Chrysler Voyager. Manual — part 253
Symptom:
BACKUP LAMP OUTPUT OPEN
When Monitored and Set Condition:
BACKUP LAMP OUTPUT OPEN
When Monitored:
Trans in reverse.
Set Condition:
Voltage output status is Low.
POSSIBLE CAUSES
INTERMITTENT CONDITION
GROUND CIRCUIT
BACKUP LAMP OPEN
BACKUP LAMP DRIVER CIRCUIT OPEN
BODY CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, clear all BCM, IPM DTC’s.
Actuate the Backup Lamps.
With the DRBIII
t, read the DTC information.
Does the DRBIII
t read: Backup Lamp Output Open?
All
Yes
→ Go To 2
No
→ The condition that caused the symptom is currently not present.
Inspect the related wiring for a possible intermittent condition.
Look for terminal push out or any chafed, pierced, pinched, or
partially broken wires.
Perform BODY VERIFICATION TEST - VER 1.
2
Turn the ignition off
Disconnect the inoperative rear tail lamp harness connector.
Using a 12-volt test light connected to 12-volts, check the ground circuit.
Does the test light illuminate brightly?
All
Yes
→ Go To 3
No
→ Repair the Ground Circuit.
Perform BODY VERIFICATION TEST - VER 1.
439
EXTERIOR LIGHTING
TEST
ACTION
APPLICABILITY
3
Turn the ignition off.
Disconnect the inoperative rear tail lamp harness connector.
Turn the ignition on.
Engage the transmission to reverse.
Using a 12-volt test light connected to ground, check the Backup Lamps Output
circuit.
Does the test light illuminate brightly?
All
Yes
→ Replace the applicable Backup Lamp.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 4
4
Turn the ignition off.
Disconnect the Body Control Module harness connector.
Disconnect the inoperative rear tail lamp harness connector.
Measure the resistance of the Backup Lamp Driver Circuit.
Is the resistance above 5.0 ohms?
All
Yes
→ Repair the Backup Lamp Driver Circuit for an open condition.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.
440
EXTERIOR LIGHTING
BACKUP LAMP OUTPUT OPEN —
Continued
Symptom:
BACKUP LAMP OUTPUT SHORT
When Monitored and Set Condition:
BACKUP LAMP OUTPUT SHORT
When Monitored:
With the transmission in reverse.
Set Condition:
When voltage output status is Low.
POSSIBLE CAUSES
INTERMITTENT CONDITION
BACKUP LAMP
BACKUP LAMP DRIVER CIRCUIT SHORT TO GROUND
BODY CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, clear all BCM DTC’s.
Place the transmission in reverse.
With the DRBIII
t, read the DTC information.
Does the DRBIII
t read: Backup Lamp Output Short?
All
Yes
→ Go To 2
No
→ The condition that caused the symptom is currently not present.
Inspect the related wiring for a possible intermittent condition.
Look for any chafed, pierced,pinched, or partially broken wires.
Perform BODY VERIFICATION TEST - VER 1.
2
Turn the ignition on.
Place the transmission in reverse.
Using a 12-volt test light connected to ground, check the Backup Lamp Output
circuit.
Does the test light illuminate brightly?
All
Yes
→ Replace the Backup Lamp.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 3
3
Turn the ignition off.
Disconnect the Body Control Module harness connector.
Disconnect both rear tail lamp harness connector.
Measure the resistance of the Backup Lamp Driver circuit and ground.
Is the resistance below 5.0 ohms?
All
Yes
→ Repair the Backup Lamp Driver circuit for a short to ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.
441
EXTERIOR LIGHTING
Symptom:
FRONT FOG LAMP RELAY OPEN
When Monitored and Set Condition:
FRONT FOG LAMP RELAY OPEN
When Monitored:
Ignition On.
Set Condition:
The IPM detects high current from the fog lamp relay control circuit.
POSSIBLE CAUSES
MISSING RELAY
OPEN FUSE
FOG LAMP RELAY
INTERMITTENT CONDITION
FOG LAMP RELAY CONTROL CIRCUIT OPEN
FRONT CONTROL MODULE
INTELLIGENT POWER MODULE
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, clear all IPM DTC’s.
Turn the Fog Lamps on.
With the DRBIII
t, read the DTC information.
Does the DRBIII
t read: Front Fog Lamp Relay Open?
All
Yes
→ Go To 2
No
→ Go To 5
2
Turn the ignition off.
Check the IPM to make certain the Fog Lamp Relay is present.
Is the Fog Lamp Relay present?
All
Yes
→ Go To 3
No
→ Replace the missing Fog Lamp Relay.
Perform BODY VERIFICATION TEST - VER 1.
3
Turn the ignition off.
Install a known good relay in place of the fog lamp relay.
Turn the Fog Lamps On.
Do the Fog Lamps operate normally?
All
Yes
→ Replace the Fog Lamp Relay.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 4
442
EXTERIOR LIGHTING
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст