Chrysler Voyager. Manual — part 373
Symptom:
LOSS OF BCM MESSAGES
When Monitored and Set Condition:
LOSS OF BCM MESSAGES
When Monitored:
Whenever the ignition is on.
Set Condition:
If the PSD Module losses communication with the BCM for over 5 seconds,
this code will set.
POSSIBLE CAUSES
ATTEMPT TO COMMUNICATE WITH THE BODY CONTROL MODULE
POWER SLIDING DOOR MODULE - LOSS OF BCM MESSAGES
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, enter Body then Body Computer.
Was the DRBIII
t able to I/D or communicate with the BCM?
All
Yes
→ Go To 2
No
→ Refer to the Communication category for the related symptom(s).
2
With the DRBIII
t, erase DTC’s.
Cycle the ignition switch from off to on and wait approximately 1 minute.
With the DRBIII
t, read DTC’s.
Did this DTC reset?
All
Yes
→ Replace the Power Sliding Door Module.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
919
POWER DOORS - SLIDING
Symptom:
LOSS OF EATX MESSAGES
When Monitored and Set Condition:
LOSS OF EATX MESSAGES
When Monitored:
Whenever the ignition is on.
Set Condition:
If the PSD Module does not receive a PRNDL message for over 5 seconds,
this code will set.
POSSIBLE CAUSES
ATTEMPT TO COMMUNICATE WITH THE TRANSMISSION CONTROL MODULE
POWER SLIDING DOOR MODULE - LOSS OF EATX MESSAGES
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, select Transmission.
Was the DRBIII
t able to I/D or communicate with the Transmission?
All
Yes
→ Go To 2
No
→ Refer to the Communication category for the related symptom(s).
2
With the DRBIII
t, erase DTC’s.
Cycle the ignition switch from off to on and wait approximately 1 minute.
With the DRBIII
t, read DTC’s.
Did this DTC reset?
All
Yes
→ Replace the Power Sliding Door Module.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
920
POWER DOORS - SLIDING
Symptom:
LOSS OF FCM MESSAGES
When Monitored and Set Condition:
LOSS OF FCM MESSAGES
When Monitored:
Whenever the ignition is in the RUN position and the PRNDL is not in
PARK position.
Set Condition:
If the PSD Module does not receive a temperature message from the Front
Control Module for over 5 seconds, this code will set.
POSSIBLE CAUSES
ATTEMPT TO COMMUNICATE WITH THE FRONT CONTROL MODULE
POWER SLIDING DOOR MODULE - LOSS OF FCM MESSAGES
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, enter Body then Front Control Module.
Was the DRBIII
t able to I/D or communicate with the FCM?
All
Yes
→ Go To 2
No
→ Refer to the Communication category for the related symptom(S).
2
With the DRBIII
t, erase DTC’s.
Cycle the ignition switch from off to on and wait approximately 1 minute.
With the DRBIII
t, read DTC’s.
Did this DTC reset?
All
Yes
→ Replace the Power Sliding Door Module.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
921
POWER DOORS - SLIDING
Symptom:
LOSS OF SBEC MESSAGES
When Monitored and Set Condition:
LOSS OF SBEC MESSAGES
When Monitored:
Whenever the ignition is in RUN position and the PRNDL is not in
PARK position.
Set Condition:
If the PSD Module does not receive a speed message from the Powertrain
Control Module for over 5 seconds, this code will set.
POSSIBLE CAUSES
ATTEMPT TO COMMUNICATE WITH THE POWERTRAIN CONTROL MODULE
POWER SLIDING DOOR MODULE - LOSS OF SBEC MESSAGES
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, select Engine.
Was the DRBIII
t able to I/D or communicate with the Transmission?
All
Yes
→ Go To 2
No
→ Refer to the Communication category for the related symptom(s).
2
With the DRBIII
t, erase DTC’s.
Cycle the ignition switch from OFF to RUN and wait approximately 1 minute.
With the DRBIII
t, read DTC’s.
Did this DTC reset?
All
Yes
→ Replace the Power Sliding Door Module.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
922
POWER DOORS - SLIDING
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст