Chrysler Voyager. Manual — part 182
TEST
ACTION
APPLICABILITY
2
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
Disconnect the Passenger Airbag connector(s).
NOTE: Check connectors - Clean and repair as necessary.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED AIRBAG FACE
DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL INTO THE AIR
IF ACCIDENTALLY DEPLOYED, AND COULD RESULT IN SERIOUS OR
FATAL INJURY.
Connect the appropriate Load Tool to the Passenger Airbag connector(s).
WARNING: TURN THE IGNITION ON, THEN RECONNECT THE BATTERY.
With the DRBIII
t, read the active Airbag Control Module DTC’s.
Does the DRBIII
t show PASSENGER SQUIB 2 CIRCUIT SHORT TO GROUND?
All
Yes
→ Go To 3
No
→ Replace the Passenger Airbag in accordance with the Service
Information.
Perform AIRBAG VERIFICATION TEST - VER 1.
3
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED AIRBAG FACE
DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL INTO THE AIR
IF ACCIDENTALLY DEPLOYED, AND COULD RESULT IN SERIOUS OR
FATAL INJURY.
Disconnect the Load Tool from the Passenger Airbag connector(s).
Disconnect the Airbag Control Module connector(s).
NOTE: Check connectors - Clean repair as necessary.
Connect the appropriate Load Tool Adaptor to the Airbag Control Module connec-
tor(s).
Measure the resistance of the Passenger Squib 2 Line 1 and Line 2 circuits between
the Passenger Airbag Module connector and ground.
Is the resistance below 10K ohms on either circuit?
All
Yes
→ Repair Passenger Squib 2 Line 1 or Line 2 circuit for a short to
ground.
Perform AIRBAG VERIFICATION TEST - VER 1.
No
→ Replace the Airbag Control Module in accordance with Service
Information. WARNING: IF THE AIRBAG CONTROL MODULE
IS DROPPED AT ANY TIME, IT MUST BE REPLACED.
Perform AIRBAG VERIFICATION TEST - VER 1.
155
AIRBAG
PASSENGER SQUIB 2 SHORT TO GROUND —
Continued
TEST
ACTION
APPLICABILITY
4
With the DRBIII
t, record and erase all DTC’s from all Airbag modules.
If equipped with Passenger Airbag On - Off switch, read the DTC’s in all switch
positions.
If any ACTIVE codes are present they must be resolved before diagnosing any stored
codes.
WARNING: TURN THE IGNITION OFF, DISCONNECT THE BATTERY AND
WAIT TWO MINUTES BEFORE PROCEEDING.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Look for chaffed, pierced, pinched, or partially broken wires and broken, bent, pushed
out, spread, corroded, or contaminated terminals.
The following additional checks may assist you in identifying a possible intermittent
problem.
Reconnect any disconnected components and harness connector.
WARNING: TURN THE IGNITION ON, THEN RECONNECT THE BATTERY.
With the DRBIII
t monitor active codes as you work through the following steps.
WARNING: MAINTAIN A SAFE DISTANCE FROM ALL AIRBAGS WHILE
PERFORMING THE FOLLOWING STEPS.
Wiggle the wiring harness and connectors of the related airbag circuit or component.
If codes are related to the Driver circuits, rotate the steering wheel from stop to stop.
You have just attempted to simulate the condition that initially set the trouble code
message.
Did the DTC become active?
All
Yes
→ Select appropriate symptom from Symptom List.
No
→ No problem found at this time. Erase all codes before returning
vehicle to customer.
156
AIRBAG
PASSENGER SQUIB 2 SHORT TO GROUND —
Continued
Symptom:
SEAT SQUIB CIRCUIT OPEN
When Monitored and Set Condition:
SEAT SQUIB CIRCUIT OPEN
When Monitored:
With the ignition on, the SIACM monitors the resistance of the Seat
Squib circuits.
Set Condition:
When the SIACM detects an open circuit or high resistance on the Seat
Squib circuits.
POSSIBLE CAUSES
SEAT AIRBAG CIRCUIT OPEN
SEAT SQUIB LINE 1 OR LINE 2 CIRCUIT OPEN
SIACM, SEAT SQUIB CIRCUIT OPEN
STORED CODE OR INTERMITTENT CONDITION
ACTIVE CODE PRESENT
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
NOTE: Ensure that the battery is fully charged.
NOTE: For the purpose of this test, the AECM and ORC modules will be
referred to as an ACM.
Select the appropriate module and DTC type combination:
All
LEFT SIACM - ACTIVE DTC
LEFT SIACM - STORED DTC
RIGHT SIACM - ACTIVE DTC
RIGHT SIACM - STORED DTC
NOTE: When reconnecting Airbag system components, the ignition must be
turned off and the battery must be disconnected.
157
AIRBAG
TEST
ACTION
APPLICABILITY
2
WARNING: TURN IGNITION OFF, DISCONNECT THE BATTERY AND WAIT
TWO MINUTES BEFORE PROCEEDING.
Disconnect the Seat Airbag connector.
NOTE: Check connectors - Clean and repair as necessary.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED SEAT BACK PAD-
DED SIDE DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL
INTO THE AIR IF ACCIDENTALLY DEPLOYED, AND COULD RESULT IN
SERIOUS OR FATAL INJURY.
Connect the appropriate Load Tool to the Seat Airbag connector.
WARNING: TURN IGNITION ON, THEN RECONNECT THE BATTERY.
With the DRBIII
t, read the SIACM active DTC’s.
Does the DRB show SEAT SQUIB CIRCUIT OPEN?
All
Yes
→ Go To 3
No
→ Replace Seat Airbag in accordance with the Service Information.
Perform AIRBAG VERIFICATION TEST - VER 1.
3
WARNING: TURN IGNITION OFF, DISCONNECT THE BATTERY AND WAIT
TWO MINUTES BEFORE PROCEEDING.
Disconnect the Load Tool from the Seat Airbag Connector.
NOTE: Check connectors - Clean and repair as necessary.
WARNING: DO NOT PLACE AN INTACT UNDEPLOYED SEAT BACK PAD-
DED SIDE DOWN ON A HARD SURFACE, THE AIRBAG WILL PROPEL
INTO THE AIR IF ACCIDENTALLY DEPLOYED, AND COULD RESULT IN
SERIOUS OR FATAL INJURY.
Disconnect the Side Impact Airbag Control Module Connector.
If the SIACM connector is equipped with shorting clips or bars connect the
appropriate Airbag Load Tool SIACM Adapter to the connector.
Measure the resistance of the Seat Squib Line 1 and Line 2 circuits between the Load
Tool SIACM adaptor and the Seat Airbag connector.
Is the resistance below 1.0 ohms on both circuits?
All
Yes
→ Replace the Side Impact Airbag Control Module in accordance
with the Service information. WARNING: IF THE SIDE IMPACT
AIRBAG CONTROL MODULE IS DROPPED AT ANY TIME, IT
MUST BE REPLACED.
Perform AIRBAG VERIFICATION TEST - VER 1.
No
→ Repair open or high resistance in the Seat Squib Line 1 or Line 2
circuits.
Perform AIRBAG VERIFICATION TEST - VER 1.
158
AIRBAG
SEAT SQUIB CIRCUIT OPEN —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст