Chrysler Voyager. Manual — part 391
Symptom:
REAR WASH SWITCH INPUT STUCK
When Monitored and Set Condition:
REAR WASH SWITCH INPUT STUCK
When Monitored:
Ignition ON
Set Condition:
Switch is applied for more than 10 seconds.
POSSIBLE CAUSES
REAR WASHER SWITCH STUCK
INTERMITTENT WIRING AND CONNECTORS
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRB, select Body, Body Control Module and read the R Washer Switch
state.
Does the DRB display switch state as Closed?
All
Yes
→ Go To 2
No
→ Go To 3
2
Turn the ignition off.
Disconnect the Rear Washer Switch harness connector.
Turn the ignition on.
With the DRB, select Body, Body Control Module and read the R Washer Switch
state.
Does the DRB display switch state as Open?
All
Yes
→ Replace the Rear Washer Switch in accordance with the Service
Information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 3
3
Turn the ignition on.
With the DRBIII
t, erase all BCM and FCM DTCs.
Turn the ignition off.
The conditions necessary to set this DTC are not present at this time.
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
Were there any problems found?
All
Yes
→ Repair as necessary.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
991
WINDSHIELD WIPER & WASHER
Symptom:
REAR WASHER OUTPUT OPEN
When Monitored and Set Condition:
REAR WASHER OUTPUT OPEN
When Monitored:
Ignition on.
Set Condition:
POSSIBLE CAUSES
INTERMITTENT WIRING AND CONNECTORS
FUSED ACCESSORY RELAY OUTPUT CIRCUIT
REAR WASHER MOTOR CONTROL CIRCUIT OPEN
REAR WASHER MOTOR CONTROL CIRCUIT SHORT TO VOLTAGE
REAR WASHER PUMP MOTOR
FRONT CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
Ignition on, engine not running.
Press the Rear Washer Switch.
Does the Rear Washer Motor Function?
All
Yes
→ Go To 2
No
→ Go To 3
2
Turn the ignition on.
With the DRBIII
t, erase all BCM and FCM DTCs.
Turn the ignition off.
The conditions necessary to set this DTC are not present at this time.
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
Were there any problems found?
All
Yes
→ Repair as necessary.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
992
WINDSHIELD WIPER & WASHER
TEST
ACTION
APPLICABILITY
3
Turn the ignition off to the lock position.
Disconnect the Rear Washer Pump Motor harness connector.
Note: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
Using a 12-volt test light connected to ground, check the Fused Accessory Relay
Output circuit in the Rear Washer Pump Motor harness connector.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the test light illuminate brightly?
All
Yes
→ Go To 4
No
→ Repair the Fused Accessory Relay Output circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
4
Turn the ignition off to the lock position.
Disconnect the Rear Washer Pump Motor harness connector.
Note: Check connectors - Clean/repair as necessary.
Ignition on, engine not running.
Using a 12-volt test light connected to 12 Volts, check the Rear Washer Pump Motor
Control circuit in the Rear Washer Pump Motor harness connector while pressing the
Rear Washer Switch.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the test light illuminate brightly?
All
Yes
→ Replace the Rear Washer Pump Motor in accordance with the
Service Information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 5
5
Turn the ignition off to the lock position.
Disconnect the Front Control Module harness connector.
Disconnect the Rear Washer Pump Motor harness connector.
Note: Check connectors - Clean/repair as necessary.
Measure the resistance of the Rear Washer Pump Motor Control Circuit from the
Front Control Module connector to the Rear Washer Pump Motor harness connector.
Is the resistance above 5.0 ohms?
All
Yes
→ Repair the Rear Washer Pump Motor Control Circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 6
6
Turn the ignition off to the lock position.
Disconnect the Front Control Module connector.
Disconnect the Rear Washer Pump Motor harness connector.
Note: Check connectors - Clean/repair as necessary.
Turn the ignition on.
Using a 12-volt test light connected to ground, check the Rear Washer Pump Motor
Control circuit.
Does the test light illuminate brightly?
All
Yes
→ Repair the Rear Washer Pump Motor Control Circuit for a short
to voltage.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Front Control Module in accordance with the Service
Information.
Perform BODY VERIFICATION TEST - VER 1.
993
WINDSHIELD WIPER & WASHER
REAR WASHER OUTPUT OPEN —
Continued
Symptom:
REAR WIPER OUTPUT OPEN
When Monitored and Set Condition:
REAR WIPER OUTPUT OPEN
When Monitored:
Ignition on.
Set Condition:
The Output is ON, the Output Driver Status is LOW and there is no Park
signal.
POSSIBLE CAUSES
INTERMITTENT WIRING AND CONNECTORS
REAR WIPER MOTOR CONTROL CIRCUIT OPEN
REAR WIPER MOTOR GROUND OPEN
REAR WIPER MOTOR CONTROL CIRCUIT SHORT TO VOLTAGE
REAR WIPER MOTOR
BODY CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
Ignition on, engine not running.
Turn on the Rear Wiper.
Does the Rear Wiper Function?
All
Yes
→ Go To 2
No
→ Go To 3
2
Turn the ignition on.
With the DRBIII
t, erase all BCM and FCM DTCs.
Turn the ignition off.
The conditions necessary to set this DTC are not present at this time.
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
Were there any problems found?
All
Yes
→ Repair as necessary.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
994
WINDSHIELD WIPER & WASHER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст