Lincoln Mark LT (2008 year). Instruction — part 20
BRAKE FLUID
The fluid level will drop slowly as
the brakes wear, and will rise when
the brake components are replaced.
Fluid levels between the “MIN” and
“MAX” lines are within the normal
operating range; there is no need to
add fluid. If the fluid levels are
outside of the normal operating
range the performance of the
system could be compromised; seek
service from your authorized dealer
immediately.
TRANSMISSION FLUID
Checking automatic transmission fluid
Refer to your scheduled maintenance information for scheduled
intervals for fluid checks and changes. Your transmission does not
consume fluid. However, the fluid level should be checked if the
transmission is not working properly, i.e., if the transmission slips or
shifts slowly or if you notice some sign of fluid leakage.
Automatic transmission fluid expands when warmed. To obtain an
accurate fluid check, drive the vehicle until it is at normal operating
temperature (approximately 20 miles [30 km]). If your vehicle has been
operated for an extended period at high speeds, in city traffic during hot
weather or pulling a trailer, the vehicle should be turned off for about 30
minutes to allow fluid to cool before checking.
1. Drive the vehicle 20 miles (30 km) or until it reaches normal operating
temperature.
2. Park the vehicle on a level surface and engage the parking brake.
3. With the parking brake engaged and your foot on the brake pedal,
start the engine and move the gearshift lever through all of the gear
ranges. Allow sufficient time for each gear to engage.
4. Latch the gearshift lever in P (Park) and leave the engine running.
5. Remove the dipstick, wiping it clean with a clean, dry lint free rag. If
necessary, refer to Identifying components in the engine compartment
in this chapter for the location of the dipstick.
6. Install the dipstick making sure it is fully seated in the filler tube.
2008 Mark LT (mlt)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
305
-------------------------------------------------------------------------------------------------------------------------------------------------------------
7. Remove the dipstick and inspect the fluid level. The fluid should be in
the designated area for normal operating temperature or ambient
temperature.
Low fluid level
Do not drive the vehicle if the fluid
level is at the bottom of the dipstick
and the ambient temperature is
above 50°F (10°C).
Correct fluid level
The transmission fluid should be checked at normal operating temperature
150°F-170°F (66°C-77°C) on a level surface. The normal operating
temperature can be reached after approximately 20 miles (30 km) of
driving.
You can check the fluid without driving if the ambient temperature is
above 50°F (10°C). However, if fluid is added at this time, an overfill
condition could result when the vehicle reaches normal operating
temperature.
The transmission fluid should be in
this range if at normal operating
temperature (150°F-170°F
[66°C-77°C]).
The transmission fluid should be in
this range if at ambient temperature
(50°F-95°F [10°C-35°C]).
High fluid level
Fluid levels above the safe range
may result in transmission failure.
An overfill condition of transmission
fluid may cause shift and/or
engagement concerns and/or
possible damage.
High fluid levels can be caused by an overheating condition.
Adjusting automatic transmission fluid levels
Before adding any fluid, make sure the correct type is used. The type of
fluid used is normally indicated on the dipstick. Refer to Maintenance
product specifications and capacities in this chapter.
2008 Mark LT (mlt)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
306
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Use of a non-approved automatic transmission fluid may cause
internal transmission component damage.
If necessary, add fluid in 1/2 pint (250 ml) increments through the filler
tube until the level is correct.
If an overfill occurs, excess fluid
should be removed by an authorized
dealer.
An overfill condition of
transmission fluid may cause shift and/or engagement concerns
and/or possible damage.
Do not use supplemental transmission fluid additives, treatments or
cleaning agents. The use of these materials may affect transmission
operation and result in damage to internal transmission components.
TRANSFER CASE FLUID (IF EQUIPPED)
1. Clean the filler plug.
2. Remove the filler plug and
inspect the fluid level.
2008 Mark LT (mlt)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
307
-------------------------------------------------------------------------------------------------------------------------------------------------------------
3. Add only enough fluid through
the filler opening so that the fluid
level is at the bottom of the
opening.
Use only fluid that meets Ford specifications. Refer to the Maintenance
product specifications and capacities section in this chapter.
DRIVELINE UNIVERSAL JOINT AND SLIP YOKE
Your vehicle may be equipped with universal joints that require
lubrication. Refer to the scheduled maintenance information for
maintenance intervals. If the original universal joints are replaced with
universal joints equipped with grease fittings, lubrication will also be
necessary.
AIR FILTER
Refer to scheduled maintenance information for the appropriate
intervals for changing the air filter element.
When changing the air filter element, use only the Motorcraft air filter
element listed. Refer to Motorcraft part numbers in this chapter.
To reduce the risk of vehicle damage and/or personal burn
injuries do not start your engine with the air cleaner removed
and do not remove it while the engine is running.
2008 Mark LT (mlt)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
308
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Changing the air filter element
1. Release two retainer clamps.
2. Pull air filter tray assembly out
toward front of vehicle and lift air
filter element up and out of housing.
The air filter box needs to be free of any debris before installing a new
air filter.
3. Install a new air filter element
into the tray assembly.
4. Return air filter tray to original
position by pressing firmly on the
handle until all rearward movement
stops and secure the two clamps.
Note: Failure to use the correct air filter element may result in severe
engine damage. The customer warranty may be void for any damage to
the engine if the correct air filter element is not used.
2008 Mark LT (mlt)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
309
-------------------------------------------------------------------------------------------------------------------------------------------------------------
MOTORCRAFT PART NUMBERS
Component
5.4L 3V V8 engine
Air filter element
FA-1754
Battery
BXT-65-650
Fuel filter
FG-986B
Oil filter
FL-820-S
PCV valve
1
Spark plugs
2
1
The PCV valve is a critical emission component. It is one of the items
listed in scheduled maintenance information and is essential to the
life and performance of your vehicle and to its emissions system.
For PCV valve replacement, see your authorized dealer. Refer to
scheduled maintenance information for the appropriate intervals for
changing the PCV valve.
Replace the PCV valve with one that meets Ford material and
design specifications for your vehicle, such as a Motorcraft or
equivalent replacement part. The customer warranty may be void
for any damage to the emissions system if such a PCV valve is not
used.
2
For spark plug replacement, see your authorized dealer. Refer to
scheduled maintenance information for the appropriate intervals for
changing the spark plugs.
Replace the spark plugs with ones that meet Ford material and
design specifications for your vehicle, such as Motorcraft or
equivalent replacement parts. The customer warranty may be
void for any damage to the engine if such spark plugs are not
used.
2008 Mark LT (mlt)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
310
-------------------------------------------------------------------------------------------------------------------------------------------------------------
MAINTENANCE
PRODUCT
SPECIFICATIONS
AND
CAPACITIES
Item
Capacity
Ford
part
name
or
equivalent
Ford
part
number
/
Ford
specification
Brake
fluid
Between
MIN
and
MAX
on
reservoir
Motorcraft
High
Performance
DOT
3
Motor
V
ehicle
Brake
Fluid
PM-1-C
/
WSS-M6C62-A
Seat
tracks
—
Multi-Purpose
Grease
XG-4
or
XL-5
/
ESB-M1C93-B
Hinges,
latches,
striker
plates,
fuel
filler
door
hinge
and
door
check
arm
—
Motorcraft
Silicone
Brake
Caliper
Grease
and
Dielectric
Compound
XG-3-A
/
ESE-M1C171-A
T
ransmission
/steering/parking
brake
linkages
and
pivots
and
brake
pedal
shaft
—
Premium
Long-Life
Grease
XG-1-C
/
ESA-M1C75-B
Lock
cylinders
—
Motorcraft
Penetrating
and
Lock
Lubricant
XL-1
/
None
Engine
oil
7.0
quarts
(6.6L)
Motorcraft
SAE
5W
-20
Premium
Synthetic
Blend
Motor
Oil
Motorcraft
SAE
5W
-20
Super
Premium
Motor
Oil
(Canada)
1
XO-5W20-QSP
(US)
CXO-5W20–LSP12
(Canada)
/
WSS-M2C930-A
with
API
Certification
Mark
2008 Mark LT (mlt)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
311
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Item
Capacity
Ford
part
name
or
equivalent
Ford
part
number
/
Ford
specification
Engine
coolant
21.2
quarts
(20.0L)
Motorcraft
Premium
Gold
Engine
Coolant
with
bittering
agent
(yellow-colored)
2
VC-7-B
/
WSS-M97B51-A1
Cooling
system
stop
leak
pellets
—
Motorcraft
Cooling
System
Stop
Leak
Pellets
VC-6
/
WSS-M99B37-B6
Front
axle
(4X4)
fluid
3.7
pints
(2.0L)
Motorcraft
SAE
80W
-90
Premium
Rear
Axle
Lubricant
XY
-80W90-QL
/
WSP-M2C197-A
Rear
axle
fluid–
9.75
inch
3
5.5
pints
(2.6L)
4
Motorcraft
SAE
75W
-140
Synthetic
Rear
Axle
Lubricant
XY
-75W140-QL
/
WSL-M2C192-A
Automatic
transmission
fluid
(4R75E)
13.9
quarts
(13.2L)
5
Motorcraft
MERCON
威
V
AT
F
6
XT
-5-QM
/
MERCON
威
V
Power
steering
fluid
Fill
to
between
MIN
and
MAX
lines
on
reservoir
Motorcraft
MERCON
威
V
AT
F
XT
-5-QM
/
MERCON
威
V
T
ransfer
case
fluid
(4X4)
2.0
quarts
(1.9L)
7
Motorcraft
T
ransfer
Case
Fluid
XL-12
/
—
W
indshield
washer
fluid
4.25
quarts
(4.0L)
Motorcraft
Premium
W
indshield
W
asher
Concentrate
ZC-32-A
/
WSB-M8B16-A2
Fuel
tank
(5.5’
box)
30.0
gallons
(113.6L)
——
2008 Mark LT (mlt)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
312
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Item
Capacity
Ford
part
name
or
equivalent
Ford
part
number
/
Ford
specification
Fuel
tank
(6.5’
box)
27.0
gallons
(102.2L)
Standard
35.7
gallons
(135.1L)
Optional
——
1
Use
of
synthetic
or
synthetic
blend
motor
oil
is
not
mandatory
.
Engine
oil
need
only
meet
the
requirements
of
Ford
specification
WSS-M2C930-A
and
the
API
Certification
mark.
2
Add
the
coolant
type
originally
equipped
in
your
vehicle.
3
Y
our
vehicle’
s
rear
axle
is
filled
with
a
synthetic
rear
axle
lubricant
and
is
considered
lubricated
for
life.
These
lubricants
do
not
need
to
be
checked
or
changed
unless
a
leak
is
suspected,
service
is
required
or
the
axle
assembly
has
been
submerged
in
water
.
The
axle
lubricant
should
be
changed
any
time
the
rear
axle
has
been
submerged
in
water
.
4
Service
refill
capacity
is
determined
by
filling
the
axle
to
1/4-9/16
inch
(6-14
mm)
below
the
bottom
of
the
filler
hole
with
the
vehicle
on
a
level
surface.
Add
4
oz.
(118
ml)
of
Additive
Friction
Modifier
or
equivalent
meeting
Ford
specification
EST
-M2C118-A,
for
complete
fill
of
9.75
inch
T
raction-Lok
axles.
5
Approximate
dry
fill
capacity
including
transmission
fluid
cooling
system,
actual
refill
capacities
will
vary
based
on
vehicle
application
and
transmission
fluid
cooling
system
(i.e.
coolers
size,
cooling
lines,
auxiliary
cooler
capacities).
The
amount
of
transmission
fluid
and
fluid
level
should
be
set
by
the
indication
on
the
dipstick’
s
normal
operating
range.
6
Automatic
transmissions
that
require
MERCON
威
V
should
only
use
MERCON
威
V
fluid
or
fluid
that
is
specified
dual
usage
MERCON
威
/MERCON
威
V
.
Use
of
any
fluid
other
than
the
recommended
fluid
may
cause
transmission
damage.
Refer
to
scheduled
maintenance
information
to
determine
the
correct
service
interval.
Use
of
any
fluid
other
than
the
recommended
fluid
may
cause
transmission
damage.
7
Service
refill
capacity
is
determined
by
filling
the
transfer
case
to
the
bottom
of
the
filler
hole
with
the
vehicle
on
a
level
surface.
2008 Mark LT (mlt)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
313
-------------------------------------------------------------------------------------------------------------------------------------------------------------
ENGINE DATA
Engine
5.4L V8 engine
Cubic inches
330
Required fuel
87 octane
Firing order
1-3-7-2-6-5-4-8
Ignition system
Coil on plug
Spark plug gap
1
0.040–0.050 inch (1.02–1.28mm)
Compression ratio
9.85:1
1
The spark plug gap can not be adjusted.
2008 Mark LT (mlt)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
314
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Engine drivebelt routing
IDENTIFYING YOUR VEHICLE
Safety Compliance Certification Label
The National Highway Traffic Safety
Administration Regulations require
that a Safety Compliance
Certification Label be affixed to a
vehicle and prescribe where the
Safety Compliance Certification
Label may be located. The Safety
Compliance Certification Label is
located on the structure (B-Pillar)
by the trailing edge of the driver’s
door or the edge of the driver’s
door.
2008 Mark LT (mlt)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
315
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Vehicle identification number (VIN)
The vehicle identification number is
located on the driver side
instrument panel.
Please note that in the graphic,
XXXX is representative of your
vehicle identification number.
The Vehicle Identification Number (VIN) contains the following
information:
1. World manufacturer identifier
2. Brake system / Gross Vehicle
Weight Rating (GVWR) / Restraint
System
3. Vehicle line, series, body type
4. Engine type
5. Check digit
6. Model year
7. Assembly plant
8. Production sequence number
XXXXXXXXXXXXXXXXX
2008 Mark LT (mlt)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
316
-------------------------------------------------------------------------------------------------------------------------------------------------------------
TRANSMISSION/TRANSAXLE CODE DESIGNATIONS
You can find a
transmission/transaxle code on the
Safety Compliance Certification
Label. The following table tells you
which transmission or transaxle
each code represents.
Description
Code
Four-speed automatic (4R75E)
Q
2008 Mark LT (mlt)
Owners Guide (post-2002-fmt)
USA (fus)
Maintenance and Specifications
317
-------------------------------------------------------------------------------------------------------------------------------------------------------------
GENUINE LINCOLN ACCESSORIES FOR YOUR VEHICLE
A wide selection of Genuine Lincoln Accessories are available for your
vehicle through your local Lincoln or Ford of Canada dealer. These
quality accessories have been specifically engineered to fulfill your
automotive needs; they are custom designed to complement the style
and aerodynamic appearance of your vehicle. In addition, each accessory
is made from high quality materials and meets or exceeds Lincoln’s
rigorous engineering and safety specifications. Ford Motor Company will
repair or replace any properly dealer-installed Genuine Lincoln
Accessories found to be defective in factory-supplied materials or
workmanship during the warranty period, as well as any component
damaged by the defective accessories. The accessories will be warranted
for whichever provides you the greatest benefit:
• 12 months or 12,000 miles (20,000 km) (whichever occurs first), or
• the remainder of your new vehicle limited warranty.
Contact your dealer for details and a copy of the warranty.
Following is a list of several Genuine Lincoln Accessories. Not all
accessories are available for all models. To find out what accessories are
available for your vehicle, please contact your dealer or visit our online
store at: www.lincolnaccessories.com.
Exterior style
Bug shields
Chrome exhaust tips
Deflectors
Running boards
Splash guards
Step bars
Tonneau covers
Wheels
Interior style
Electrochromatic compass/temperature interior mirrors
Floor mats
2008 Mark LT (mlt)
Owners Guide (post-2002-fmt)
USA (fus)
Accessories
318
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Lifestyle
Ash cup / smoker’s package
Bedliners and bedmats
Cargo organization and management
Towing mirrors
Trailer hitches, wiring harnesses and accessories
Peace of mind
Mobile-ease™ hands-free communication system
Remote start
Vehicle security systems
Wheel locks
For maximum vehicle performance, keep the following information in
mind when adding accessories or equipment to your vehicle:
• When adding accessories, equipment, passengers and luggage to your
vehicle, do not exceed the total weight capacity of the vehicle or of
the front or rear axle (GVWR or GAWR as indicated on the Safety
Compliance Certification label). Consult your authorized dealer for
specific weight information.
• The Federal Communications Commission (FCC) and Canadian Radio
Telecommunications Commission (CRTC) regulate the use of mobile
communications systems — such as two-way radios, telephones and
theft alarms - that are equipped with radio transmitters. Any such
equipment installed in your vehicle should comply with FCC or CRTC
regulations and should be installed only by a qualified service
technician.
• Mobile communications systems may harm the operation of your
vehicle, particularly if they are not properly designed for automotive
use.
• To avoid interference with other vehicle functions, such as anti-lock
braking systems, amateur radio users who install radios and antennas
onto their vehicle should not locate the Amateur Radio Antennas in
the area of the driver’s side hood.
• Electrical or electronic accessories or components that are added to
the vehicle by the authorized dealer or the owner may adversely affect
battery performance and durability.
2008 Mark LT (mlt)
Owners Guide (post-2002-fmt)
USA (fus)
Accessories
319
-------------------------------------------------------------------------------------------------------------------------------------------------------------
A
Accessory delay . . . . . . ..89
Air cleaner filter . . . ...308–310
Air conditioning . . . . . . ..68
Airbag supplemental restraint
system . . . . . . . . 155–156
and child safety seats . . . 158
description . . . . . . . ..156
disposal . . . . . . . . . 160
driver airbag . . . . . 156, 158
indicator light . . . . . . .159
operation . . . . . . .156, 158
passenger airbag . . . .156, 158
Ambulance packages . . . . . 8
Antifreeze
(see Engine coolant) . . . . 287
Anti-lock brake system
(see Brakes) . . . . . . . ..215
Anti-theft system . . . . . ..131
arming the system . . . . ..132
Audio system (see Radio) ...19, 23
Automatic transmission
driving an automatic
overdrive . . . . . . . . .221
fluid, adding . . . . . . . 305
fluid, checking . . . . . . 305
fluid, refill capacities . . . ..311
fluid, specification . . . . ..311
Auxiliary input jack (Line in) . 31
Axle
lubricant specifications . . ..311
refill capacities . . . . . . 311
traction lok . . . . . . . ..218
B
Battery . . . . . . . . . ...285
acid, treating emergencies . .285
jumping a disabled battery . 255
maintenance-free . . . . . 285
replacement, specifications ...310
servicing . . . . . . . . ..285
deactivating/activating the
Belt-Minder
Booster seats . . . . . . . .164
Brakes . . . . . . . . . . 215
anti-lock . . . . . . . . ...215
anti-lock brake system (ABS)
warning light . . . . . . ...215
fluid, checking and adding . 305
fluid, refill capacities . . . ..311
fluid, specifications . . . . .311
lubricant specifications . . ..311
parking . . . . . . . . . 216
shift interlock . . . . . . ..219
Bulbs . . . . . . . . . . . 77
C
Capacities for refilling fluids . 311
Cargo cage . . . . . . . . .112
Cargo management system . ..114
Cell phone use . . . . . . . ..9
Changing a tire . . . . . . .247
Child safety restraints . . . ..164
child safety belts . . . . . 164
Child safety seats . . . . . ..167
attaching with tether straps ..171
in front seat . . . . . . . 169
in rear seat . . . . . . . ..169
Child safety seats - booster
seats . . . . . . . . . . ...164
Cleaning your vehicle
engine compartment . . . ..273
2008 Mark LT (mlt)
Owners Guide (post-2002-fmt)
USA (fus)
Index
320
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст