Dodge Durango (2019 year). Instruction — part 32

Setting Name

Selectable Options

Balance/Fade

Up Arrow

Button

Down Ar-

row Button

Left Arrow

Button

Right Ar-

row Button

Center “C”

Button

NOTE:
When in this display you may adjust the “Balance/Fade” of the audio by using the “Arrow” button on the touch-
screen to adjust the sound level from the front and rear or right and left side speakers. Press the “Center ‘C’ Button”
on the touchscreen to reset the balance and fade to the factory setting.

Speed Adjusted Volume

Off

1

2

3

Surround Sound — If Equipped

On

Off

Loudness — If Equipped

Yes

No

NOTE:
This feature improves sound quality at lower volumes when enabled.

AUX Volume Offset — If Equipped

On

Off

NOTE:
This feature provides the ability to tune the audio level for portable devices connected through the AUX input.

10

MULTIMEDIA

509

Phone/Bluetooth
After pressing the “Phone/Bluetooth” button on the touchscreen, the following settings will be available:

Setting Name

Selectable Options

Paired Phones

List of Paired Phones

NOTE:
The “Paired Phones” feature shows which phones are paired to the Phone/Bluetooth system. For further information,
refer to the Uconnect Owner’s Instruction Supplement.

SiriusXM Setup — If Equipped
After pressing the “SiriusXM Setup” button on the touchscreen, the following settings will be available:

Setting Name

Selectable Options

Channel Skip

List of Channels

NOTE:
SiriusXM can be programmed to designate a group of channels that are the most desirable to listen to or to exclude
undesirable channels while scanning. This feature allows you to select the channels you would like to skip.

510

MULTIMEDIA

Setting Name

Selectable Options

Subscription Info

Sirius ID

NOTE:
New vehicle purchasers or lessees will receive a free limited time subscription to SiriusXM Satellite Radio with your
radio. Following the expiration of the free services, it will be necessary to access the information on the Subscription
Information screen to re-subscribe.

1. Press the “Subscription Info” button on the touchscreen to access the Subscription Information screen.

2. Write down the Sirius ID numbers for your receiver. To reactivate your service, either call the number listed on the

screen or visit the provider online.

Reset
After pressing the “Reset” button on the touchscreen, the following settings will be available:

Setting Name

Selectable Options

Restore Settings to Default

OK

Cancel

X

NOTE:
When this feature is selected, it will reset all settings to their default settings. To restore the settings to their default
setting, press the “Restore Settings” button on the touchscreen. A pop-up will appear asking

⬙Are you sure you want

to reset your settings to default?”

Restore App Drawer to

Default Order

OK

Cancel

Restore Apps

OK

Cancel

10

MULTIMEDIA

511

Setting Name

Selectable Options

Clear Personal Data

OK

Cancel

X

NOTE:
When this feature is selected, it will remove all personal data including Bluetooth devices and presets. To remove per-
sonal information, press the “Clear Personal Data” button and a pop-up will appear asking

⬙Are you sure you want

to clear all personal data?”

Modem Reset

OK

Cancel

System Information
After pressing the “System Information” button on the touchscreen, the following settings will be available:

Setting Name

Selectable Options

Software License

System Software Information Screen

NOTE:
When the “System Information” feature is selected, a “System Software Information” screen will appear, displaying
the system software version.

512

MULTIMEDIA

Customer Programmable Features — Uconnect
4C/4C NAV Settings

Press the “Apps

” button, then press the “Settings”

button on the touchscreen to display the menu setting
screen. In this mode the Uconnect system allows you to
access programmable features that may be equipped
such as Language, Display, Units, Voice, Clock, Safety &
Driving Assistance, Mirrors & Wipers, Lights, Doors &
Locks, Auto-On Comfort, Engine Off Options, Suspen-
sion, Audio, Phone/Bluetooth, SiriusXM Setup, Acces-
sibility, Reset, and System Information.

NOTE:

Depending on the vehicles options, feature settings

may vary.

When making a selection, press the button on the touch-
screen to enter the desired mode. Once in the desired
mode, press and release the preferred setting “option” until
a check-mark appears next to the setting, showing that
setting has been selected. Once the setting is complete,
either press the “Back” Arrow button on the touchscreen to
return to the previous menu, or press the “X” button on the
touchscreen to close out of the settings screen. Pressing the
“Up” or “Down” Arrow button on the right side of the
screen will allow you to toggle up or down through the
available settings.

Language

After pressing the “Language” button on the touchscreen, the following settings will be available:

Setting Name

Selectable Options

Language

English

Espanol

Francais

When the “Set Language” feature is selected, you may select one of multiple languages (English / Français / Espa-
ñol) for all display nomenclature, including the trip functions and the navigation system (if equipped). Press the “Set
Language” button on the touchscreen, then press the desired language button on the touchscreen until a check-mark
appears next to the language, showing that setting has been selected.

10

MULTIMEDIA

513

Display
After pressing the “Display” button on the touchscreen, the following settings will be available:

Setting Name

Selectable Options

Display Mode

Instruction

Auto

Display Brightness With Headlights

ON

+

-

NOTE:
To make changes to the

⬙Display Brightness with Headlights ON⬙ setting, the headlights must be on and the interior

dimmer switch must not be in the

⬙party⬙ or ⬙parade⬙ positions.

Display Brightness With Headlights

OFF

+

-

NOTE:
To make changes to the

⬙Display Brightness with Headlights OFF⬙ setting, the headlights must be off and the interior

dimmer switch must not be in the

⬙party⬙ or ⬙parade⬙ positions.

Set Theme

On

Off

NOTE:
When the “Set Theme” feature is selected, you may select the theme for the display screen. To make your selection,
press the

⬙Set Theme⬙ button on the touchscreen, then select the desired theme option button until a check-mark ap-

pears showing that the setting has been selected.

Touchscreen Beep

On

Off

514

MULTIMEDIA

Setting Name

Selectable Options

Control Screen Time-Out — If

Equipped

On

Off

NOTE:
When the “Control Screen Time-Out” feature is selected, the Controls Screen will stay open for five seconds before
the screen times out. With the feature deselected, the screen will stay open until it is instructionly closed.

Navigation Turn-By-Turn In Cluster

— If Equipped

On

Off

NOTE:
When the “Navigation Turn-By-Turn In Cluster” feature is selected, the turn-by-turn directions will appear in the in-
strument cluster display as the vehicle approaches a designated turn within a programmed route.

Phone Pop-ups Displayed in Cluster

On

Off

Units
After pressing the “Units” button on the touchscreen, you may select each unit of measure independently displayed in the
instrument cluster display, and navigation system (if equipped). The following selectable units of measure are listed below:

Setting Name

Selectable Options

Units

US

Metric

Custom

NOTE:
The “Custom” option allows you to set the “Speed” (MPH, or km/h), “Distance” (mi, or km), “Fuel Consumption”
[MPG (US), MPG (UK), L/100 km, or km/L], “Pressure” (psi, kPa, or bar), and “Temperature” (°C, or °F) units of
measure independently.

10

MULTIMEDIA

515

Voice
After pressing the “Voice” button on the touchscreen, the following settings will be available:

Setting Name

Selectable Options

Voice Response Length

Brief

Detailed

Show Command List

Always

With Help

Never

Clock
After pressing the “Clock” button on the touchscreen, the following settings will be available:

Setting Name

Selectable Options

Sync Time With GPS

On

Off

Set Time Hours

+

-

NOTE:
The “Set Time Hours” feature allows you to adjust the hours. The “Sync time with GPS” button on the touchscreen
must be unchecked.

Set Time Minutes

+

-

NOTE:
The “Set Time Minutes” feature allows you to adjust the minutes. The “Sync time with GPS” button on the touch-
screen must be unchecked.

Time Format

12hrs

24hrs

AM

PM

Show Time in Status Bar — If Equipped

On

Off

516

MULTIMEDIA

Safety & Driving Assistance
After pressing the “Safety/Assistance” button on the touchscreen, the following settings will be available:

Setting Name

Selectable Options

ParkView Backup Camera

Delay

On

Off

NOTE:
The “ParkView Backup Camera Delay” setting determines whether or not the screen will display the rear view image
with dynamic grid lines for up to ten seconds after the vehicle is shifted out of REVERSE. This delay will be canceled
if the vehicle’s speed exceeds 8 mph (13 km/h), the transmission is shifted into PARK, or the ignition is switched to
the OFF position.

Active ParkView Backup

Camera Guidelines

On

Off

NOTE:
The “Active ParkView Backup Camera Guidelines” feature overlays the Rear Backup Camera image with active, or
dynamic, grid lines to help illustrate the width of the vehicle and its project back up path, based on the steering
wheel position when the option is checked. A dashed center line overlay indicates the center of the vehicle to assist
with parking or aligning to a hitch/receiver.

10

MULTIMEDIA

517

Setting Name

Selectable Options

Forward Collision Warn-

ing — If Equipped

Off

Warning Only

Warning & Braking

NOTE:
Changing the FCW status to “Off” prevents the system from warning you of a possible collision with the vehicle in
front of you.
The FCW system state is kept in memory from one ignition cycle to the next. If the system is turned OFF, it will re-
main off when the vehicle is restarted.
Forward Collision Warning includes Advanced Brake Assist (ABA). The ABA applies additional brake pressure when
the driver requests insufficient brake pressure to avoid a potential frontal collision. When the “Warning Only” option
is selected a chime sounds alerting you of a possible collision with the vehicle in front of you and more brake pres-
sure is needed. When the “Warning & Braking” option is selected, it applies the brakes to slow your vehicle in case of
a potential forward collision and sound an audible chime to alert you.

Forward Collision Warn-

ing Sensitivity — If

Equipped

Near

Med

Far

NOTE:
The “Forward Collision Warning Sensitivity” setting determines at what relative distance the vehicle directly in front
of you needs to be at, before the system warns you of a possible collision with the vehicle directly in front of you,
based on the option is selected. “Far” gives you the most amount of reaction time, whereas “Near” gives you the
least amount of reaction time, based on the distance between the two vehicles. The default setting is “Med.”

ParkSense — If Equipped

Sound Only

Sound & Display

518

MULTIMEDIA

Setting Name

Selectable Options

NOTE:
The “ParkSense” system setting scans for objects in front or behind the vehicle. Front Parksense scans for objects
when the transmission gear selector is in DRIVE, and Rear Parksense scans for objects when the transmission gear
selector is in REVERSE and the vehicle speed is less than 7 mph (11 km/h), when enabled. It provides an alert (au-
dible and/or visual) to indicate the proximity to other objects. The system can be enabled with “Sound Only,” or
“Sound & Display.”

Rear ParkSense Volume

Low

Medium

High

Front ParkSense Volume

Low

Medium

High

Rear ParkSense Braking

Assist — If Equipped

On

Off

NOTE:
When the “Rear ParkSense Braking Assist” feature is selected, the park assist system detects objects located behind
the vehicle and utilize autonomous braking to stop the vehicle.

LaneSense Warning — If

Equipped

Early

Medium

Late

NOTE:
The “LaneSense Warning” setting determines at what distance the LaneSense system warns you, through steering
wheel feedback, of a possible lane departure.

LaneSense Strength — If

Equipped

Low

Medium

High

10

MULTIMEDIA

519

Setting Name

Selectable Options

Blind Spot Alert — If

Equipped

Off

Lights

Lights & Chime

NOTE:
When the “Blind Spot Alert” feature is selected, the Blind Spot Alert system is activated and shows a visual alert in
the outside mirrors, and may also play an audible alert when the turn signal is on. When “Off” is selected, the Blind
Spot Alert system is deactivated.
If your vehicle has experienced any damage in the area where the sensor is located, even if the fascia is not damaged,
the sensor may have become misaligned. Take your vehicle to an authorized dealer to verify sensor alignment. A sen-
sor that is misaligned results in the Blind Spot Alert System not operating to specification.

Electric Power Steering
Default — If Equipped

Normal

Sport

Comfort

NOTE:
When “Electric Power Steering Default” is selected, it allows you to change the default setting of your vehicle to ei-
ther normal, sport, or comfort.

Hill Start Assist — If

Equipped

On

Off

520

MULTIMEDIA

Mirrors & Wipers
After pressing the “Mirrors & Wipers” button on the touchscreen, the following settings will be available:

Setting Name

Selectable Options

Rain Sensing Auto Wipers

On

Off

Tilt Side Mirrors in Reverse

On

Off

Headlights with Wipers

On

Off

Lights
After pressing the “Lights” button on the touchscreen, the following settings will be available.

Setting Name

Selectable Options

Headlight Off Delay

0 sec

30 sec

60 sec

90 sec

NOTE:
When the “Headlight Off Delay” feature is selected, it allows the adjustment of the amount of time the headlights
remain on after the engine is shut off.

Headlights With Wipers — If

Equipped

On

Off

10

MULTIMEDIA

521

Setting Name

Selectable Options

Headlight Illuminated On Approach

0 sec

30 sec

60 sec

90 sec

NOTE:
When the “Headlight Illumination On Approach” feature is selected, it allows the adjustment of the amount of time
the headlights remain on after the doors are unlocked with the key fob.

Auto Dim High Beams— If

Equipped

On

Off

NOTE:
When the “Auto Dim High Beams” feature is selected, the high beam headlights activates/deactivates automatically
under certain conditions.

Daytime Running Lights — If

Equipped

On

Off

Flash Lights With Lock

On

Off

522

MULTIMEDIA

Doors & Locks
After pressing the “Doors & Locks” button on the touchscreen, the following settings will be available:

Setting Name

Selectable Options

Auto Door Locks

On

Off

NOTE:
When the “Auto Door Locks” feature is selected, all doors will lock automatically when the vehicle reaches a speed of
12 mph (20 km/h).

Auto Unlock On Exit

On

Off

NOTE:
When this feature is selected, all doors unlock when the vehicle is stopped, the transmission is in the PARK or NEU-
TRAL position and the driver’s door is opened.

Flash Lights With Lock

On

Off

Sound Horn With Lock

Off

1st Press

2nd Press

Sound Horn With Remote

Start

On

Off

10

MULTIMEDIA

523

Setting Name

Selectable Options

1st Press Of Key Fob Un-

locks

Driver Door

All Doors

NOTE:
When

⬙Driver Door⬙ is selected with 1st Press Of Key Fob Unlocks, only the driver’s door will unlock with the first

press of the key fob unlock button. You must push the key fob unlock button twice to unlock the passenger’s doors.
When

⬙All Doors⬙ is selected for 1st Press Of Key Fob Unlocks, all doors will unlock on the first push of the key fob

unlock button. If the vehicle is programmed 1st Press Of Key Fob Unlocks “All Doors,” all doors will unlock no mat-
ter which Passive Entry equipped door handle is grasped. If 1st Press Of Key Fob Unlocks “Driver Door” is pro-
grammed, only the driver’s door will unlock when the driver’s door is grasped. With Passive Entry, if 1st Press Of
Key Fob Unlocks “Driver Door” is programmed, touching the handle more than once will result in only the driver’s
door opening. If “Driver Door” is selected, once the driver door is opened, the interior door lock/unlock switch can
be used to unlock all doors (or use the key fob).

Passive Entry — If

Equipped

On

Off

NOTE:
This feature allows you to lock and unlock the vehicles door(s) without having to push the key fob lock or unlock
buttons.

524

MULTIMEDIA