Lincoln LS (2006 year). Instruction — part 8
Navigation control features
Press and hold VOICE until the
voice
icon appears to use the
navigation voice guidance.
Press REPEAT control to hear
previous command repeated from
the navigation system.
MOON ROOF (IF EQUIPPED)
To open the moon roof:
• Push up on the control to raise
the moon roof to the vent
position.
• Push up on the control, while the
moon roof is in the slide range, to
activate the Auto-Tilt feature.
• Push the front portion of the
control rearward to open the
moon roof.
• Press the front portion of the
control past the first detent to activate the Auto Open feature.
To close the moon roof:
• Press the rear portion of the control forward to close the moon roof.
• Press the rear portion of the control past the first detent to activate
the Auto close feature.
2006 Lincoln LS (dew)
Owners Guide (post-2002-fmt)
USA (fus)
Driver Controls
120
-------------------------------------------------------------------------------------------------------------------------------------------------------------
• To close from the vent, intermediate and full open positions, push the
rear portion of the control forward.
Do not let children play with the moon roof or leave children
unattended in the vehicle. They may seriously hurt themselves.
When closing the moon roof, you should verify it is free of
obstructions and ensure that children and/or pets are not in the
proximity of the window openings.
Bounce Back
When an obstacle has been detected in the moon roof opening as the
moon roof is closing, the moon roof will automatically open and stop at a
prescribed position.
Bounce Back Override
To override Bounce Back, within 2 seconds after reaching Bounce Back
position, if the switch is moved from the Neutral to the auto close
position the moon roof will close with no bounce back protection.
If the switch is released before the moon roof reaches fully closed
position, the moon roof will stop. For example: Bounce Back Override
can be used to overcome the resistance of ice on the moon roof or seals.
HOMELINK
姞
WIRELESS CONTROL SYSTEM (IF EQUIPPED)
The HomeLink
威 Wireless Control System, located on the driver’s visor,
provides a convenient way to replace up to three hand-held transmitters
with a single built-in device. This feature will learn the radio frequency
codes of most transmitters to operate garage doors, entry gate operators,
security systems, entry door locks, and home or office lighting.
When programming your HomeLink
威 Wireless Control System to
a garage door or gate, be sure that people and objects are out of
the way to prevent potential harm or damage.
Do not use the HomeLink
威 Wireless Control System with any garage
door opener that lacks safety stop and reverse features as required by
U.S. federal safety standards (this includes any garage door opener
model manufactured before April 1, 1982). A garage door which cannot
detect an object, signaling the door to stop and reverse, does not meet
current U.S. federal safety standards. For more information, contact
HomeLink
威 at: www.homelink.com or 1–800–355–3515.
2006 Lincoln LS (dew)
Owners Guide (post-2002-fmt)
USA (fus)
Driver Controls
121
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Retain the original transmitter for use in other vehicles as well as for
future programming procedures (i.e. new HomeLink
威 equipped vehicle
purchase). It is also suggested that upon the sale of the vehicle, the
programmed Homelink
威 buttons be erased for security purposes, refer to
Programming in this section.
Programming
Do not program HomeLink
威 with the vehicle parked in the garage.
Note: Your vehicle may require the ignition switch to be turned to the
ACC position for programming and/or operation of the HomeLink
威. It is
also recommended that a new battery be placed in the hand-held
transmitter of the device being programmed to HomeLink
威 for quicker
training and accurate transmission of the radio-frequency signal.
1. Press and hold the two outside
buttons releasing only when the
indicator light begins to flash after
20 seconds. Do not repeat Step 1
to program additional hand-held
transmitters to the remaining two
HomeLink
威 buttons. This will erase
previously programmed hand-held
transmitter signals into HomeLink
威.
2. Position the end of your
hand-held transmitter 1–3 inches (2–8 cm) away from the HomeLink
威
button you wish to program (located on your visor) while keeping the
indicator light in view.
3. Simultaneously press and hold
both the HomeLink
威 and hand-held
transmitter button. Do not release
the buttons until Step 4 has
been completed.
Some entry gates and garage door
openers may require you to replace
Step 3 with procedures noted in the
“Gate Operator and Canadian Programming” in this section for Canadian
residents.
4. The indicator light will flash slowly and then rapidly. Release both
buttons when the indicator light flashes rapidly. (The rapid flashing light
indicates acceptance of the hand-held transmitters’ radio frequency
signals.)
2006 Lincoln LS (dew)
Owners Guide (post-2002-fmt)
USA (fus)
Driver Controls
122
-------------------------------------------------------------------------------------------------------------------------------------------------------------
5. Press and hold the just-trained HomeLink
威 button and observe the
indicator light. If the light is constant, programming is complete and your
device should activate when the HomeLink
威 button is pressed and
released. Note: To program the remaining two HomeLink
威 buttons,
begin with Step 2 in the “Programming” section — do not repeat Step 1.
Note: If the indicator light blinks rapidly for two seconds and then turns
to a continuous red, proceed with Steps 6 through 8 to complete
programming of a rolling code equipped device.
6. At the garage door opener receiver (motor-head unit) in the garage,
locate the “learn” or “smart” button (usually near where the hanging
antenna wire is attached to the unit).
7. Press and release the “learn” or “smart” button. (The name and color
of the button may vary by manufacturer.)
Note: There are 30 seconds in which to initiate Step 8.
8. Return to the vehicle and firmly press, hold for two seconds and
release the HomeLink
威 button. Repeat the press/hold/release sequence
again, and, depending on the brand of the garage door opener (or other
rolling code equipped device), repeat this sequence a third time to
complete the programming.
HomeLink
威 should now activate your rolling code equipped device. To
program additional HomeLink
威 buttons begin with Step 2 in the
“Programming” section. For questions or comments, please contact
HomeLink at www.homelink.com or 1–800–355–3515.
Gate Operator & Canadian Programming
During programming, your
hand-held transmitter may
automatically stop transmitting —
not allowing enough time for
HomeLink
威 to accept the signal
from the hand-held transmitter.
After completing Steps 1 and 2
outlined in the “Programming”
section, replace Step 3 with the following:
Note: If programming a garage door opener or gate operator, it is
advised to unplug the device during the “cycling” process to prevent
overheating.
• Continue to press and hold the HomeLink威 button (note Step 3 in the
“Programming” section) while you press and release — every two
2006 Lincoln LS (dew)
Owners Guide (post-2002-fmt)
USA (fus)
Driver Controls
123
-------------------------------------------------------------------------------------------------------------------------------------------------------------
seconds (“cycle”) your hand-held transmitter until the frequency
signal has been accepted by the HomeLink
威. The indicator light will
flash slowly and then rapidly after HomeLink
威 accepts the radio
frequency signal.
• Proceed with Step 4 in the “Programming” section.
Operating the HomeLink
姞
Wireless Control System
To operate, simply press and release
the appropriate HomeLink
威 button.
Activation will now occur for the
trained product (garage door, gate
operator, security system, entry
door lock, or home or office lighting
etc.). For convenience, the
hand-held transmitter of the device
may also be used at any time. In the event that there are still
programming difficulties, contact HomeLink
威 at www.homelink.com or
1–800–355–3515.
Erasing HomeLink
姞
buttons
To erase the three programmed
buttons (individual buttons cannot
be erased):
• Press and hold the two outer
HomeLink
威 buttons until the
indicator light begins to
flash-after 20 seconds. Release
both buttons. Do not hold for
longer that 30 seconds.
HomeLink
威 is now in the train (or
learning) mode and can be programmed at any time beginning with Step
2 in the “Programming” section.
Reprogramming a single HomeLink
姞
button
To program a device to HomeLink
威 using a HomeLink威 button previously
trained, follow these steps:
1. Press and hold the desired HomeLink
威 button. Do NOT release the
button.
2. The indicator light will begin to flash after 20 seconds. Without
releasing the HomeLink
威 button, follow Step 2 in the “Programming”
section.
2006 Lincoln LS (dew)
Owners Guide (post-2002-fmt)
USA (fus)
Driver Controls
124
-------------------------------------------------------------------------------------------------------------------------------------------------------------
For questions or comments, contact HomeLink
威 at www.homelink.com
or 1–800–355–3515.
MINI MESSAGE CENTER (IF EQUIPPED)
The instrument cluster is equipped with a warning center that will
provide the following warning messages:
Bulb warning: Displays when one
of the exterior front turn/park lamps
or rear brake/turn/tail lamps bulb
has burned out. Depress the RESET
control to return to the Trip odometer display.
Park brake ON: Displayed when
the park brake is ON. If the warning
stays on after the park brake is off,
contact your authorized dealer as
soon as possible.
Park brake ON & needs service:
Displayed when the park brake is
ON and malfunctioning. If the
warning stays on or continues to
come on, contact your authorized dealer as soon as possible.
Service park brake: Displayed
when the park brake needs
servicing. If the warning stays on or
continues to come on, contact your
authorized dealer as soon as possible.
Apply park brake: Displayed when
the park brake needs to be applied.
If the warning stays on or continues
to come on, contact your authorized
dealer as soon as possible.
Foot on brake: Displayed when the
foot brake needs to be applied. If
the warning stays on or continues to
come on, contact your authorized
dealer as soon as possible.
2006 Lincoln LS (dew)
Owners Guide (post-2002-fmt)
USA (fus)
Driver Controls
125
-------------------------------------------------------------------------------------------------------------------------------------------------------------
MESSAGE CENTER (IF EQUIPPED)
With the ignition in the RUN
position, the message center,
located on your instrument cluster,
displays important vehicle
information by monitoring vehicle
systems. When you change displays,
a brief indicator chime will sound. The system will also notify you of
potential vehicle problems with a system warnings display followed by a
long indicator chime.
Operator selectable features
These features are controlled by the message center controls located
above the radio.
FUEL
Press this control for the following displays:
• Distance to Empty
• Average Fuel Economy
• Display On/Off
RESET
Press this control to select and reset functions shown in the FUEL,
SETUP and STATUS controls.
SETUP
Press this control for the following displays:
• Units (English/Metric)
• Autolocks
• Easy Exit Seat (if equipped)
• Autolamp Delay
• Lock Chirp (if equipped)
• Language
STATUS
Selecting this function from the STATUS control causes the message
center to cycle through each of the systems being monitored. For each
of the monitored systems, the message center will indicate either an OK
message or a warning message for four seconds.
160
240
km/h
E
FUEL
RESET
SETUP
STATUS
2006 Lincoln LS (dew)
Owners Guide (post-2002-fmt)
USA (fus)
Driver Controls
126
-------------------------------------------------------------------------------------------------------------------------------------------------------------
The sequence of the status check report is as follows:
• washer fluid level
• oil life in XX%
• AC (cabin) filter XX%
• engine temperature
• brake fluid level
• charging system
• doors closed (driver and passenger side, front and rear). This message
can only be reset by closing the door(s). If the RESET control is
pressed, PLEASE CLOSE DOOR will be displayed.
• trunk status
• exterior lamps (front and rear turn, brake, tail and side repeater lamp
(if equipped) status)
• Traction Control娂 or AdvanceTrac娂 (if equipped)
Message center functions
Dist To Empty (DTE)
Selecting this function from the
FUEL control estimates
approximately how far you can drive
with the fuel remaining in your tank
under normal driving conditions.
Remember to turn the ignition OFF when refueling to allow this feature
to correctly detect the added fuel.
The DTE function will display LOW FUEL LEVEL and sound a tone for
one second when you have approximately 50 miles (80 km) to empty. If
you RESET this warning message, this display and tone will return
within 10 minutes.
DTE is calculated using a running average fuel economy, which is based
on your recent driving history of 500 miles (800 km). This value is not
the same as the average fuel economy display. The running average fuel
economy is reinitialized to a factory default value if the battery is
disconnected.
2006 Lincoln LS (dew)
Owners Guide (post-2002-fmt)
USA (fus)
Driver Controls
127
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Fuel Econ Avg
Select this function from the FUEL
control to display your average fuel
economy in miles/gallon or liters/100
km.
If you calculate your average fuel
economy by dividing gallons of fuel used by 100 miles traveled
(kilometers traveled by liters used), your figure may be different than
displayed for the following reasons:
• your vehicle was not perfectly level during fill-up
• differences in the automatic shut-off points on the fuel pumps at
service stations
• variations in top-off procedure from one fill-up to another
• rounding of the displayed values to the nearest gallon (liter)
Checking your highway fuel economy using the electronic
message center display
The following procedure will allow you to accurately monitor your actual
highway fuel economy. Since this procedure requires the vehicle speed
control system to be set to highway speeds, it must be run only on
suitable roadways where long distance speed control can be safely
maintained.
You may notice gradual improvement in fuel economy over the course of
your vehicle’s break-in period (approximately 1,000 miles [1,600
kilometers]).
1. Press the FUEL control to display
miles to empty. Press again to
display average fuel economy.
2. Set the speed control. Refer to
Speed control in this chapter.
3. Press the RESET control to clear the system memory.
• Actual highway fuel economy is now displayed. This current
average measure will change as the speed control system changes the
engine speed to maintain a constant vehicle speed. This is most
noticeable in hilly environments.
4. Drive the vehicle at least 5 miles (8 km) with the speed control
system engaged to display a stabilized average.
5. Record the highway fuel economy for future reference.
2006 Lincoln LS (dew)
Owners Guide (post-2002-fmt)
USA (fus)
Driver Controls
128
-------------------------------------------------------------------------------------------------------------------------------------------------------------
It is important to press the RESET control after setting the speed
control to get accurate highway fuel economy readings.
Display On/Off
Select this function from the FUEL control to turn your message center
display OFF or ON.
Units (English/Metric)
1. Select this function from the
SETUP control for the current units
to be displayed.
2. Press the RESET control to
change from English to Metric.
Autolocks
1. Select this function from the
SETUP control for the current
display mode.
2. Press the RESET control to turn
the autolocks ON or OFF.
Easy exit seat (if equipped)
1. Select this function from the
SETUP control for the current
display mode.
2. Press the RESET control to turn
the easy entry/exit ON or OFF.
Autolamp delay
1. Select this function from the
SETUP control for the current
display mode.
2. Press the RESET control to select
a new Autolamp delay value.
Lock chirp (if equipped)
1. Select this function from the
SETUP control for the current
display mode.
2. Press the RESET control to turn
the lock chirp ON or OFF.
2006 Lincoln LS (dew)
Owners Guide (post-2002-fmt)
USA (fus)
Driver Controls
129
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Language
1. Select this function from the
SETUP control for the current
language to be displayed.
2. Pressing the RESET control
cycles the message center through
each of the language choices.
3. Press and hold the RESET
control to set the language choice.
System warnings
System warnings alert you to possible problems or malfunctions in your
vehicle’s operating systems.
In the event of a multiple warning situation, the message center will
cycle the display to show all warnings by displaying each one for 4
seconds.
The message center will display the last selected feature if there are no
more warning messages. This allows you to use the full functionality of
the message center after you acknowledge the warning by pressing the
RESET control and clearing the warning message.
Warning messages that have been reset are divided into two categories:
• They will reappear on the display ten minutes from the reset.
• They will not reappear until an ignition OFF-RUN cycle has been
completed.
This acts as a reminder that these warning conditions still exist within
the vehicle.
2006 Lincoln LS (dew)
Owners Guide (post-2002-fmt)
USA (fus)
Driver Controls
130
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Warnings
Status
Engine power reduced
Warning cannot be reset
Pull off road safely
Turn off ignition
Driver’s door ajar
Passenger door ajar
Driver rear door ajar
Passenger rear door ajar
Park brake on & need service
Park brake on
Check engine temp
Warning returns after 10 minutes
Check charging system
Transmission overheated
Check transmission
Low fuel level
Check fuel cap
ETC-engine failsafe mode
2006 Lincoln LS (dew)
Owners Guide (post-2002-fmt)
USA (fus)
Driver Controls
131
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Warnings
Status
Low brake fluid level
Warning returns after the ignition key
is turned from OFF to RUN
Check tail lamps
Check brake lamps
Check front turn lamps
Check side repeater lamps (if
equipped)
Check rear turn lamps
Check Traction Control
Check AdvanceTrac
威 (if
equipped)
Trunk ajar
Low washer fluid
Check AC (cabin) filter
Change oil soon
Oil change required
Service park brake
Apply park brake
Foot on brake
Data error
ENGINE POWER REDUCED. Displayed when the engine is
overheating. Stop the vehicle as soon as safely possible and turn off the
engine. If this warning stays on, contact your authorized dealer as soon
as possible.
PULL OFF ROAD SAFELY. Displayed when the engine is overheating.
Stop the vehicle as soon as safely possible and turn off the engine. If this
warning stays on, contact your authorized dealer as soon as possible.
TURN OFF IGNITION. Displayed when the engine is overheating. Turn
off the engine. If this warning stays on, contact your authorized dealer as
soon as possible.
DRIVER’S DOOR AJAR. Displayed when the driver’s door is not
completely closed.
PASSENGER DOOR AJAR. Displayed when the passenger side door is
not completely closed.
DRIVER’S REAR DOOR AJAR. Displayed when the driver’s rear door
is not completely closed.
2006 Lincoln LS (dew)
Owners Guide (post-2002-fmt)
USA (fus)
Driver Controls
132
-------------------------------------------------------------------------------------------------------------------------------------------------------------
PASSENGER REAR DOOR AJAR. Displayed when the passenger side
rear door is not completely closed.
PARK BRAKE ON & NEED SERVICE. Displayed when the park brake
is ON and malfunctioning. If the warning stays on or continues to come
on, contact your authorized dealer as soon as possible.
PARK BRAKE ON. Displayed when the park brake is on. If the warning
stays on after the park brake is off, contact your authorized dealer as
soon as possible.
CHECK ENGINE TEMP. Displayed when the engine coolant is
overheating. Stop the vehicle as soon as safely possible, turn off the
engine and let it cool. Check the coolant and coolant level. Refer to
Engine coolant in the Maintenance and Specifications chapter. If the
warning stays on or continues to come on, contact your authorized
dealer as soon as possible.
Never remove the coolant reservoir cap while the engine is
running or hot.
CHECK CHARGING SYSTEM. Displayed when the electrical system is
not maintaining proper voltage. If you are operating electrical accessories
when the engine is idling at a low speed, turn off as many of the
electrical loads as soon as possible. If the warning stays on or comes on
when the engine is operating at normal speeds, have the electrical
system checked as soon as possible.
TRANSMISSION OVERHEATED. Indicates the transmission is
overheating. This warning may appear when driving in a low gear at a
high speed for an extended period of time. Stop the vehicle as soon as
safely possible, turn off the engine and let it cool. Check the
transmission fluid and level. Refer to Transmission fluid in the
Maintenance and Specifications chapter. If the warning stays on or
continues to come on, contact your authorized dealer for transmission
service as soon as possible.
CHECK TRANSMISSION. Indicates the transmission is not operating
properly. If this warning stays on, contact your authorized dealer as soon
as possible.
LOW FUEL LEVEL. Displayed when you have approximately 50 miles
(80 km) to empty.
CHECK FUEL CAP. Displayed when the fuel filler cap is not properly
installed. Check the fuel filler cap for proper installation. Refer to Fuel
filler cap in the Maintenance and Specifications chapter.
2006 Lincoln LS (dew)
Owners Guide (post-2002-fmt)
USA (fus)
Driver Controls
133
-------------------------------------------------------------------------------------------------------------------------------------------------------------
ETC-ENGINE FAILSAFE MODE. Displayed when the engine has
defaulted to a ’limp-home’ operation. If the warning stays on or continues
to come on, contact your authorized dealer as soon as possible.
LOW BRAKE FLUID. Indicates the brake fluid level is low and the
brake system should be inspected immediately. Refer to Brake fluid
reservoir in the Maintenance and Specifications chapter.
CHECK TAIL LAMPS. Displayed when the tail lamps are activated and
at least one is burned out. Check the lamps as soon as safely possible
and have the burned out lamp replaced.
CHECK BRAKE LAMPS. Displayed when the brake lamps are
activated and at least one is burned out. Check the lamps as soon as
safely possible and have the burned out lamp replaced. The center
high-mount brakelamp is not monitored.
CHECK FRT TURN LAMPS. Displayed when the turn signals are
activated and at least one is burned out. Check the lamps as soon as
safely possible and have the burned out lamp replaced.
CHECK SIDE REPEATER LAMPS (if equipped). Displayed when
the turn signals are activated and at least one is burned out. Check the
lamps as soon as possible and have the burned out lamp replaced.
CHECK REAR TURN LAMPS. Displayed when the turn signals are
activated and at least one is burned out. Check the lamps as soon as
possible and have the burned out lamp replaced.
CHECK TRACTION CONTROL. Displayed when the Traction
Control
娂 system is not operating properly. If this message is displayed
on the message center and the amber T/C OFF light in the Traction
Control
娂 on/off switch is not illuminated, the Traction Control娂 system
will be partially operable. If this warning stays on, contact your
authorized dealer for service as soon as possible. For further information,
refer to Traction control
娂 in the Driving chapter.
CHECK ADVANCETRAC (if equipped). Displayed when the
AdvanceTrac
威 system is not operating properly. If this message is
displayed on the message center the AdvanceTrac
威 system will be
partially operable. If this warning stays on while the engine is running,
contact your authorized dealer for service as soon as possible. For
further information, refer to AdvanceTrac
威 stability enhancement
system in the Driving chapter.
TRUNK AJAR. Displayed when the trunk is not completely closed.
LOW WASHER FLUID. Indicates the washer fluid reservoir is less than
one quarter full. Check the washer fluid level. Refer to Checking and
adding washer fluid in the Maintenance and Specifications chapter.
2006 Lincoln LS (dew)
Owners Guide (post-2002-fmt)
USA (fus)
Driver Controls
134
-------------------------------------------------------------------------------------------------------------------------------------------------------------
CHECK A/C (cabin) FILTER. Displayed when the A/C cabin filter life
remaining is 5 percent or less. When A/C filter life left is between 5%
and 0%, the CHANGE A/C FILTER SOON message will be displayed.
When A/C filter life left reaches 0%, the A/C FILTER CHANGE
REQUIRED message will be displayed.
To reset the A/C filter monitoring system to 100% after each A/C Filter
change:
1. Press the STATUS control to
access the System Check function,
the message center will display A/C
FILTER XXX% RESET FOR NEW.
2. Press and hold the RESET
control to set to 100%, the message
center will display IF NEW FILTER
HOLD RESET.
3. After a successful reset, the
message center will display A/C
FILTER LIFE SET TO 100%.
CHANGE OIL SOON/OIL CHANGE REQUIRED. Displayed when the
engine oil life remaining is 5 percent or less. When oil life left is between
5% and 0%, the CHANGE OIL SOON message will be displayed. When oil
life left reaches 0%, the OIL CHANGE REQUIRED message will be
displayed.
An oil change is required whenever indicated by the message center.
USE ONLY RECOMMENDED ENGINE OILS.
To reset the oil monitoring system to 100% after each oil change
[approximately 5,000 miles (8,000 km) or 180 days] perform the
following:
1. Press the STATUS control to
access the System Check function.
Press RESET to reset oil %.
2006 Lincoln LS (dew)
Owners Guide (post-2002-fmt)
USA (fus)
Driver Controls
135
-------------------------------------------------------------------------------------------------------------------------------------------------------------
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст