Chrysler Voyager. Manual — part 307
Symptom:
RIGHT TURN SIGNAL INDICATOR OPEN (HIGHLINE)
When Monitored and Set Condition:
RIGHT TURN SIGNAL INDICATOR OPEN (HIGHLINE)
When Monitored:
With the ignition on.
Set Condition:
The BCM detects an open in the Right Turn Indicator Driver.
POSSIBLE CAUSES
INTERMITTENT CONDITION
FUSED B+ CIRCUIT
MESSAGE CENTER OPERATION
RIGHT TURN INDICATOR DRIVER SHORTED TO GROUND
RIGHT TURN INDICATOR DRIVER OPEN
BCM
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
Monitor the Right Turn Signal Indicator.
Operate the Right Turn Signal.
Is the Indicator lamp operating correctly?
All
Yes
→ Go To 2
No
→ Go To 3
2
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running at normal operating temperature, monitor the DRB
parameters related to the DTC while wiggling the wiring harness. Look for param-
eter values to change and/or a DTC to set.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?
All
Yes
→ Repair as necessary
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
655
INSTRUMENT CLUSTER
TEST
ACTION
APPLICABILITY
3
Turn the ignition off.
Disconnect the Message Center harness connector.
Turn the ignition on.
Using a 12-volt test light connected to ground, probe the Fused B+ circuit in the
Message Center harness connector.
Does the test light illuminate brightly?
All
Yes
→ Go To 4
No
→ Repair the Fused B+ circuit.
Perform BODY VERIFICATION TEST - VER 1.
4
Turn the ignition off.
Disconnect the Message Center harness connector.
Turn the ignition on.
Using a 12-volt test light connected to 12-volts, probe the Right Indicator Driver
circuit in the Message Center harness connector.
Operate the Multi-Function Switch and turn the Right Indication on.
Does the test light flash on and off?
All
Yes
→ Remove and inspect the Bulb. If OK, replace the Message Center.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 5
5
Turn the ignition off.
Disconnect the Message Center harness connector.
Disconnect the BCM C4 harness connector.
Measure the resistance of the Right Turn Indicator Driver circuit at the Message
Center harness connector to ground.
Is the resistance below 5.0 ohms?
All
Yes
→ Repair the Right Turn Indicator for a short to ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 6
6
Turn the ignition off.
Disconnect the Message Center harness connector.
Disconnect the BCM C4 harness connector.
Measure the resistance of the Right Turn Indicator Driver circuit between the BCM
harness connector and the Message Center harness connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 7
No
→ Repair the Right Turn Indicator for an open.
Perform BODY VERIFICATION TEST - VER 1.
7
If there are no possible causes remaining, view repair?
All
Repair
Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.
656
INSTRUMENT CLUSTER
RIGHT TURN SIGNAL INDICATOR OPEN (HIGHLINE) —
Continued
Symptom:
RIGHT TURN SIGNAL INDICATOR OPEN (LOWLINE)
When Monitored and Set Condition:
RIGHT TURN SIGNAL INDICATOR OPEN (LOWLINE)
When Monitored:
With the ignition on.
Set Condition:
The BCM detects an open in the Right Turn Indicator Driver.
POSSIBLE CAUSES
RIGHT TURN INDICATOR DRIVER SHORTED TO GROUND
INTERMITTENT CONDITION
FUSED B+ CIRCUIT
INSTRUMENT CLUSTER OPERATION
RIGHT TURN INDICATOR DRIVER OPEN
BCM
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
Monitor the Right Turn Signal Indicator.
Operate the Right Turn Signal.
Is the Indicator lamp operating correctly?
All
Yes
→ Go To 2
No
→ Go To 3
2
WARNING: WHEN THE ENGINE IS OPERATING, DO NOT STAND IN A
DIRECT LINE WITH THE FAN. DO NOT PUT YOUR HANDS NEAR THE
PULLEYS, BELTS OR FAN. DO NOT WEAR LOOSE CLOTHING.
NOTE: The conditions that set the DTC are not present at this time. The
following list may help in identifying the intermittent condition.
With the engine running at normal operating temperature, monitor the DRB
parameters related to the DTC while wiggling the wiring harness. Look for param-
eter values to change and/or a DTC to set.
Refer to any Technical Service Bulletins (TSB) that may apply.
Visually inspect the related wiring harness. Look for any chafed, pierced, pinched, or
partially broken wires.
Visually inspect the related wiring harness connectors. Look for broken, bent, pushed
out, or corroded terminals.
Were any of the above conditions present?
All
Yes
→ Repair as necessary
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
657
INSTRUMENT CLUSTER
TEST
ACTION
APPLICABILITY
3
Turn the ignition off.
Disconnect the Instrument Cluster harness connector.
Turn the ignition on.
Using a 12-volt test light connected to ground, probe the Fused B+ circuit in the
Instrument Cluster harness connector.
Does the test light illuminate brightly?
All
Yes
→ Go To 4
No
→ Repair the Fused B+ circuit.
Perform BODY VERIFICATION TEST - VER 1.
4
Turn the ignition off.
Disconnect the Instrument Cluster harness connector.
Turn the ignition on.
Using a 12-volt test light connected to 12-volts, probe the Right Indicator Driver
circuit in the Instrument Cluster harness connector.
Operate the Multi-Function Switch and turn the Right Indication on.
Does the test light flash on and off?
All
Yes
→ Remove and inspect the Bulb. If OK, replace the Instrument
Cluster printed circuit board.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 5
5
Turn the ignition off.
Disconnect the Instrument Cluster harness connector.
Disconnect the BCM C4 harness connector.
Measure the resistance of the Right Turn Indicator Driver circuit between the BCM
harness connector and the Instrument Cluster harness connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 6
No
→ Repair the Right Turn Indicator for an open.
Perform BODY VERIFICATION TEST - VER 1.
6
Turn the ignition off.
Disconnect the Instrument Cluster harness connector.
Disconnect the BCM C4 harness connector.
Measure the resistance of the Right Turn Indicator Driver circuit at the Instrument
Cluster harness connector to ground.
Is the resistance below 5.0 ohms?
All
Yes
→ Repair the Right Turn Indicator for a short to ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 7
7
If there are no possible causes remaining, view repair?
All
Repair
Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.
658
INSTRUMENT CLUSTER
RIGHT TURN SIGNAL INDICATOR OPEN (LOWLINE) —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст