Lexus RX300 (MCU15). Service manual — part 111
D03155
D03170
D07893
D07892
Raise
D03151
AX–28
–
AUTOMATIC TRANSAXLE
FLOOR SHIFT ASSEMBLY
LEXUS RX300 (RM785E)
12.
INSTALL SHIFT LEVER KNOB COVER
(a)
Install the O/D main switch to the shift lever knob cover.
(b)
Install the screw and shift lever knob cover.
Torque: 1.3 N·m (14 kgf·cm, 12 in.·lbf)
13.
INSTALL SHIFT LEVER KNOB BUTTON AND COM-
PRESSION SPRING
14.
INSTALL SHIFT LEVER KNOB AND SHIFT LEVER
KNOB COVER
(a)
Pass through the wire harness of the O/D main switch as
shown illustration and set it.
(b)
Install the shift lever knob and shift lever knob cover to the
shift lever sub–assembly.
NOTICE:
When operating the shift lever sub–assembly, check that
excessive force is not applied to the wire harness of the
O/D main switch.
15.
INSTALL 2 SHIFT LEVER SUB–ASSEMBLY SET
SCREWS
(a)
Install the 2 shift lever sub–assembly set screws.
Torque: 2.2 N·m (22 kgf·cm, 19 in.·lbf)
(b)
Raise the shift lever knob cover.
16.
CONNECT O/D MAIN SWITCH TERMINAL
(a)
Connect the terminals of the O/D main switch.
(b)
Connect the O/D main switch connector to the No.2 shift
lever plate.
17.
INSTALL SHIFT LEVER PLATE
Install the 4 bolts, nut and shift lever plate sub–assembly.
Torque: 5.7 N·m (58 kgf·cm, 50 in.·lbf)
AX09U–06
F00693
With the brake pedal depressed,
shift while holding the shift lever
knob button in. (The ignition switch
must be in ON position.)
Shift normally
Shift while holding the shift
lever knob button in.
–
AUTOMATIC TRANSAXLE
FLOOR SHIFT ASSEMBLY
AX–29
LEXUS RX300 (RM785E)
INSTALLATION
Installation is in the reverse order of removal
(See page AX–21).
HINT:
After installation, inspect shift lever operation.
S
When shifting it to each position, make sure that the shift-
ing lever moves smoothly, can be moderately operated
and the position indicator displays correctly.
Positions which can be operated without pressing
the shift lever knob button
R → N → D, L → 2 → D → N
Positions which can be operated only with pressing
the shift lever knob button
2 → L, N → R → P
Positions which can be operated only with pressing
the shift lever knob button, ignition switch ON and
brake pedal depressed
P → R
S
When starting the engine, make sure that the vehicle
moves forward when shifting from N to D range, and
moves rearward when shifting to R range.
AX11E–01
D02821
Wire Harness and Connector
Ground Cable
RH Stiffener Plate
RH Exhaust
Manifold Stay
34 (350, 25)
Transaxle
Plug for Line Pressure Test
x 5
Ground Cable
46 (470, 34)
8 (82, 71 in.·lbf)
37 (380, 27)
Flywheel Housing Under Cover
LH Exhaust Manifold Stay
Starter
39 (400, 29)
N·m (kgf·cm, ft·lbf)
: Specified torque
37 (380, 27)
37 (380, 27)
66 (670, 48)
37 (380, 27)
48 (490, 35)
8 (82, 71 in.·lbf)
20 (200, 14)
39 (400, 29)
AX–30
–
AUTOMATIC TRANSAXLE
AUTOMATIC TRANSAXLE UNIT
LEXUS RX300 (RM785E)
AUTOMATIC TRANSAXLE UNIT
COMPONENTS
AX11F–01
D02822
D02823
D02824
D02825
D02827
–
AUTOMATIC TRANSAXLE
AUTOMATIC TRANSAXLE UNIT
AX–31
LEXUS RX300 (RM785E)
REMOVAL
1.
REMOVE TRANSAXLE WITH ENGINE
(See page EM–71)
2.
REMOVE STARTER
(a)
Disconnect the starter wire and connector from the start-
er.
(b)
Remove the 2 bolts and starter.
Torque: 39 N·m (400 kgf·cm, 29 ft·lbf)
3.
REMOVE LH EXHAUST MANIFOLD STAY
Remove the bolt, nut and stay.
Torque:
Bolt: 20 N·m (200 kgf·cm, 14 ft·lbf)
Nut: 8 N·m (82 kgf·cm, 71 in.·lbf)
4.
REMOVE RH EXHAUST MANIFOLD STAY
Remove the bolt, nut and stay.
Torque: 34 N·m (350 kgf·cm, 25 ft·lbf)
5.
REMOVE RH STIFFENER PLATE
Remove the 5 bolts and RH stiffener plate.
Torque: 37 N·m (380 kgf·cm, 27 ft·lbf)
6.
REMOVE FLYWHEEL HOUSING UNDER COVER
Remove the 2 bolts and flywheel housing under cover.
Torque: 8 N·m (82 kgf·cm, 71 in.·lbf)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст