Fiat Bravo (2015 year). Instruction — part 4

MANUAL CLIMATE CONTROL

SYSTEM

(for versions/markets, where provided)

CONTROLS

fig. 31

F0Q0610

A air temperature adjustment knob (hot/cold air

❒ turn knob E to

;

mixing)

❒ turn off internal air recirculation (LED on button

B heated rear window on/off button

off ).

C fan activation knob

After demisting/defrosting, operate the controls to

D climate control system compressor on/off button

maintain optimum visibility conditions.

E internal air recirculation on/off button

Window demisting

F air distribution knob.

In the event of considerable external moisture

PASSENGER COMPARTMENT HEATING

and/or rain and/or large differences in temperature

inside and outside the passenger compartment,

Proceed as follows:

perform the following preventive window demisting

❒ turn knob A to the red section;

procedure:

❒ turn knob C to the required speed;

❒ press the button

❒ turn knob F to:

❒ turn off internal air recirculation (LED on button

to warm the feet and demist the windscreen at

off );

the same time

❒ turn knob A to the red section;

to warm the feet and keep the face cool (bi-level

❒ turn knob C to the second speed level;

function)

❒ turn knob F to or to if there is no sign of

to warm the feet of those in the front and rear

the windows steaming up.

seats

The climate control system is very useful for

❒ to turn off internal air recirculation (LED on

demisting the windows more quickly: just carry out

button

off ).

the above procedure and activate the system by

pressing button

FAST FRONT WINDOW DEMISTING/

DEFROSTING

Proceed as follows:

❒ press the button

❒ turn knob A fully to the right;

❒ turn knob C to

;

HEATED REAR WINDOW AND DOOR

It is advisable to switch the internal air recirculation

MIRRORS DEMISTING/DEFROSTING

on while standing in queues or in tunnels to prevent

the introduction of polluted air. However, it is better

Press button

to activate this function: when this

not to use the function for long periods, particularly

function is activated, the button LED

lights up.

if there are many people on board, to prevent the

This function is timed and will deactivate

windows from misting.

automatically after 20 minutes. Press the button

again to switch the function off in advance.

IMPORTANT Internal air recirculation makes it

possible to reach the required heating or cooling

IMPORTANT Do not apply stickers on the inside of

conditions more quickly depending on the mode

the rear window over the heating filaments to avoid

selected. It is not advisable to switch the internal air

damage.

recirculation on when it is rainy/cold or the windows

might steam up, especially if the climate control

FAN SPEED ADJUSTMENT

system is not turned on.

To ventilate the passenger compartment properly,

CLIMATE CONTROL SYSTEM (cooling)

proceed as follows:

Proceed as follows:

❒ fully open the central and side air diffusers;

❒ turn knob A to the blue section;

❒ turn knob C to the required speed;

❒ turn knob F to

;

❒ turn knob E to

;

❒ press and

buttons (button LEDs on).

❒ turn off internal air recirculation (LED on button

off ).

Cooling adjustment

INTERNAL AIR RECIRCULATION

Proceed as follows:

ACTIVATION

❒ deactivate the

button (LED on button off );

Press button

: when the function is on, the

❒ turn knob A rightwards to increase the

button LED lights up.

temperature;

❒ turn knob C leftwards to reduce the fan speed.

ADDITIONAL HEATER

SYSTEM MAINTENANCE

(for versions/markets, where provided)

In winter, the climate control system must be turned

This device warms up the passenger compartment

on at least once a month for about 10 minutes.

more quickly when it is very cold and the engine

Before summer, have the system checked at a Fiat

coolant temperature is low.

Dealership.

The additional heater comes on automatically when

the engine is started, if knob A is turned to the

last red sector and the fan (knob C) is at least at the

first speed level.

The heater switches off automatically when the

required comfort conditions are achieved.

IMPORTANT The heater will not turn on if the

battery voltage is too low.

AUTOMATIC DUAL ZONE CLIMATE

CONTROL SYSTEM

(for versions/markets, where provided)

fig. 32

F0Q0611

DESCRIPTION

SWITCHING ON THE CLIMATE CONTROL

SYSTEM

The car is equipped with a dual zone climate control

system which allows you to adjust the air

The system can be activated by pressing any of the

temperature on the driver's and the passenger's side

buttons; it is, however, advisable to set the desired

separately.

temperatures on the

The system has an AQS function (Air Quality

display, then press the AUTO button.

System)(for versions/markets, where provided)

The climate control system allows you to customise

which automatically activates internal air

the temperatures requested (driver side and

recirculation when the outside air is polluted (e.g. in

passenger side) with a maximum difference of 7°C.

traffic queues and tunnels).

The climate control system compressor works

only with the engine running and an outside

CONTROLS

temperature of above 4°C.

A AUTO function activation button (automatic

operation) and driver side temperature adjustment

AUTOMATIC OPERATION OF THE

knob

CLIMATE CONTROL SYSTEM (AUTO

B air distribution selection button

function)

C climate control system information display

Press the AUTO button; the system will

D fan speed increase/decrease

automatically adjust:

E MONO function activation button (set

❒ the amount of air introduced into the passenger

temperature alignment) and passenger side

compartment;

temperature adjustment knob

❒ the distribution of the air in the passenger

F climate control system on/off button

compartment;

G heated rear window on/off button

cancelling all previous instruction adjustments.

H MAX-DEF function activation button (rapid

During climate control system automatic operation,

defrosting/demisting of front windows)

the words FULL AUTO appear on the display.

I internal air temperature sensor

L internal air recirculation and AQS function on/off

button

(for versions/markets, where provided)

M climate control system compressor on/off button

During automatic operation it is still possible to

RAPID FRONT WINDOW

adjust the temperatures set and carry out the

DEMISTING/DEFROSTING

following operations instructionly:

(MAX-DEF function)

❒ fan speed adjustment;

Press button to automatically activate the timed

❒ air distribution selection;

operation of all the functions required to rapidly

demist/defrost the windscreen and front side

❒ internal air recirculation and AQS function

windows.

activation/deactivation;

The functions are:

❒ climate control system compressor activation.

❒ climate control system compressor activation

(with an outside temperature of above 4°C);

WARNING

❒ switching off, if previously on, of the internal air

It is advisable not to use the internal air

recirculation (LED on button

off );

recirculation function when the outside

❒ activation of heated rear window (LED on button

temperature is low, because the windows could

on) and door mirror heater coils;

mist rapidly.

❒ setting maximum air temperature;

❒ activation of air flow.

FAN SPEED ADJUSTMENT

HEATED REAR WINDOW AND DOOR

Press button to increase/decrease the fan speed.

MIRRORS DEMISTING/DEFROSTING

The 12 possible speeds are indicated by bars lighting

up on the display:

Press button

to activate: when this function is

activated, the button LED switches on.

❒ maximum fan speed = all bars lit

This function is timed and will deactivate

❒ minimum fan speed = one bar lit.

automatically after 20 minutes. Press the button

The fan can be disabled (no bars lit) only if the

again to switch the function off in advance.

climate control system compressor has been

switched off by pressing button

IMPORTANT Do not apply stickers on the inside of

the rear window over the heating filaments to avoid

To restore automatic fan speed control after a

damage.

instruction adjustment, press the AUTO button.

IMPORTANT Press

to introduce air from the

IMPORTANT Internal air recirculation makes it

outside (in this case the LED on the button should

possible to reach the required heating or cooling

be off ).

conditions more quickly depending on the mode

selected. It is not advisable to switch the internal air

ACTIVATION OF INTERNAL AIR

recirculation on when it is rainy/cold to prevent

RECIRCULATION AND ENABLEMENT OF

the windows from misting, especially if the climate

AQS FUNCTION (Air Quality System)

control system has not been activated. It is advisable

to switch the internal air recirculation on whilst

(for versions/markets, where provided)

queuing or in tunnels to prevent the introduction of

Press button

. Internal air recirculation is carried

polluted air. Do not use the function for a long

out according to three possible operating modes:

time, particularly if there are several passengers on

board, to prevent the windows from misting.

❒ automatic control, signalled by the AQS sign

on the display and the LED on button

being

AQS (Air Quality System) function activation

off;

(for versions/markets, where provided)

❒ forced deactivation (internal air recirculation

always off with introduction of outside air),

The AQS function (AQS sign on the display)

indicated by the LED on button

being off;

automatically activates internal air recirculation when

the outside air is polluted (e.g. in traffic queues and

❒ forced activation (internal air recirculation always

tunnels).

on), signalled by the LED on button

being lit.

When OFF button is pressed, the climate control

IMPORTANT With the AQS function active, after

system automatically activates internal air

approx. 15 consecutive minutes of the internal

recirculation (the LED on button T should be on). It

air recirculation system functioning, the climate

is still possible to activate outside air recirculation

control system enables the intake of outside air for

(LED on the button off ) and vice versa, by pressing

approximately 1 minute to freshen the air in the

button T.

passenger compartment. This takes place regardless

of the pollution level of the outside air.

With the OFF button pressed (LED on the button is

lit up), it is not possible to enable the AQS (Air

Quality System) function.

SET TEMPERATURE ALIGNMENT

The deactivation of the climate control system

(MONO function)

compressor is memorised even after the engine has

stopped. To reactivate the climate control system

Press the MONO button to align the temperature

compressor, press the or AUTO button again:

between the driver side and passenger side.

if you press AUTO, the other instruction settings will be

Then turn the AUTO or MONO knob to

cancelled.

increase/decrease the temperature between the two

areas by the same amount.

IMPORTANT In order to preserve the battery

charge, the electronic climate control management

Press MONO again to deactivate the function.

permits a higher ventilation speed than minimum

only if the engine is running at a speed greater than

CLIMATE CONTROL SYSTEM

750 rpm. When the speed drops below this

COMPRESSOR ACTIVATION/

threshold - possible when setting off, for example -

DEACTIVATION

the ventilation speed is automatically reduced to

Press the button to switch on the climate control

minimum.

system compressor.

AIR DISTRIBUTION SELECTION

Compressor engagement

Press one or more of these buttons

❒ button LED on;

instructionly select one of the seven possible air

distribution settings for the passenger compartment:

❒ symbol appears on display.

Air flow to the windscreen and front side

Compressor deactivation

window diffusers to demist/defrost them.

❒ button LED off;

Air flow to the front and rear footwell diffusers.

This air distribution allows the passenger

❒ symbol on display disappears;

compartment to be warmed up quickly.

❒ internal air recirculation excluded;

Air flow distribution between front and

❒ AQS function disabled

rear diffusers, centre/side dashboard

(for versions/markets, where provided).

diffusers, rear diffuser and windscreen and

front side window demisting/defrosting

With the climate control system compressor

diffusers.

switched off, air cannot be introduced into the

passenger compartment that has a lower

Air flow distribution to centre/side dashboard

temperature than the outside air; in this case the

diffusers (passenger's body).

symbol in the display will flash.

Air flow distribution between footwell

ADDITIONAL HEATER

diffusers and windscreen and front side

(for versions/markets, where provided)

window defrosting/demisting diffusers. This

This device warms up the passenger compartment

distribution setting allows the passenger

more quickly when it is very cold and the engine

compartment to be warmed effectively and

coolant temperature is low.

prevents the windows from misting.

Air flow distribution between footwell

In these conditions, the device comes on

automatically when the engine is started and the fan

diffusers (hotter air) and centre/side

is on.

dashboard diffusers and rear diffuser (cooler

air).

The heater switches off automatically when the

Air flow distribution between centre/side

required comfort conditions are achieved.

dashboard diffusers, rear diffuser and

IMPORTANT The heater will not turn on if the

windscreen and front side window

battery voltage is too low.

demisting/defrosting diffusers. This

distribution setting ventilates the passenger

SWITCHING OFF THE CLIMATE CONTROL

compartment well and prevents the windows

SYSTEM

from misting up.

Press the OFF button.

IMPORTANT For the climate control system to

function, at least one of the buttons

must

The following information is shown on the display:

be operated. The system does not allow the

❒ OFF;

deactivation of all the buttons

❒ outside temperature indication;

IMPORTANT Push the OFF button to turn the

❒ internal air recirculation on indication (LED on

climate control system back on: in this way, all

button

lit).

operating conditions memorised before switching off

are restored.

To restore automatic control of the air distribution

after a instruction selection, press the AUTO button.

EXTERIOR LIGHTS

The warning light

switches on in the instrument

panel.

The left lever fig. 33 includes the controls for the

exterior lights.

MAIN BEAM HEADLIGHTS

The exterior lights can only be switched on when

With the ring nut at

position, push the stalk

the ignition key is at MAR-ON.

forward towards the dashboard (stable position).

The warning light

switches on in the instrument

LIGHTS OFF

panel.

Ring nut turned to position

To turn the main beam headlights off, pull the stalk

towards the steering wheel (dipped headlights will

SIDE LIGHTS

turn on).

Turn the ring nut to position

PARKING LIGHTS

The warning light

switches on in the instrument

panel.

These lights can be turned on only with the ignition

key at STOP or extracted by turning the ring nut

DIPPED HEADLIGHTS

on the left stalk first to position and then to

position

Turn the ring nut to position

The warning light

switches on in the instrument

panel. Operate the direction indicator stalk to select

the side (right or left).

FLASHING

Pull the stalk towards the steering wheel (unstable

position) regardless of the position of the ring nut.

The warning light

switches on in the instrument

panel.

fig. 33

F0Q0649

DIRECTION INDICATORS

“Cornering lights”

Place the stalk in the (stable) position fig. 34:

When the dipped headlights are on and the speed is

below 40 km/h, if the steering wheel rotation angle is

❒ up (position 1): activates the right direction

large or the direction indicators are on, a light

indicator

(incorporated in the fog light) will come on on the

❒ down (position 2): activates the left direction

relevant side to improve visibility at nighttime.

indicator

Warning light or will flash in the instrument

"FOLLOW ME HOME" DEVICE

panel.

This allows the space in front of the car to be lit up

Direction indicators are switched off automatically

for a certain period of time.

when the steering wheel is straightened.

Activation

Lane change function

With the ignition key turned to STOP or removed,

If you wish to signal a lane change, put the left stalk

pull the stalk fig. 35 towards the steering wheel

in the unstable position for less than half a second.

within 2 minutes from when the engine is turned off.

The direction indicator on the side selected will flash

At each single movement of the stalk, the lights

five times and then switch off automatically.

will remain on for an extra 30 seconds up to a

maximum of 210 seconds; then the lights are

switched off automatically.

Each action of the stalk corresponds with the lighting

of the

warning light in the instrument panel

(along with a message shown on the display) (see

"Warning lights and messages" chapter).

Deactivation

Keep the stalk pulled towards the steering wheel for

more than 2 seconds.

fig. 34

F0Q0650

AUTOMATIC HEADLIGHT SENSOR

Deactivation

(dusk sensor)

The dipped headlights will switch off followed after

(for versions/markets, where provided)

approximately 10 seconds by the side lights, when

It detects variations in brightness outside the vehicle

the sensor is deactivated.

depending on the light sensitivity setting: the greater

The sensor is not capable of detecting the presence

the sensitivity, the less outside light needed to

of fog therefore, in these circumstances, the lights

activate the exterior lights being turned on.

have to be turned on instructionly.

The sensitivity of the dusk sensor may be adjusted by

means of the "Setup menu" on the instrument panel.

Activation

Turn the ring nut to position

fig. 36: this turns the

side lights and the dipped headlights on

simultaneously and automatically depending on the

exterior brightness conditions.

The headlights can only be flashed with the sensor

on.

fig. 35

F0Q0651

fig. 36

F0Q0652

WINDOW CLEANING

IMPORTANT With the windscreen wipers in use, if

reverse gear is engaged, the rear window wiper is

automatically activated.

WINDSCREEN WASHER/WIPER

They can be operated only with the ignition key

turned to MAR-ON.

The right stalk can be moved to five different

positions fig. 37:

A windscreen wiper off.

B intermittent operation.

With the stalk in position B, turn ring nut F to select

one of four different speeds for the intermittent

operation mode:

= intermittent low speed

= slow intermittent operation.

= medium intermittent operation.

= fast intermittent operation.

C continuous slow operation;

D continuous fast operation;

E temporary fast operation (unstable position).

Temporary fast operation position E is limited to the

time that the stalk is instructionly held in this position.

The stalk returns to position A when it is released,

automatically stopping the windscreen wipers.

fig. 37

F0Q0645

Была ли эта страница вам полезна?

Да!Нет

1 посетитель считают эту страницу полезной.

Fiat Bravo (2015 year). Instruction — part 4

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.