Chrysler Voyager. Manual — part 319
Symptom:
MEMORY SWITCH INPUT OPEN
When Monitored and Set Condition:
MEMORY SWITCH INPUT OPEN
When Monitored:
Continuously when the PCI bus is active.
Set Condition:
If the Memory Set switch voltage is greater than 4.8 volts for over 10
seconds.
POSSIBLE CAUSES
DTC PRESENT
MEMORY SET SWITCH OPEN
MEMORY SELECT SWITCH MUX OPEN
MEMORY SELECT SWITCH RETURN OPEN
BODY CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, record and erase DTC’s.
Cycle the ignition OFF then back ON.
With the DRBIII
t, read DTCs.
Operate the Memory Set switch several times while monitoring the DRBIII.
Does the DRBIII
t display MEMORY SWITCH INPUT OPEN?
All
Yes
→ Go To 2
No
→ Using the wiring diagram/schematic as a guide, inspect the
wiring and connectors for an intermittent condition.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
2
Disconnect the Memory Set Switch connector
Turn the ignition on.
Connect a jumper wire between Memory Select Switch MUX and Memory Select
Switch Return.
With the DRBIII
t in Sensors, read the Memory Select SW Volts.
Is the voltage below 1.0 volt?
All
Yes
→ Replace the Memory Set Switch.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
No
→ Go To 3
703
MEMORY SEAT
TEST
ACTION
APPLICABILITY
3
Turn the ignition off.
Disconnect the Memory Set switch connector.
Disconnect the BCM C1 harness connector.
Measure the resistance of the Memory Select Switch MUX circuit between the
Memory Set Switch connector and the BCM C1 connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 4
No
→ Repair the Memory Select Switch MUX circuit for an open.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
4
Turn the ignition off.
Disconnect the Memory Set switch connector.
Disconnect the BCM C1 harness connector.
Measure the resistance of the Memory Select Switch Return circuit between the
Memory Set Switch connector and the BCM C1 connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 5
No
→ Repair the Memory Select Switch Return circuit for an open.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
5
If there are no possible causes remaining, view repair.
All
Repair
Replace the Body Control Module.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
704
MEMORY SEAT
MEMORY SWITCH INPUT OPEN —
Continued
Symptom:
MEMORY SWITCH INPUT SHORT
When Monitored and Set Condition:
MEMORY SWITCH INPUT SHORT
When Monitored:
Anytime the Body Control Module is awake.
Set Condition:
If the Memory Set switch voltage is less than 1.35 volts for over 10
seconds.
POSSIBLE CAUSES
DTC PRESENT
MEMORY SET SWITCH SHORTED
MEMORY SELECT SWITCH MUX SHORTED
BODY CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, record and erase DTC’s.
Cycle the ignition OFF then back ON.
With the DRBIII
t, read DTCs.
Operate the Memory Set switch several times while monitoring the DRBIII.
Does the DRBIII
t display MEMORY SWITCH INPUT SHORT?
All
Yes
→ Go To 2
No
→ Using the wiring diagram/schematic as a guide, inspect the
wiring and connectors for an intermittent condition.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
2
Disconnect the Memory Set Switch connector
Turn the ignition on.
With the DRBIII
t in Sensors, read the Memory Select SW Volts.
Is the voltage above 4.8 volts?
All
Yes
→ Replace the Memory Set Switch.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
No
→ Go To 3
3
Turn the ignition off.
Disconnect the Memory Set switch connector.
Disconnect the BCM C1 harness connector.
Measure the resistance between ground and the Memory Select Switch MUX circuit.
Is the resistance above 5.0 ohms?
All
Yes
→ Go To 4
No
→ Repair the Memory Select Switch MUX circuit for a short to
ground.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
705
MEMORY SEAT
TEST
ACTION
APPLICABILITY
4
If there are no possible causes remaining, view repair.
All
Repair
Replace the Body Control Module.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
706
MEMORY SEAT
MEMORY SWITCH INPUT SHORT —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст