Chrysler Voyager. Manual — part 154
STORED ENERGY FIRING 1
When Monitored:
With the ignition on, the module on board diagnostics continuously
performs internal circuit tests.
Set Condition:
This DTC will set if the module identifies an out of range internal circuit.
POSSIBLE CAUSES
AIRBAG CONTROL MODULE - ACM
SIDE IMPACT AIRBAG CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
NOTE: Ensure the battery is fully charged.
NOTE: For the purpose of this test, the AECM and ORC modules will be
referred to as an ACM.
WARNING: IF THE MODULE IS DROPPED AT ANY TIME, IT MUST BE
REPLACED.
Select the appropriate module and DTC type combination:
All
ACM - ACTIVE DTC
WARNING: TURN THE IGNITION OFF, DISCONNECT THE
BATTERY AND WAIT TWO MINUTES BEFORE PROCEEDING.
Replace the Airbag Control Module in accordance with Service
Manuals.
Perform AIRBAG VERIFICATION TEST - VER 1.
ACM - STORED DTC
WARNING: TURN THE IGNITION OFF, DISCONNECT THE
BATTERY AND WAIT TWO MINUTES BEFORE PROCEEDING.
Replace the Airbag Control Module in accordance with Service
Manuals.
Perform AIRBAG VERIFICATION TEST - VER 1.
SIACM - ACTIVE DTC
WARNING: TURN THE IGNITION OFF, DISCONNECT THE
BATTERY AND WAIT TWO MINUTES BEFORE PROCEEDING.
Replace the Side Impact Airbag Control Module in accordance
with Service Manuals.
Perform AIRBAG VERIFICATION TEST - VER 1.
SIACM - STORED DTC
WARNING: TURN THE IGNITION OFF, DISCONNECT THE
BATTERY AND WAIT TWO MINUTES BEFORE PROCEEDING.
Replace the Side Impact Airbag Control Module in accordance
with Service Manuals.
Perform AIRBAG VERIFICATION TEST - VER 1.
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
43
AIRBAG
ACCELEROMETER 1 —
Continued
Symptom List:
AIRBAG WARNING INDICATOR OPEN
AIRBAG WARNING INDICATOR SHORT
Test Note:
All symptoms listed above are diagnosed using the same tests.
The title for the tests will be AIRBAG WARNING INDICATOR
TEST.
When Monitored and Set Condition:
AIRBAG WARNING INDICATOR OPEN
When Monitored:
With ignition on the ACM monitors the PCI Bus for a message from the
MIC containing the airbag warning indicator status. The ACM request the warning lamp
status from the MIC once every second.
Set Condition:
This DTC will set immediately if the indicator status is OPEN.
AIRBAG WARNING INDICATOR SHORT
When Monitored:
With ignition on the ACM monitors the PCI Bus for a message from the
MIC containing the airbag warning indicator status. The ACM request the warning lamp
status from the MIC once every second.
Set Condition:
This DTC will set immediately if the indicator status is SHORT.
POSSIBLE CAUSES
MIC, COMMUNICATION FAILURE
WARNING INDICATOR
ACM, WARNING INDICATOR
STORED CODE OR INTERMITTENT CONDITION
ACTIVE CODE PRESENT
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
Ensure the battery is fully charged.
NOTE: For the purpose of this test, the AECM and ORC modules will be
referred to as an ACM.
SELECT ACTIVE or STORED DTC:
All
ACM - ACTIVE DTC
ACM - STORED DTC
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
44
AIRBAG
TEST
ACTION
APPLICABILITY
2
With the DRBIII
t, ensure PCI Bus communications with the Instrument Cluster.
Is the Instrument Cluster communicating on the PCI Bus?
All
Yes
→ Go To 3
No
→ Refer to category COMMUNICATION CATEGORY and select the
related symptom NO RESPONSE or INSTRUMENT CLUSTER
BUS +/- SIGNAL OPEN.
3
With the DRBIII
t select PASSIVE RESTRAINTS, AIRBAG and MONITOR DIS-
PLAY.
Using the DRBIII
t, read the WARNING LAMP MONITOR screen.
Select the LAMP STATUS displayed on the DRB monitors screen.
Observe the Lamp Driver State and Actual lamp
Is the LAMP DRIVER and ACTUAL LAMP STATE: OK?
All
YES
NO
Replace Instrument Cluster.
Perform AIRBAG VERIFICATION TEST - VER 1.
4
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
If there are no possible causes remaining, view repair.
All
Repair
Replace the Airbag Control Module in accordance with Service
Manuals. WARNING: IF THE AIRBAG CONTROL MODULE
IS DROPPED AT ANY TIME, IT MUST BE REPLACED.
Perform AIRBAG VERIFICATION TEST - VER 1.
5
With the DRBIII
t, record and erase all DTC’s from all Airbag modules.
If equipped with Passenger Airbag On - Off switch, read the DTC’s in all switch
positions.
If any ACTIVE codes are present they must be resolved before diagnosing any stored
codes.
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Look for chaffed, pierced, pinched, or partially broken wires and broken, bent, pushed
out, spread, corroded, or contaminated terminals.
The following additional checks may assist you in identifying a possible intermittent
problem.
Reconnect any disconnected components and harness connector.
WARNING: TURN THE IGNITION ON, THEN RECONNECT THE BATTERY.
With the DRBIII
t monitor active codes as you work through the following steps.
WARNING: MAINTAIN A SAFE DISTANCE FROM ALL AIRBAGS WHILE
PERFORMING THE FOLLOWING STEPS.
Wiggle the wiring harness and connectors of the related airbag circuit or component.
If codes are related to the Driver circuits, rotate the steering wheel from stop to stop.
You have just attempted to simulate the condition that initially set the trouble code
message.
Did the DTC become active?
All
Yes
→ Select appropriate symptom from Symptom List.
No
→ No problem found at this time. Erase all codes before returning
vehicle to customer.
45
AIRBAG
AIRBAG WARNING INDICATOR OPEN —
Continued
Symptom:
CALIBRATION MISMATCH
When Monitored and Set Condition:
CALIBRATION MISMATCH
When Monitored:
With ignition on, the ACM monitors the PCI Bus for the VIN message
containing the body style. Note: The VIN message should match the vehicle VIN plate.
Set Condition:
If the Body style stored in ACM does not exactly match the vehicle body
style indicated by the PCM for 2 consecutive VIN messages, then the fault shall be set.
POSSIBLE CAUSES
PCM, PCI COMMUNICATION FAILURE
PCM VEHICLE IDENTIFICATION NUMBERS INCORRECT OR MISSING
ACM CALIBRATION MISMATCH
STORED CODE OR INTERMITTENT CONDITION
ACTIVE CODE PRESENT
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
NOTE: Ensure the battery is fully charged.
NOTE: For the purpose of this test, the AECM and ORC modules will be
referred to as an ACM.
SELECT ACTIVE or STORED DTC:
All
ACM - ACTIVE DTC
ACM - STORED DTC
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
2
Turn the ignition on.
NOTE: Ensure the battery is fully charged.
Connect the DRB to the data link connector and select PASSIVE RESTRAINTS,
AIRBAG, SYSTEM TEST.
With the DRBIII
t, read the system test.
Does the DRB show PCM Active on the Bus:?
All
Yes
→ Go To 3
No
→ Refer to category COMMUNICATION CATEGORY and select the
related symptom.
Perform AIRBAG VERIFICATION TEST - VER 1.
46
AIRBAG
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст