Chrysler Voyager. Manual — part 270
TEST
ACTION
APPLICABILITY
4
Turn the ignition off.
Disconnect the Body Control Module C5 harness connector.
Disconnect the Multifunction Switch harness connector.
Measure the resistance between the Multifunction Switch MUX Return circuit and
the Turn Signal Switch MUX circuit.
Is the resistance below 5.0 ohms?
All
Yes
→ Repair the Turn Signal Switch MUX circuit for a short to the
Multifunction Switch MUX Return circuit.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 5
5
Turn the ignition off.
Disconnect the Body Control Module C5 harness connector.
Disconnect the Multifunction Switch harness connector.
Measure the resistance between the Multifunction Switch MUX Return circuit and
ground.
Is the resistance below 5.0 ohms?
All
Yes
→ Repair the Multifunction Switch MUX Return circuit for a short
to ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.
507
EXTERIOR LIGHTING
TURN SIGNAL SWITCH INPUT SHORT —
Continued
Symptom List:
A/C SWITCH FAULT (ACTIVE) - MTC
CHECKSUM FAILURE (ACTIVE) - MTC
DEFOG SWITCH FAULT (ACTIVE) - MTC
POWER SWITCH FAULT (ACTIVE) - MTC
RECIRC SWITCH FAULT (ACTIVE) - MTC
Test Note:
All symptoms listed above are diagnosed using the same tests.
The title for the tests will be A/C SWITCH FAULT (ACTIVE) -
MTC.
When Monitored and Set Condition:
A/C SWITCH FAULT (ACTIVE) - MTC
When Monitored:
With the ignition on.
Set Condition:
This DTC will set if the A/C switch stays closed for 10 minutes.
CHECKSUM FAILURE (ACTIVE) - MTC
When Monitored:
With the ignition on.
Set Condition:
This DTC will set if the calculated check sum does not match the stored
value.
DEFOG SWITCH FAULT (ACTIVE) - MTC
When Monitored:
With the ignition on.
Set Condition:
This DTC will set if the EBL switch stays closed for 10 minutes.
POWER SWITCH FAULT (ACTIVE) - MTC
When Monitored:
With the ignition on.
Set Condition:
This DTC will set if the Power switch stays closed for 10 minutes.
RECIRC SWITCH FAULT (ACTIVE) - MTC
When Monitored:
With the ignition on.
Set Condition:
This DTC will set if the Recirc switch stays closed for 10 minutes.
POSSIBLE CAUSES
A/C - HEATER CONTROL MODULE
508
HEATING & A/C
TEST
ACTION
APPLICABILITY
1
View repair
All
Repair
Replace the A/C - Heater Control Module in accordance with the
Service Information.
Perform BODY VERIFICATION TEST - VER 1.
509
HEATING & A/C
A/C SWITCH FAULT (ACTIVE) - MTC —
Continued
Symptom List:
A/C SWITCH FAULT (STORED) - MTC
BACKLIGHT DIMMING RX FAILURE (STORED) - MTC
BLEND OVERCURRENT (STORED) - MTC
CHECKSUM FAILURE (STORED) - MTC
DEFOG SWITCH FAULT (STORED) - MTC
EVAPORATOR
TEMPERATURE
SENSOR
CIRCUIT
OPEN
(STORED) - MTC
EVAPORATOR
TEMPERATURE
SENSOR
CIRCUIT
SHORT
(STORED) - MTC
LOOPBACK TEST FAILURE (STORED) - MTC
MODE OVERCURRENT (STORED) - MTC
NO FUEL LEVEL MESSAGE RECEIVED (STORED) - MTC
PCM COMMUNICATION FAILURE (STORED) - MTC
POWER SWITCH FAULT (STORED) - MTC
REAR BLEND OVERCURRENT (STORED) - MTC
REAR BLEND POT CIRCUIT OPEN (STORED) - MTC
REAR BLEND POT CIRCUIT SHORT (STORED) - MTC
REAR MODE OVERCURRENT (STORED) - MTC
RECIRC OVERCURRENT (STORED) - MTC
RECIRC SWITCH FAULT (STORED) - MTC
TX FAILURE (STORED) - MTC
VEHICLE ODOMETER FAILURE (STORED) - MTC
ZONE OVERCURRENT (STORED) - MTC
Test Note:
All symptoms listed above are diagnosed using the same tests.
The title for the tests will be A/C SWITCH FAULT (STORED) -
MTC.
When Monitored and Set Condition:
A/C SWITCH FAULT (STORED) - MTC
When Monitored:
With the ignition on.
Set Condition:
This DTC will set if the A/C switch stays closed for 10 minutes.
BACKLIGHT DIMMING RX FAILURE (STORED) - MTC
When Monitored:
With the ignition on.
Set Condition:
If the A/C - Heater Control Module does not receive the dimming function
message from the BCM for more than 5 seconds, then the A/C - Heater Control Module
LEDs will default to full brightness and the DTC will set.
510
HEATING & A/C
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст