Chrysler Voyager. Manual — part 230
TEST
ACTION
APPLICABILITY
4
With the DRBIII
t, erase DTC’s.
Cycle the ignition switch from off to on and wait approximately 1 minute.
With the DRBIII
t, read DTC’s.
Did this DTC reset?
All
Yes
→ Replace the Body Control Module in accordance with the service
information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
347
COMMUNICATION
MIC MESSAGES NOT RECEIVED —
Continued
Symptom:
MSM MESSAGES NOT RECEIVED
When Monitored and Set Condition:
MSM MESSAGES NOT RECEIVED
When Monitored:
With the ignition in run, and the IOD fuse installed.
Set Condition:
The BCM does not receive any messages from the Memory Seat Module
(MSM) for at least 0.125 seconds.
POSSIBLE CAUSES
ATTEMPT TO COMMUNICATE WITH THE MEMORY SEAT MODULE
BODY CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRB, enter Body then Memory Seat Module.
Was the DRB able to I/D or communicate with the MSM?
All
Yes
→ Go To 2
No
→ Refer to the Communication category for the related symptom(s).
Perform BODY VERIFICATION TEST - VER 1.
2
With the DRB, erase DTC’s.
Cycle the ignition switch from off to on and wait approximately 1 minute.
With the DRB, read DTC’s.
Did this DTC reset?
All
Yes
→ Replace the Body Control Module in accordance with the service
information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
348
COMMUNICATION
Symptom:
NO PCI MESSAGES FROM CD CHANGER
When Monitored and Set Condition:
NO PCI MESSAGES FROM CD CHANGER
When Monitored:
With the ignition on and the radio on.
Set Condition:
If the DRB interrogates the CD Changer and does not receive the proper
response from the CD Changer.
POSSIBLE CAUSES
CD CHANGER (DIN) CABLE
CD CHANGER PCI BUS CIRCUIT OPEN
IGNITION SWITCH OUTPUT CIRCUIT OPEN
RADIO GROUND CKT OPEN
CD CHANGER
TEST
ACTION
APPLICABILITY
1
Turn the ignition off.
Disconnect the Radio C2 connector (DIN cable) from the Radio and the CD Changer.
Visually inspect the cable for damage.
In the next step check for open wires in the DIN cable.
Measure the resistance of the each DIN cable circuit between the Radio DIN cable
connector and the CD Changer DIN cable connector.
In the next step check for wires shorted to the DIN cable metal connectors.
Measure the resistance between each Radio C2 connector ( DIN cable) circuit and the
Radio Din cable metal connector.
Is the DIN cable circuits shorted together or open?
All
Yes
→ Replace the CD Changer (DIN) cable.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 2
349
COMMUNICATION
TEST
ACTION
APPLICABILITY
2
Use Scope input cable CH7058, Cable to Probe adapter CH7062, and the red and
black test probes.
Connect the scope input cable to the channel one connector on the DRB. Attach the
red and black leads and the cable to probe adapter to the scope input cable.
With the DRBIII
t select Pep Module Tools.
Select lab scope.
Select Live Data.
Select 12 volt square wave.
Press F2 for Scope.
Press F2 and use the down arrow to set voltage range to 20 volts. Set Probe to x10.
Press F2 again when complete.
Disconnect the CD Changer harness connector (DIN cable).
Connect the Black lead to the chassis ground. Connect the Red lead to the PCI Bus
circuit in the CD Changer DIN Cable connector.
Reconnect the Radio C2 (DIN Cable) harness connector.
Turn the ignition on.
Turn the Radio and CD Changer on.
Observe the voltage display on the DRB Lab Scope.
Does the voltage pulse from 0 to approximately 7.5 volts?
All
Yes
→ Go To 3
No
→ Replace the Radio.
Perform BODY VERIFICATION TEST - VER 1.
3
Turn the ignition off.
Disconnect the CD Changer harness connector (DIN cable).
Turn the ignition on.
Turn the Radio and the CD Changer on.
Using a 12-volt test light connected to ground, probe the Ignition Switch Output
circuit in the CD Changer DIN Cable connector.
Is the test light illuminated?
All
Yes
→ Go To 4
No
→ Replace the Radio.
Perform BODY VERIFICATION TEST - VER 1.
4
Turn the ignition off.
Disconnect the CD Changer harness connector (DIN cable).
Using a 12-volt test light connected to 12-volts, probe each CD Changer ground
circuit in the CD Changer connector (DIN cable).
Is the test light illuminated for each circuit?
All
Yes
→ Go To 5
No
→ Replace the Radio.
Perform BODY VERIFICATION TEST - VER 1.
5
If there are no possible causes remaining, view repair.
All
Repair
Replace the CD Changer.
Perform BODY VERIFICATION TEST - VER 1.
350
COMMUNICATION
NO PCI MESSAGES FROM CD CHANGER —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст