Lexus RX300 (MCU15). Service manual — part 562
SA042–04
F12953
181 (1,850, 134)
Rear Suspension Member
Retainer
83 (850, 61)
181 (1,850, 134)
Retainer
83 (850, 61)
Exhaust Center Pipe
and Exhaust Tailpipe
No. 2 Lower Suspension Arm
Toe–adjusting Cam
No. 1 Lower Suspension Arm
113 (1,150, 83)
113 (1,150, 83)
113 (1,150, 83)
Strut Rod
Parking Brake Cable
5.0 (51, 44 in.·lbf)
N·m (kgf·cm, ft·lbf) : Specified torque
z
Non–reusable part
177 (1,800, 131)
177 (1,800, 131)
62 (630, 46)
z
123 (1,250, 91)
SA–88
–
SUSPENSION AND AXLE
REAR LOWER SUSPENSION ARM AND STRUT ROD
LEXUS RX300 (RM785E)
REAR LOWER SUSPENSION ARM AND STRUT ROD
COMPONENTS
SA10Q–03
F04004
F04005
Matchmarks
F13601
–
SUSPENSION AND AXLE
REAR LOWER SUSPENSION ARM AND STRUT ROD
SA–89
LEXUS RX300 (RM785E)
REMOVAL
1.
REMOVE REAR WHEEL
Torque: 103 N·m (1,050 kgf·cm, 76 ft·lbf)
2.
REMOVE EXHAUST CENTER PIPE AND EXHAUST
TAILPIPE
Remove the 2 bolts, exhaust center pipe and exhaust tailpipe.
Torque: 62 N·m (630 kgf·cm, 46 ft·lbf)
3.
DISCONNECT PARKING BRAKE CABLE BRACKET
Remove the bolt and disconnect the parking brake bracket from
the body.
Torque: 5.0 N·m (51 kgf·cm, 44 in.·lbf)
4.
REMOVE STRUT ROD
Remove the 2 bolts, nuts and strut rod.
Torque:
Body side: 113 N·m (1,150 kgf·cm, 83 ft·lbf)
Carrier side: 123 N·m (1,250 kgf·cm, 91 ft·lbf)
HINT:
At the time of installation, after stabilizing the suspension,
torque the bolt.
5.
REMOVE NO. 2 LOWER SUSPENSION ARM
(a)
Place matchmarks on the toe–adjusting cam and suspen-
sion member.
(b)
Remove the bolt, nut and toe–adjusting cam and discon-
nect the No. 2 lower suspension arm from the rear sus-
pension member.
Torque: 113 N·m (1,150 kgf·cm, 83 ft·lbf)
(c)
Remove the bolt, nut and No. 2 lower suspension arm.
Torque: 177 N·m (1,800 kgf·cm, 131 ft·lbf)
HINT:
At the time of installation, after stabilizing the suspension,
torque the bolt.
6.
REMOVE NO. 1 LOWER SUSPENSION ARM
(a)
Remove the bolt and nut, and disconnect the No. 1 lower
suspension arm from the rear axle carrier.
Torque: 177 N·m (1,800 kgf·cm, 131 ft·lbf)
F04006
B
A
SA–90
–
SUSPENSION AND AXLE
REAR LOWER SUSPENSION ARM AND STRUT ROD
LEXUS RX300 (RM785E)
HINT:
At the time of installation, after stabilizing the suspension,
torque the bolt.
(b)
Loosen the No. 1 lower suspension arm rear suspension
member side set bolt.
Torque: 113 N·m (1,150 kgf·cm, 83 ft·lbf)
HINT:
S
Do not remove the bolt.
S
At the time of installation, after stabilizing the suspension,
torque the bolt.
(c)
Support the rear suspension member with a jack.
(d)
Remove the 4 nuts, 2 bolts and 2 retainers from the rear
suspension member.
Torque:
A: 83 N·m (850 kgf·cm, 61 ft·lbf)
B: 181 N·m (1,850 kgf·cm, 134 ft·lbf)
(e)
Lower the jack, remove the bolt, nut and No. 1 lower sus-
pension arm.
SA046–03
–
SUSPENSION AND AXLE
REAR LOWER SUSPENSION ARM AND STRUT ROD
SA–91
LEXUS RX300 (RM785E)
INSTALLATION
Installation is in the reverse order of removal (See page SA–89).
HINT:
After installation, check the rear wheel alignment (See page SA–8).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст