Lexus RX300 (MCU15). Service manual — part 331
DI1RN–06
I04611
M6
DI–556
–
DIAGNOSTICS
SLIDING ROOF SYSTEM
LEXUS RX300 (RM785E)
TERMINALS OF ECU
Symbols (Terminals No.)
Wiring Color
Condition
STD Voltage (V)
B ↔ E
(M6–5 ↔ M6–7)
L–O ↔ W–B
Always
10 – 14 V
E ↔ Body ground
(M6–7 ↔ Body ground)
W–B ↔
Body Ground
Always
10 – 14 V
IG ↔ E
B R ↔ W B
Ignition switch ON
10 – 14 V
IG ↔ E
(M6–8 ↔ M6–7)
B–R ↔ W–B
Ignition switch OFF or ACC
Below 1 V
OPN ↔ E
P ↔ W B
Sliding roof control switch OPEN
10 – 14 V
OPN ↔ E
(M6–9 ↔ M6–7)
P ↔ W–B
Others
Below 1 V
CLS ↔ E
G Y ↔ W B
Sliding roof control switch CLOSE
10 – 14 V
CLS ↔ E
(M6–10 ↔ M6–7)
G–Y ↔ W–B
Others
Below 1 V
DI1RO–03
–
DIAGNOSTICS
SLIDING ROOF SYSTEM
DI–557
LEXUS RX300 (RM785E)
PROBLEM SYMPTOMS TABLE
Symptom
Suspect Area
See page
Sliding roof control system does not operate.
1. Sliding Roof Gear Assembly with ECU Circuit
2. Sliding Roof Control Switch Circuit
DI–558
DI–560
Sliding roof operates abnormally or stops half way.
1. Sliding Roof Limit Switch Circuit
DI–562
Jam protection system does not operate.
1. Sliding Roof Gear Assembly with ECU Circuit
DI–558
DI1RP–06
I07424
Battery
B–R
ALT
5
W
2
Instrument Panel J/B
AM1
1G
1
ID1
M6
L–O
5
W–L
3
4
B–Y
Ignition
Switch
Instrument Panel J/B
D
1H
1C
ECU–IG
7
1C
J4 J/C
13
8
IE
W–B
ID1
W–B
7
Sliding Roof Gear
Assembly with ECU
M6
M6
ID1
4
L–O
1A
8
6
1
S/ROOF
D
B–R
J5 J/C
B–R
8
W
B
IG
E
A
2
1
F11 FL BLOCK
DI–558
–
DIAGNOSTICS
SLIDING ROOF SYSTEM
LEXUS RX300 (RM785E)
CIRCUIT INSPECTION
Sliding Roof Gear Assembly with ECU Circuit
WIRING DIAGRAM
INSPECTION PROCEDURE
HINT:
If there is not the hand–held tester, replace sliding roof drive gear assembly.
1
Perform active test.
PREPARATION:
Connect the hand–held tester to the DLC3.
CHECK:
(a)
Enter into ACTIVE TEST function of hand–held tester.
(b)
Check that ”Slide roof motor” operates as the hand–held tester directs.
–
DIAGNOSTICS
SLIDING ROOF SYSTEM
DI–559
LEXUS RX300 (RM785E)
OK:
The motor operates normally.
NOTICE:
Caution is necessary not to be caught in as the jam protection system does not operate during con-
ducting ACTIVE TEST.
HINT:
With one ACTIVE direction, the sliding roof can be slidden and tilted continuously.
OK
Proceed to next circuit inspection shown on
problem symptom table (See page DI–557).
NG
Replace sliding roof drive gear assembly
(See page IN–32).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст