Lexus RX300 (MCU15). Service manual — part 411
FI0UT–01
B12939
Fuel
Tube
Fuel Tank Vent Tube
Set Plate
Fuel Pump Assembly
z
Gasket
X8
Clip
Outlet
4 (40,35 in.·lbf)
Fuel Pump & Sender
Gauge Connector
Floor Service Hole cover
Rear Seat Cushion
Fuel Filter
No.2 Fuel Suction Support
: Specified torque
z
Non–reusable part
N·m (kgf·cm, ft·lbf)
Fuel Suction
Plate with
Sender Gauge
Fuel Pressure
Regulator
Fuel
Pump
z
O–Ring
–
ELECTRONIC FUEL INJECTION
FUEL PRESSURE REGULATOR
FI–15
LEXUS RX300 (RM785E)
FUEL PRESSURE REGULATOR
COMPONENTS
FI0UU–01
B04948
Fuel
Pressure
Regulator
FI–16
–
ELECTRONIC FUEL INJECTION
FUEL PRESSURE REGULATOR
LEXUS RX300 (RM785E)
REMOVAL
1.
REMOVE FUEL PUMP ASSEMBLY FROM FUEL TANK
(See page FI–11)
2.
REMOVE NO. 2 FUEL SUCTION SUPPORT
(See page FI–11)
3.
REMOVE FUEL PRESSURE REGULATOR
(a)
Pull out the fuel pressure regulator.
(b)
Remove the O–ring from the fuel pressure regulator.
FI0UV–01
B00344
New O–Ring
–
ELECTRONIC FUEL INJECTION
FUEL PRESSURE REGULATOR
FI–17
LEXUS RX300 (RM785E)
INSTALLATION
1.
INSTALL FUEL PRESSURE REGULATOR
(a)
Install the O–ring to the fuel pressure regulator.
HINT:
Apply a light coat of gasoline to a new O–ring, and install it to
the fuel pressure regulator.
(b)
Connect the fuel pressure regulator from the fuel filter.
2.
INSTALL NO. 2 FUEL SUCTION SUPPORT
(See page FI–13)
3.
INSTALL FUEL PUMP ASSEMBLY FROM FUEL TANK
(See page FI–13)
A05071
5 mm
Hexagon
Wrench
FI0UW–01
B05296
Sound Scope
B05297
Ohmmeter
FI–18
–
ELECTRONIC FUEL INJECTION
INJECTOR
LEXUS RX300 (RM785E)
INJECTOR
ON–VEHICLE INSPECTION
1.
REMOVE V–BANK COVER
(a)
Using a 5 mm hexagon wrench, remove the 2 cap nuts.
(b)
Disconnect the 2 clips, and remove the V–bank cover.
2.
INSPECT INJECTOR OPERATION
Check operation sound from each injector.
(1)
With the engine running or cranking, use a sound
scope to check that there is normal operating noise
in proportion to engine speed.
(2)
If you have no sound scope, you can check the in-
jector operating vibration with your finger.
If no sound or unusual sound is heard, check the wiring connec-
tor, injector or injection signal from the engine ECU.
3.
INSPECT INJECTOR RESISTANCE
(a)
Disconnect the injector connector.
(b)
Using an ohmmeter, measure the resistance between the
terminals.
Resistance: 13.4 – 14.2 Ω at 20°C (68°F)
If the resistance is not as specified, replace the injector.
(c)
Reconnect the injector connector.
4.
REINSTALL V–BANK COVER
HINT:
For fixing the V–bank cover, push on the cover until a ”click” is
felt.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст