Chrysler Voyager. Manual — part 324
TEST
ACTION
APPLICABILITY
3
Turn ignition off.
Disconnect the Driver Power Seat Recliner Position Sensor Connector.
Disconnect the Memory Seat Mirror Module C1 Connector.
Measure the resistance of the Recliner Position Signal circuit between the Recliner
sensor and the Memory Seat Mirror Module connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 4
No
→ Repair the Recliner Position Signal circuit for an open.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
4
Turn ignition off.
Disconnect the Memory Seat Mirror Module C1 connector.
Disconnect the Driver Power Seat Recliner Position Sensor connector.
Measure the resistance of the Recliner Position Signal circuit to ground.
Is the resistance below 1000 ohms?
All
Yes
→ Repair the Recliner Position Signal circuit a short to ground.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
No
→ Go To 5
5
Turn ignition off.
Ensure the Memory Seat Mirror Module is fully connected before proceeding.
Disconnect the Driver Power Seat Recliner Position Sensor Connector.
Connect a jumper wire between Seat Sensor 5 volt Supply and Recliner Position
Signal circuits.
Turn ignition on.
With the DRBIII
t select Body Memory Seat Sensors.
Read the Recliner Position Sensor voltage.
Is the voltage above 4.5 volts?
All
Yes
→ Replace the Seat Track Assembly.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
No
→ Go To 6
6
If there are no possible causes remaining, view repair.
All
Repair
Replace the Memory Seat Mirror Module.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
7
Turn ignition off.
Disconnect the Memory Seat Mirror Module C2 connector.
Measure the resistance of the Seat Sensor 5 volt supply circuit to body ground.
Is the resistance below 100.0 ohms?
All
Yes
→ Repair the Seat 5 Volt Supply circuit for a short to ground.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
No
→ Go To 8
723
MEMORY SEAT
RECLINER SENSOR OUT OF RANGE LOW —
Continued
TEST
ACTION
APPLICABILITY
8
Turn ignition off.
Disconnect the Memory Seat Mirror Module C2 connector.
Disconnect the Driver Power Seat Recliner Position Sensor connector.
Measure the resistance of the Seat Sensor 5 Volt Supply wire between the Recliner
Sensor connector and the C2 connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 9
No
→ Repair the Seat Sensor 5 Volt Supply circuit for an open.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
9
If there are no possible cause remaining, view repair.
All
Repair
Replace the Memory Mirror Module.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
724
MEMORY SEAT
RECLINER SENSOR OUT OF RANGE LOW —
Continued
Symptom:
RECLINER UP POSITION STUCK
When Monitored and Set Condition:
RECLINER UP POSITION STUCK
When Monitored:
Continuously when the PCI bus is active.
Set Condition:
If the seat switch is active for 30 seconds, this code will set and the
Memory Seat Mirror Module will ignore the input until the state has changed. Three
seconds after the stuck condition is removed, the seat will resume to normal operation.
Code will remain for 50 ignition cycles.
POSSIBLE CAUSES
STORED DIAGNOSTIC TROUBLE CODE
DRIVER POWER SEAT SWITCH
RECLINER UP SWITCH SENSE WIRE SHORT TO VOLTAGE
MEMORY SEAT MIRROR MODULE
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, erase the DTC from Memory Seat Mirror Module.
Operate the driver’s power seat and memory system.
Turn the ignition switch to the Off position then start the engine and let run for one
minute.
With the DRB check for the same DTC to reset in the MSMM.
Did the same DTC reset?
All
Yes
→ Go To 2
No
→ Using the wiring diagram/schematic as a guide, inspect the
wiring and connectors for an intermittent condition.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
2
Disconnect the Power Seat Switch connector.
Measure the voltage of the Recliner Up Switch Sense circuit.
Is there any voltage present?
All
Yes
→ Go To 3
No
→ Replace the Power Seat Switch.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
3
Disconnect the Power Seat Switch connector.
Disconnect the Memory Seat Mirror Module C1 connector.
Turn the ignition on.
Measure the voltage of the Recliner Up Switch Sense circuit to ground..
Is there any voltage present?
All
Yes
→ Repair the Recliner Up Switch Sense wire for a short to voltage.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
No
→ Go To 4
725
MEMORY SEAT
TEST
ACTION
APPLICABILITY
4
If there are no possible causes remaining, view
9Repair9.
All
Repair
Replace the Memory Seat Mirror Module.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
726
MEMORY SEAT
RECLINER UP POSITION STUCK —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст