Chrysler Voyager. Manual — part 358
TEST
ACTION
APPLICABILITY
4
Remove the Power Liftgate Motor trim panel.
Remove the Liftgate trim panel.
Disconnect the Power Liftgate Module C2 connector.
Disconnect the Right Pinch Sensor connector
Measure the resistance between ground and the Pinch Sensor Signal circuit.
Is the resistance below 100.0 ohms?
All
Yes
→ Go To 5
No
→ Replace the Right Pinch Sensor.
Perform BODY VERIFICATION TEST - VER 1.
5
Remove the Liftgate trim panel.
Disconnect the Right Pinch Sensor connector.
Disconnect the Left Pinch Sensor connector.
Measure the resistance between ground and the Right Pinch Sensor Signal circuit.
Is the resistance below 1000.0 ohms?
All
Yes
→ Repair the Right Pinch Sensor Signal wire for a short to ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 6
6
Remove the Power Liftgate Motor trim panel.
Remove the liftgate trim panel.
Disconnect the Power Liftgate Module C2 connector.
Disconnect the Left Pinch Sensor connector
Measure the resistance between ground and the Pinch Sensor Signal circuit.
Is the resistance below 100.0 ohms?
All
Yes
→ Go To 7
No
→ Replace the Left Pinch Sensor.
Perform BODY VERIFICATION TEST - VER 1.
7
If there are no possible causes remaining, view repair.
All
Repair
Repair the Pinch Sensor Signal wire for a short to ground.
Perform BODY VERIFICATION TEST - VER 1.
859
POWER DOORS - LIFTGATE
PINCH SENSOR SIGNAL CIRCUIT SHORT TO GROUND —
Continued
Symptom:
*POWER LIFTGATE INOPERATIVE
POSSIBLE CAUSES
DTC’S PRESENT
MODULE RESPONSE
INTERMITTENT PROBLEM
SYSTEM TESTS
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t check for response from the Body Computer and the Power
Liftgate Modules
Is there response from both modules?
All
Yes
→ Go To 2
No
→ Refer to symptom list for problems related to COMMUNICA-
TION.
2
With the DRBIII
t, read DTCs in POWER LIFTGATE and BODY COMPUTER.
Are any Power Liftgate related codes present?
All
Yes
→ Refer to symptom list for problems related to POWER LIFT-
GATE.
No
→ Go To 3
3
This test will determine what inhibited the Power Liftgate from operating properly.
With the DRBIII
t, select POWER LIFTGATE, MISCELLANEOUS, LAST INHIBIT
MONITOR.
Does the DRBIII
t display any INHIBIT REASONS?
All
Yes
→ Check for any binding conditions or other restrictions that may
prevent proper operation. Using the wiring diagram/schematic as
a guide, inspect the wiring and connectors.
No
→ Go To 4
4
Ensure Liftgate is fully closed before proceeding.
With the DRBIII
t select SYSTEM TEST.
Perform the Open, Close, Latch Cinch, Latch Release and Relay tests.
Did any test fail?
All
Yes
→ Using the wiring diagram/schematic as a guide, inspect the
wiring and connectors.
No
→ Test Complete.
860
POWER DOORS - LIFTGATE
Symptom:
AMBIENT TEMPERATURE SENSOR CIRCUIT OPEN
When Monitored and Set Condition:
AMBIENT TEMPERATURE SENSOR CIRCUIT OPEN
When Monitored:
Anytime the Power Sliding Door Module is awake.
Set Condition:
If the Power Sliding Door Modules internal thermistor becomes open, this
code will set.
POSSIBLE CAUSES
DTC PRESENT
POWER SLIDING DOOR MODULE
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, record and erase DTC’s.
Turn the ignition off, wait 10 seconds, then turn the ignition on.
Operate the power sliding door several times from stop to stop if possible.
With the DRBIII
t, read ACTIVE DTCs.
Does the DRBIII
t display AMBIENT TEMPERATURE SENSOR CIRCUIT HIGH?
All
Yes
→ Replace the Power Sliding Door Module.
Perform BODY VERIFICATION TEST - VER 1.
No
→ No problem found at this time.
Perform BODY VERIFICATION TEST - VER 1.
861
POWER DOORS - SLIDING
Symptom:
AMBIENT TEMPERATURE SENSOR CIRCUIT SHORT TO GROUND
When Monitored and Set Condition:
AMBIENT TEMPERATURE SENSOR CIRCUIT SHORT TO GROUND
When Monitored:
Anytime the Power Sliding Door Module is awake.
Set Condition:
If the Power Sliding Door Modules internal thermistor is shorted, this
code will set.
POSSIBLE CAUSES
DTC PRESENT
POWER SLIDING DOOR MODULE
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, record and erase DTC’s.
Turn the ignition off, wait 10 seconds, then turn the ignition on.
Operate the power sliding door several times from stop to stop if possible.
With the DRBIII
t, read ACTIVE DTCs.
Does the DRBIII
t display AMBIENT TEMPERATURE SENSOR CIRCUIT LOW?
All
Yes
→ Replace the Power Sliding Door Module.
Perform BODY VERIFICATION TEST - VER 1.
No
→ No problem found at this time.
Perform BODY VERIFICATION TEST - VER 1.
862
POWER DOORS - SLIDING
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст