Lexus RX300 (MCU15). Service manual — part 125
I19168
Engine Room J/B
D DOME Fuse
Vanity Light
Vanity Light
Door Courtesy
Light
Glove Compartment
Door Courtesy Light
Glove Compartment
Door Courtesy Switch
Front Personal Light
Door Courtesy Switch
Door Courtesy Light
Front Interior Light
Rear Interior Light
Door Courtesy Switch
Back Door Courtesy Switch
BE057–05
–
BODY ELECTRICAL
INTERIOR LIGHT SYSTEM
BE–47
LEXUS RX300 (RM785E)
INTERIOR LIGHT SYSTEM
LOCATION
BE1YI–01
N21585
2 1
N21586
Wire Harness Side
1
2
N20157
2
Ohmmeter
N20158
2
1
Ohmmeter
Z05672
Wire Harness Side
1
2
GA–2–1–B
BE–48
–
BODY ELECTRICAL
INTERIOR LIGHT SYSTEM
LEXUS RX300 (RM785E)
INSPECTION
1.
INSPECT PERSONAL LIGHT SWITCH CONTINUITY
Switch position
Tester connection
Specified condition
OFF
–
No continuity
ON
1 – 2
Continuity
If continuity is not as specified, replace the light assembly or
bulb.
2.
INSPECT PERSONAL LIGHT SWITCH CIRCUIT
Disconnect the connector from the switch and inspect the con-
nector on the wire harness side.
Tester connection
Condition
Specified condition
2 – Ground
Constant
Continuity
1 – Ground
Constant
Battery voltage
If the circuit is as specified, inspect power source or wire har-
ness.
3.
INSPECT INTERIOR LIGHT SWITCH
(a)
Disconnect the connector from the dome lamp.
(b)
Turn the dome lamp switch ON, check that continuity ex-
ists between terminal 2 and body ground.
(c)
Turn the dome lamp switch DOOR, check that there is
continuity exists between terminal 1 and 2.
If operation is not as specified, replace the switch.
4.
INSPECT INTERIOR LIGHT SWITCH CIRCUIT
Disconnect the connector from the switch and inspect the con-
nector on the wire harness side.
Tester connection
Condition
Specified condition
2 – Ground
Constant
Battery voltage
If the circuit is not as specified, inspect power source or wire
harness.
N17456
ON
OFF
2 1
N21587
Wire Harness Side
1 2
h–2–1–B
I19171
Open
Close
I19172
Wire Harness Side
I19173
Open
Close
–
BODY ELECTRICAL
INTERIOR LIGHT SYSTEM
BE–49
LEXUS RX300 (RM785E)
5.
INSPECT VANITY LIGHT CONTINUITY
Switch position
Tester connection
Specified condition
OFF (Closed)
–
No continuity
ON (Opened)
1 – 2
Continuity
If continuity is not as specified, replace the bulb or vanity light.
6.
INSPECT VANITY LIGHT SWITCH CIRCUIT
Disconnect the connector from the switch and inspect the con-
nector on the wire harness side.
Tester connection
Condition
Specified condition
2 – Ground
Constant
Continuity
1 – Ground
Constant
Battery voltage
If the circuit is not as specified, inspect power source or wire
harness.
7.
INSPECT FRONT DOOR COURTESY SWITCH CONTI-
NUITY
(a)
Check that continuity exists between terminals 10 and 11
with the door lock open.
(b)
Check that no continuity exists between terminals 10 and
11 with the door lock closed.
If operation is not as specified, replace the door lock.
8.
INSPECT FRONT DOOR COURTESY SWITCH CIR-
CUIT
Disconnect the connector from the door lock assembly and
inspect the connector on the wire harness side.
Tester connection
Condition
Specified condition
10 – 11
Constant
Battery voltage
If the circuit is not as specified, inspect power source or wire
harness.
9.
INSPECT REAR DOOR COURTESY SWITCH CONTI-
NUITY
(a)
Check that continuity exists between terminals 1 and 5
with the door lock open.
(b)
Check that no continuity exists between terminals 1 and
5 with the door lock closed.
If operation is not as specified, replace the door lock.
I19174
Wire Harness Side
N21589
1
2
N21590
Wire Harness Side
e–2–1
1
2
I04052
2
1
BE–50
–
BODY ELECTRICAL
INTERIOR LIGHT SYSTEM
LEXUS RX300 (RM785E)
10.
INSPECT REAR DOOR COURTESY SWITCH CIRCUIT
Disconnect the connector from the door lock assembly and in-
spect the connector on the wire harness side.
Tester connection
Condition
Specified condition
2 – 5
Constant
Battery voltage
If the circuit is not as specified, inspect power source or wire
harness.
11.
INSPECT BACK DOOR COURTESY SWITCH CONTI-
NUITY
Switch position
Tester connection
Specified condition
Switch OFF
–
No continuity
Switch ON
2 – Body Ground
Continuity
If continuity is not as specified, replace the switch and motor.
12.
INSPECT BACK DOOR COURTESY SWITCH CIRCUIT
Disconnect the connector from the switch and opener motor,
and inspect the connector on the wire harness side.
Tester connection
Condition
Specified condition
1 – Ground
Luggage compartment door opener switch OFF
No voltage
1 – Ground
Luggage compartment door opener switch ON
Battery voltage
2 – Ground
Constant
Battery voltage
If the circuit is not as specified, inspect power source or wire
harness.
13.
INSPECT DOOR COURTESY LIGHT CONTINUITY
Using the ohmmeter, check that there is continuity between ter-
minals.
If continuity is not as specified, replace the light assembly or
bulb.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст