Lexus RX300 (MCU15). Service manual — part 272
FI1390
AB0119
H01002
H10600
H10598
D Squib
Spiral
Cable
Airbag
Sensor
Assembly
ON
DTC B0100/13
DLC3
→ ←
Tc
CG
DI–320
–
DIAGNOSTICS
SUPPLEMENTAL RESTRAINT SYSTEM
LEXUS RX300 (RM785E)
3
Check airbag sensor assembly.
PREPARATION:
(a)
Connect the connector to the airbag sensor assembly.
(b)
Connect negative (–) terminal cable to the battery, and
wait at least for 2 seconds.
CHECK:
(a)
Turn the ignition switch to ON and wait at least for 20 se-
conds.
(b)
Clear the DTC stored in memory (See page DI–305).
(c)
Turn the ignition switch to LOCK, and wait at least for 20
seconds.
(d)
Turn the ignition switch to ON, and wait at least for 20 se-
conds.
(e)
Check the DTC (See page DI–305).
OK:
DTC B0100/13 is not output.
HINT:
Codes other than code B0100/13 may be output at this time, but
they are not relevant to this check.
NG
Replace airbag sensor assembly.
OK
AB0119
FI1390
H01003
H10600
H10599
D Squib
Spiral
Cable
Airbag
Sensor
Assembly
ON
DTC B0100/13
DLC3
→
←
Tc
CG
–
DIAGNOSTICS
SUPPLEMENTAL RESTRAINT SYSTEM
DI–321
LEXUS RX300 (RM785E)
4
Check D squib.
PREPARATION:
(a)
Turn the ignition switch to LOCK.
(b)
Disconnect negative (–) terminal cable from the battery,
and wait at least for 90 seconds.
(c)
Connect the steering wheel pad connector.
(d)
Connect negative (–) terminal cable to the battery, and
wait at least for 2 seconds.
CHECK:
(a)
Turn the ignition switch to LOCK, and wait at least for 20
seconds.
(b)
Turn the ignition switch to ON, and wait at least for 20 se-
conds.
(c)
Clear the DTC stored in memory (See page DI–305).
(d)
Turn the ignition switch to LOCK, and wait at least for 20
seconds.
(e)
Turn the ignition switch to ON, and wait at least for 20 se-
conds.
(f)
Check the DTC (See page DI–305).
OK:
DTC B0100/13 is not output.
HINT:
Codes other than code B0100/13 may be output at this time, but
they are not relevant to this check.
NG
Replace steering wheel pad.
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check.
H01000
H02142
H02195
D Squib
Spiral
Cable
Airbag
Sensor
Assembly
D+
← →
(–)
(+)
D–
R14286
H01004
H01138
D Squib
Spiral
Cable
Airbag
Sensor
Assembly
D+
(–)
(+)
D–
DI–322
–
DIAGNOSTICS
SUPPLEMENTAL RESTRAINT SYSTEM
LEXUS RX300 (RM785E)
5
Check spiral cable.
PREPARATION:
(a)
Disconnect the connector between the airbag sensor as-
sembly and the spiral cable.
(b)
Release the airbag activation prevention mechanism of
the spiral cable connector on the airbag sensor assembly
side (See page DI–305).
CHECK:
For the connector (on the spiral cable side) between the spiral
cable and the steering wheel pad, measure the resistance be-
tween D+ and D–.
OK:
Resistance: 1 MΩ or Higher
NG
Repair or replace spiral cable.
OK3
6
Check harness between airbag sensor assembly and spiral cable.
PREPARATION:
Release the airbag activation prevention mechanism of the
connector (on the airbag sensor assembly side) between the
airbag sensor assembly and the spiral cable (See page
DI–305).
CHECK:
For the connector (on the spiral cable side) between the airbag
sensor assembly and the spiral cable, measure the resistance
between D+ and D–.
OK:
Resistance: 1 MΩ or Higher
NG
Repair or replace harness or connector be-
tween airbag sensor assembly and spiral cable.
OK
From the results of the above inspection, the malfunctioning part can now be considered normal.
To make sure of this, use the simulation method to check.
H01001
H02142
H02196
D Squib
Spiral
Cable
Airbag
Sensor
Assembly
D+
(–)
(+)
D–
← →
–
DIAGNOSTICS
SUPPLEMENTAL RESTRAINT SYSTEM
DI–323
LEXUS RX300 (RM785E)
DTC
B0101/14
Open in D Squib Circuit
CIRCUIT DESCRIPTION
The D squib circuit consists of the airbag sensor assembly, spiral cable and steering wheel pad.
It causes the airbag to deploy when the airbag deployment conditions are satisfied.
For details of the function of each component, see OPERATION on page RS–2.
DTC B0101/14 is recorded when an open is detected in the D squib circuit.
DTC No.
DTC Detecting Condition
Trouble Area
B0101/14
S Open circuit in D+ wire harness or D– wire harness of
squib
S D squib malfunction
S Spiral cable malfunction
S Airbag sensor assembly malfunction
S Steering wheel pad (D squib)
S Spiral cable
S Airbag sensor assembly
S Wire harness
WIRING DIAGRAM
See page DI–318.
INSPECTION PROCEDURE
1
Prepare for inspection (See step 1 on page DI–431).
2
Check D squib circuit.
CHECK:
For the connector (on the spiral cable side) between the spiral
cable and the steering wheel pad, measure the resistance be-
tween D+ and D–.
OK:
Resistance: Below 1 Ω
NG
Go to step 5.
OK
DI6P4–06
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст