under cover.
(b)
Remove the 19 bolts.
(c)
Using a screwdriver, remove the oil pan by prying the por-
tions between the cylinder block and oil pan.
NOTICE:
Be careful not to damage the contact surfaces of the cylin-
der block and oil pan.
18.
REMOVE BAFFLE PLATE FROM NO.1 OIL PAN
19.
REMOVE CRANKSHAFT POSITION SENSOR
20.
REMOVE OIL PUMP
(a)
Remove the 9 bolts.
(b)
Remove the oil pump by prying a screwdriver between the
oil pump and main bearing cap.
(c)
Remove the O–ring.
LU04I–02
B04138
B04139
LU–12
–
LUBRICATION
OIL PUMP
LEXUS RX300 (RM785E)
DISASSEMBLY
1.
REMOVE RELIEF VALVE
Remove the plug, spring and relief valve.
2.
REMOVE DRIVE AND DRIVEN ROTORS
Remove the 10 screws, pump body cover, drive and driven ro-
tors.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст