Toyota Corolla (2019 year). Manual — part 20
305
5-6. Using an external device
5
Audi
o system
COROLLA_TMMMS_TMMC_U
■
Operating portable audio players connected to Entune Audio
The volume can be adjusted using the vehicle's audio controls. All other
adjustments must be made on the portable audio player itself.
■
When using a portable audio player connected to the power outlet
Noise may occur during playback. Use the power source of the portable
audio player.
Using the AUX port
To use the AUX port, connect a portable player, press the
“AUDIO” button, then select “AUX” to display the audio control
screen.
Connecting a portable audio player
WARNING
■
While driving
Do not connect a portable audio player or operate the device controls.
306
COROLLA_TMMMS_TMMC_U
5-7. Connecting Bluetooth
®
■
About Bluetooth
®
Preparations to use wireless communica-
tion
The following can be performed using Bluetooth
®
wireless com-
munication:
■
A portable audio player can be operated and listened to via
Entune Audio
■
Hands-free phone calls can be made via a cellular phone
In order to use wireless communication, register and connect a
Bluetooth
®
device by performing the following procedures.
The Bluetooth
®
word mark and logos are
registered trademarks owned Bluetooth
SIG, Inc. and any use of such marks by
Fujitsu Ten Limited is under license.
Other trademarks and trade names are
those of their respective owners.
WARNING
■
Certifications for the Bluetooth
FCC ID: BABFT0077A
●
CAUTION: Radio Frequency Radiation Exposure
This equipment complies with FCC radiation exposure limits set forth for
uncontrolled equipment and meets the FCC radio frequency (RF) Expo-
sure Guidelines.
This equipment has very low levels of RF energy that it deemed to comply
without maximum permissive exposure evaluation (MPE). But it is desir-
able that it should be installed and operated with at least 20cm and more
between the radiator and person's body in normal use position.
• Co-location: This transmitter must not be co-located or operated in con-
junction with any other antenna or transmitter.
• This device complies with part 15 of the FCC Rules. Operation is sub-
ject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
307
5-7. Connecting Bluetooth
®
5
Audi
o system
COROLLA_TMMMS_TMMC_U
WARNING
●
FCC WARNING:
Changes or modifications not expressly approved by the party responsi-
ble for compliance could void the user's authority to operate the equip-
ment.
●
IC: 2024B-FT0077A
• This device complies with Industry Canada’s licence-exempt RSSs.
Operation is subject to the following two conditions: (1) This device may
not cause interference; and (2) This device must accept any interfer-
ence, including interference that may cause undesired operation of the
device.
●
CAUTION: Radio Frequency Radiation Exposure
This equipment complies with IC radiation exposure limits set forth for
uncontrolled equipment and meets RSS-102 of the IC radio frequency
(RF) Exposure rules.
This equipment has very low levels of RF energy that it deemed to comply
without maximum permissive exposure evaluation (MPE).
But it is desirable that it should be installed and operated with at least
20cm and more between the radiator and person's body (excluding
extremities: hands, wrists, feet and ankles).
●
IC: 2024B-FT0077A
• Le présent appareil est conforme aux CNR d'Industrie Canada appli-
cables aux appareils radio exempts de licence. L'exploitation est autori-
sée aux deux conditions suivantes : (1) l'appareil ne doit pas produire
de brouillage; (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compro-
mettre le fonctionnement.
●
ATTENTION: l'exposition aux rayonnements radiofréquence
- Cet équipement se conforme aux limites d’exposition aux radiations éta-
blies par Industrie Canada pour un environnement non contrôlé ainsi
qu’aux directives d’exposition aux fréquences radioélectriques (RF)
émises par Industrie Canada dans la norme CNR-102. Cet équipement
émet un niveau d’énergie RF faible à un point tel qu’il se conforme sans
devoir effectuer d’évaluation d’exposition maximum admissible (EMA).
Lorsque l’équipement est utilisé, il est toutefois souhaitable de laisser au
moins 20cm entre l’antenne et le corps (à l’exception des extrémités :
mains, poignets, pieds et chevilles).
308
5-7. Connecting Bluetooth
®
COROLLA_TMMMS_TMMC_U
Device registration/connection flow
1. Register the Bluetooth
®
device to be used with Entune
Audio (
2. Connect the Bluetooth
®
device to be used
(
To be used for audio
To be used for hands-free
phone
3. Start Bluetooth
®
connec-
tion (
P. 315)
3. Start Bluetooth
®
connec-
tion (
4. Check connection status
(
4. Check connection status
(
5. Use Bluetooth
®
audio
(
5. Use Bluetooth
®
phone
(
309
5-7. Connecting Bluetooth
®
5
Audi
o system
COROLLA_TMMMS_TMMC_U
To display the screen shown below, press the “SETUP” button and
select “Bluetooth
*
” on the “Setup” screen.
Select to connect the device to
be used with Entune Audio.
(
Select to register a Bluetooth
®
device to be used with Entune
Audio. (
Select
to
set
detailed
Bluetooth
®
system settings.
(
Select to delete registered devices. (
*
: Bluetooth is a registered trademark of Bluetooth SIG, Inc.
Registering and connecting from the “Bluetooth* Setup” screen
1
2
3
4
310
5-7. Connecting Bluetooth
®
COROLLA_TMMMS_TMMC_U
Turn the Bluetooth
®
connection setting of your audio player on.
Press the “AUDIO” button.
Select “
Audio”.
Select “Select Device”.
Follow the steps in “How to registering a Bluetooth
®
device” from
step
. (
Registering a Bluetooth
®
audio player for
the first time
To use the Bluetooth
®
Audio, it is necessary to register an audio
player with the system.
Once the player has been registered, it is possible to use the
Bluetooth
®
Audio.
For details about registering a Bluetooth
®
device (
1
2
3
4
5
2
311
5-7. Connecting Bluetooth
®
5
Audi
o system
COROLLA_TMMMS_TMMC_U
Turn the Bluetooth
®
connection setting of your cellular phone on.
Press the “
” button.
Select “OK” to register a phone.
Follow the steps in “How to registering a Bluetooth
®
device” from
step
. (
Registering a Bluetooth
®
phone for the first
time
To use the hands-free system, it is necessary to register a
Bluetooth
®
phone with the system.
Once the phone has been registered, it is possible to use the
hands-free system.
For details about registering a Bluetooth
®
device (
1
2
3
4
3
312
5-7. Connecting Bluetooth
®
COROLLA_TMMMS_TMMC_U
Display the “Bluetooth
*
Setup” screen. (
Select “Add”.
When this screen is displayed,
search for the device name dis-
played on this screen on the
screen of your Bluetooth
®
device.
For details about operating the
Bluetooth
®
device, see the manual
that comes with it.
To cancel the registration, select
“Cancel”.
Register the Bluetooth
®
device using your Bluetooth
®
device.
A PIN-code is not required for SSP (Secure Simple Pairing) compatible
Bluetooth
®
devices. Depending on the type of Bluetooth
®
device being
connected, a message confirming registration may be displayed on the
Bluetooth
®
device’s screen. Respond and operate the Bluetooth
®
device
according to the confirmation message.
*
: Bluetooth is a registered trademark of Bluetooth SIG, Inc.
Registering a Bluetooth
®
device
Bluetooth
®
compatible phones (HFP) and portable audio players
(AVP) can be registered simultaneously. You can register up to 5
Bluetooth
®
devices.
How to registering a Bluetooth
®
device
1
2
3
4
313
5-7. Connecting Bluetooth
®
5
Audi
o system
COROLLA_TMMMS_TMMC_U
Check that this screen is dis-
played when registration is
complete.
Select “OK” when the connection status changes from “Connect-
ing...” to “Connected”.
If an error message is displayed, follow the guidance on the screen to try
again.
Registration can be performed from screens other than the
“Bluetooth
*
Setup” screen.
■
When registering from the “Bluetooth* Audio” screen
Display the “Bluetooth
*
Audio” screen. (
Select “Select Device”.
Follow the steps in “How to registering a Bluetooth
®
device” from
step
. (
*
: Bluetooth is a registered trademark of Bluetooth SIG, Inc.
5
6
1
2
3
2
314
5-7. Connecting Bluetooth
®
COROLLA_TMMMS_TMMC_U
Display the “Bluetooth
*
Setup” screen. (
Select “Remove”.
Select the desired device.
A confirmation message will be displayed, select “Yes” to delete the
device.
Check that a confirmation screen is displayed when the operation is
complete.
*
: Bluetooth is a registered trademark of Bluetooth SIG, Inc.
Deleting a Bluetooth
®
device
1
2
3
4
5
315
5-7. Connecting Bluetooth
®
5
Audi
o system
COROLLA_TMMMS_TMMC_U
Press the “SETUP” button.
Select “Bluetooth
*
”.
Select the device to be con-
nected.
Supported profile icons will be dis-
played.
Phone
Audio player
Supported profile icons for cur-
rently connected devices will illumi-
nate.
Dimmed icons can be selected to connect to the function directly.
*
: Bluetooth is a registered trademark of Bluetooth SIG, Inc.
Connecting a Bluetooth
®
device
Up to 5 Bluetooth
®
devices (Phones (HFP) and audio players
(AVP)) can be registered.
If more than 1 Bluetooth
®
device has been registered, select
which device to connect to.
1
2
3
1
2
316
5-7. Connecting Bluetooth
®
COROLLA_TMMMS_TMMC_U
To turn auto connection mode on, set “Bluetooth
*
Power” to on.
(
When you register a phone, auto connection will be activated. Always
set it to this mode and leave the Bluetooth
®
phone in a place where a
connection can be established.
When the engine switch is turned to the “ACC” or “ON” position (vehicles
without a smart key system) or ACCESSORY or IGNITION ON mode
(vehicles with a smart key system), the system will search for a nearby cel-
lular phone you have registered.
Next, the system automatically connects with the most recent of the
phones connected to in the past. Then, the connection result is displayed.
*
: Bluetooth is a registered trademark of Bluetooth SIG, Inc.
When auto connection has failed or “Bluetooth
*
Power” is turned off,
you must connect the Bluetooth
®
device manually.
Follow the steps in “Connecting a Bluetooth
®
device” from step
.
(
*
: Bluetooth is a registered trademark of Bluetooth SIG, Inc.
Registering an additional device
Select “Select Device” on the Bluetooth
®
audio control screen.
For more information:
Selecting a registered device
Select “Select Device” on the Bluetooth
®
audio control screen.
For more information:
Auto connection
Manual connection
Connecting a Bluetooth
®
audio player
1
1
1
2
1
2
317
5-7. Connecting Bluetooth
®
5
Audi
o system
COROLLA_TMMMS_TMMC_U
■
Reconnecting a Bluetooth
®
phone
If the system cannot connect due to poor signal strength with the engine
switch in the “ACC” or “ON” position (vehicles without a smart key system) or
ACCESSORY or IGNITION ON mode (vehicles with a smart key system), the
system will automatically attempt to reconnect.
If the system is attempting to connect to a Bluetooth
®
phone and the
Bluetooth
®
phone is turned off and then back on, the system will attempt to
reconnect.
318
5-7. Connecting Bluetooth
®
COROLLA_TMMMS_TMMC_U
Display the “Bluetooth
*
Setup” screen. (
Select the device.
Select “Device Info”.
Following screen is displayed:
Device Name
Change connection method
Bluetooth
®
Address
Display your telephone num-
ber
The number may not be dis-
played depending on the
model of phone.
Compatibility profile of the
device
Restore default settings
*
: Bluetooth is a registered trademark of Bluetooth SIG, Inc.
Select “Connect Audio Player from”.
Select “Vehicle” or “Device”.
“Vehicle”: Connect Entune Audio to the portable audio player.
“Device”: Connect the portable audio player to Entune Audio
Displaying a Bluetooth
®
device details
You can confirm and change the registered device details.
Bluetooth
®
device registration status
1
2
3
4
1
2
3
4
5
6
Changing connection method
1
2
319
5-7. Connecting Bluetooth
®
5
Audi
o system
COROLLA_TMMMS_TMMC_U
Display the “Bluetooth
*
Setup” screen. (
Select “System Settings”.
The following screen is displayed:
Bluetooth
*
Power on/off
You can change Bluetooth
*
function
on/off
Bluetooth
*
Name
Change PIN-code
Bluetooth
*
Address
Display Phone Status
You can set the system to show
the status confirmation display
when connecting a telephone
Display Audio Player Status
You can set the system to show
the status confirmation display
when connecting an audio
player
Compatibility profile of the system
Restore default settings
*
: Bluetooth is a registered trademark of Bluetooth SIG, Inc.
You can change the PIN-code that is used to register your Bluetooth
®
devices in the system.
Select “Bluetooth
*
PIN”.
Input a PIN-code, and select “OK”.
*
: Bluetooth is a registered trademark of Bluetooth SIG, Inc.
Detailed Bluetooth
®
system settings
You can confirm and change the detailed Bluetooth
®
settings.
How to check and change detailed Bluetooth
®
settings
1
2
3
1
2
3
4
5
6
Editing the Bluetooth
*
PIN
7
8
1
2
320
5-8. Bluetooth
®
Audio
You can check such indicators as signal strength and battery charge
on the screen.
Connection status
Battery charge
Listening to Bluetooth
®
Audio
The Bluetooth
®
audio system enables the user to enjoy music
played on a portable player from the vehicle speakers via wire-
less communication.
When a Bluetooth
®
device cannot be connected, check the connec-
tion status on the “Bluetooth
*
Audio” screen. If the device is not con-
nected, either register or reconnect the device. (
*: Bluetooth is a registered trademark of Bluetooth SIG, Inc.
Status display
1
2
Indicators
Conditions
Connection status
Good
Not connected
Battery charge
Full
Empty
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст