Toyota Avalon (2019 year). Manual — part 30
465
8
Vehicle specifications
(fuel, oil level, etc.). . .. 466
Fuel information . . . . 475
Tire information . . . . . 478
466
8-1.Specifications
*
1
: Unladen vehicles
*
2
: Vehicles with 215/55R17 tires
Maintenance data (fuel, oil level, etc.)
Dimensions and weights
Overall length
195.9 in. (4975 mm)
Overall width
72.8 in. (1850 mm)
Overall height
*
1
56.5 in. (1435 mm)
Wheelbase
113.0 in. (2870 mm)
Tread
Front
62.6 in. (1590 mm)
63.0 in. (1600 mm)
*
2
Rear
63.2 in. (1605 mm)
63.6 in. (1615 mm)
*
2
Vehicle capacity weight
(occupants + luggage)
940 lb. (425 kg)
467
8-1. Specifications
8
Ve
hicle
spe
cifi
cations
■
Vehicle identification number
The vehicle identification number (VIN) is the legal identifier for
your vehicle. This is the primary identification number for your
Toyota. It is used in registering the ownership of your vehicle.
This number is stamped on the
top left of the instrument panel.
This number is also on the Cer-
tification Label.
Vehicle identification
468
8-1. Specifications
■
Engine number
The engine number is stamped
on the engine block as shown.
*
: Vehicles with 215/55R17 tires
Engine
Model
2GR-FKS
Type
6-cylinder V type,
4-cycle, gasoline
Bore and stroke
3.70
3.27 in.
(94.0
83.0 mm)
Displacement
210.9 cu. in. (3456 cm
3
)
Valve clearance
Automatic adjustment
Drive belt tension
Automatic adjustment
Fuel
Fuel type
Unleaded gasoline only
Octane rating
87 (Research Octane Number 91) or higher
Fuel tank capacity
(Reference)
14.5 gal. (55 L, 12.0 Imp. gal.)
*
16.0 gal. (60.6 L, 13.3 Imp. gal.)
469
8-1. Specifications
8
Ve
hicle
spe
cifi
cations
*
: The engine oil capacity is a reference quantity to be used when changing
the engine oil. Warm up and turn off the engine, wait more than 5 minutes,
and check the oil level on the dipstick.
■
Engine oil selection
“Toyota Genuine Motor Oil” is used in your Toyota vehicle. Use
Toyota approved “Toyota Genuine Motor Oil” or equivalent to sat-
isfy the following grade and viscosity.
Oil grade: ILSAC GF-5 multigrade engine oil
Recommended viscosity: SAE 0W-20
SAE 0W-20 is the best choice for
good fuel economy and good start-
ing in cold weather.
If SAE 0W-20 is not available, SAE
5W-20 oil may be used. However,
it must be replaced with SAE 0W-
20 at the next oil change.
Oil viscosity (0W-20 is explained here as an example):
• The 0W in 0W-20 indicates the characteristic of the oil which allows cold
startability. Oils with a lower value before the W allow for easier starting of
the engine in cold weather.
• The 20 in 0W-20 indicates the viscosity characteristic of the oil when the
oil is at high temperature. An oil with a higher viscosity (one with a higher
value) may be better suited if the vehicle is operated at high speeds, or
under extreme load conditions.
Lubrication system
Oil capacity
(Drain and refill ―
reference
*
)
With filter
Without filter
5.7 qt. (5.4 L, 4.8 Imp. qt.)
5.6 qt. (5.3 L, 4.7 Imp. qt.)
Outside temperature
470
8-1. Specifications
How to read oil container label:
The International Lubricant
Specification Advisory Commit-
tee (ILSAC) Certification Mark
is added to some oil containers
to help you select the oil you
should use.
Cooling system
Capacity
(Reference)
9.1 qt. (8.6 L, 7.6 Imp. qt.)
Coolant type
Use either of the following:
• “Toyota Super Long Life Coolant”
• Similar high-quality ethylene glycol-based
non-silicate, non-amine, non-nitrite, and
non-borate coolant with long-life hybrid
organic acid technology
Do not use plain water alone.
Ignition system
Spark plug
Make
DENSO FK20HBR8
Gap
0.031 in. (0.8 mm)
NOTICE
■
Iridium-tipped spark plugs
Use only iridium-tipped spark plugs. Do not adjust spark plug gap.
471
8-1. Specifications
8
Ve
hicle
spe
cifi
cations
*
: The fluid capacity is a reference quantity.
If replacement is necessary, contact your Toyota dealer.
Electrical system
Battery
Specific voltage reading at
68
F (20C):
12.3 V or higher
If the voltage is lower than the standard
value, charge the battery.
(When checking the voltage, after turning
the engine switch off, wait for 30 seconds
with the high beam headlights illuminated,
then turn the high beam headlights off and
check the voltage.)
Charging rates
5 A max.
Automatic transaxle
Fluid capacity
*
7.9 qt. (7.5 L, 6.6 Imp. qt.)
Fluid type
Toyota Genuine ATF WS
NOTICE
■
Transmission fluid type
Using transmission fluid other than “Toyota Genuine ATF WS” may cause
deterioration in shift quality, locking up of the transmission accompanied by
vibration and, ultimately, damage to the vehicle’s transmission.
472
8-1. Specifications
*
: Minimum pedal clearance when depressed with a force of 67 lbf (300 N, 31
kgf) while the engine is running.
17-inch tires
Brakes
Pedal clearance
*
3.2 in. (81 mm)
Pedal free play
0.04
0.24 in. (1 6 mm)
Brake pad wear limit
0.04 in. (1.0 mm)
Fluid type
SAE J1703 or FMVSS No.116 DOT 3
SAE J1704 or FMVSS No.116 DOT 4
Steering
Free play
Less than 1.2 in. (30 mm)
Tires and wheels
Tire size
215/55R17 94V, T155/70D17 110M
Tire inflation pressure
(Recommended cold tire
inflation pressure)
Driving under normal conditions
Front:
35 psi (240 kPa, 2.4 kgf/cm
2
or bar)
Rear:
35 psi (240 kPa, 2.4 kgf/cm
2
or bar)
Spare:
60 psi (420 kPa, 4.2 kgf/cm
2
or bar)
Driving at high speeds (above 100 mph
[160 km/h]) (in countries where such
speeds are permitted by law)
Add 5 psi (30 kPa, 0.3 kgf/cm
2
or bar) to
the front tires and rear tires. Never
exceed the maximum cold tire inflation
pressure indicated on the tire sidewall.
Wheel size
17
7 1/2 J, 17 4 T (compact spare)
Wheel nut torque
76 ft•lbf (103 N•m, 10.5 kgf•m)
473
8-1. Specifications
8
Ve
hicle
spe
cifi
cations
18-inch tires
19-inch tires
Tire size
235/45R18 94V, T155/70D17 110M
Tire inflation pressure
(Recommended cold tire
inflation pressure)
Driving under normal conditions
Front:
35 psi (240 kPa, 2.4 kgf/cm
2
or bar)
Rear:
35 psi (240 kPa, 2.4 kgf/cm
2
or bar)
Spare:
60 psi (420 kPa, 4.2 kgf/cm
2
or bar)
Driving at high speeds (above 100 mph
[160 km/h]) (in countries where such
speeds are permitted by law)
Add 5 psi (30 kPa, 0.3 kgf/cm
2
or bar) to
the front tires and rear tires. Never
exceed the maximum cold tire inflation
pressure indicated on the tire sidewall.
Wheel size
18
8 J, 17 4 T (compact spare)
Wheel nut torque
76 ft•lbf (103 N•m, 10.5 kgf•m)
Tire size
235/40R19 92V, T155/70D17 110M
Tire inflation pressure
(Recommended cold tire
inflation pressure)
Driving under normal conditions
Front:
35 psi (240 kPa, 2.4 kgf/cm
2
or bar)
Rear:
35 psi (240 kPa, 2.4 kgf/cm
2
or bar)
Spare:
60 psi (420 kPa, 4.2 kgf/cm
2
or bar)
Driving at high speeds (above 100 mph
[160 km/h]) (in countries where such
speeds are permitted by law)
Add 5 psi (30 kPa, 0.3 kgf/cm
2
or bar) to
the front tires and rear tires. Never
exceed the maximum cold tire inflation
pressure indicated on the tire sidewall.
Wheel size
19
8 J, 17 4 T (compact spare)
Wheel nut torque
76 ft•lbf (103 N•m, 10.5 kgf•m)
474
8-1. Specifications
*
: Light bulbs not listed in this table are LED bulbs.
Light bulbs
*
Light bulbs
Bulb No.
W
Type
Interior
Door courtesy lights
168
5
A
Vanity lights
7065
1.4
B
Trunk light
5
A
A: Wedge base bulbs
B: Double end bulbs
475
8-1. Specifications
8
Ve
hicle
spe
cifi
cations
■
Gasoline quality
In very few cases, driveability problems may be caused by the brand of gaso-
line you are using. If driveability problems persist, try changing the brand of
gasoline. If this does not correct the problem, consult your Toyota dealer.
■
Recommendation of the use of gasoline containing detergent additives
●
Toyota recommends the use of gasoline that contains detergent additives to
avoid the build-up of engine deposits.
●
All gasoline sold in the U.S.A. contains minimum detergent additives to
clean and/or keep clean intake systems, per EPA’s lowest additives concen-
tration program.
●
Toyota strongly recommends the use of Top Tier Detergent Gasoline. For
more information on Top Tier Detergent Gasoline and a list of marketers,
please go to the official website www.toptiergas.com.
Fuel information
You must only use unleaded gasoline.
Select octane rating 87 (Research Octane Number 91) or higher.
Use of unleaded gasoline with an octane rating lower than 87
may result in engine knocking. Persistent knocking can lead to
engine damage.
At minimum, the gasoline you use should meet the specifications of
ASTM D4814 in the U.S.A..
476
8-1. Specifications
■
Recommendation of the use of low emissions gasoline
Gasolines containing oxygenates such as ethers and ethanol, as well as
reformulated gasolines, are available in some cities. These fuels are typically
acceptable for use, providing they meet other fuel requirements.
Toyota recommends these fuels, since the formulations allow for reduced
vehicle emissions.
■
Non-recommendation of the use of blended gasoline
●
If you use gasohol in your vehicle, be sure that it has an octane rating no
lower than 87.
●
Toyota does not recommend the use of gasoline containing methanol.
■
Non-recommendation of the use of gasoline containing MMT
Some gasoline contains an octane enhancing additive called MMT (Methylcy-
clopentadienyl Manganese Tricarbonyl).
Toyota does not recommend the use of gasoline that contains MMT. If fuel
containing MMT is used, your emission control system may be adversely
affected.
The malfunction indicator lamp on the instrument cluster may come on. If this
happens, contact your Toyota dealer for service.
■
If your engine knocks
●
Consult your Toyota dealer.
●
You may occasionally notice light knocking for a short time while accelerat-
ing or driving uphill. This is normal and there is no need for concern.
●
Use only gasoline containing up to 15%
ethanol.
DO NOT use any flex-fuel or gasoline
that could contain more than 15% etha-
nol, including from any pump labeled
E30, E50, E85 (which are only some
examples of fuel containing more than
15% ethanol).
DO NOT use gasoline contain-
ing more than 15% ethanol.
(30% ethanol)
(50% ethanol)
(85% ethanol)
477
8-1. Specifications
8
Ve
hicle
spe
cifi
cations
NOTICE
■
Notice on fuel quality
●
Do not use improper fuels. If improper fuels are used, the engine will be
damaged.
●
Do not use leaded gasoline.
Leaded gasoline can cause damage to your vehicle’s three-way catalytic
converters causing the emission control system to malfunction.
●
Do not use gasohol other than the type previously stated.
Other gasohol may cause fuel system damage or vehicle performance
problems.
●
Using unleaded gasoline with an octane number or rating lower than the
level previously stated will cause persistent heavy knocking.
At worst, this will lead to engine damage.
■
Fuel-related poor driveability
If poor driveability (poor hot starting, vaporization, engine knocking, etc.) is
encountered after using a different type of fuel, discontinue the use of that
type of fuel.
■
When refueling with gasohol
Take care not to spill gasohol. It can damage your vehicle’s paint.
478
8-1. Specifications
Full-size tire
Compact spare tire
Tire information
Typical tire symbols
479
8-1. Specifications
8
Ve
hicle
spe
cifi
cations
Tire size (
P. 481)
Summer tires or all season tires (
An all season tire has “M+S” on the sidewall. A tire not marked “M+S”
is a summer tire.
TUBELESS or TUBE TYPE
A tubeless tire does not have a tube and air is directly put into the tire.
A tube type tire has a tube inside the tire and the tube maintains the air
pressure.
Radial tires or bias-ply tires
A radial tire has “RADIAL” on the sidewall. A tire not marked “RADIAL”
is a bias-ply tire.
DOT and Tire Identification Number (TIN) (
P. 480)
Location of treadwear indicators (
Uniform tire quality grading
For details, see “Uniform Tire Quality Grading” that follows.
Maximum cold tire inflation pressure (
This means the pressure to which a tire may be inflated.
Load limit at maximum cold tire inflation pressure (
Tire ply composition and materials
Plies are layers of rubber-coated parallel cords. Cords are the strands
which form the plies in a tire.
“TEMPORARY USE ONLY”
A compact spare tire is identified by the phrase “TEMPORARY USE
ONLY” molded on its sidewall. This tire is designed for temporary
emergency use only.
1
2
3
4
5
6
7
8
9
10
11
480
8-1. Specifications
DOT symbol
*
Tire Identification Number (TIN)
Tire manufacturer’s identification mark
Tire size code
Manufacturer’s optional tire type code (3 or 4 letters)
Manufacturing week
Manufacturing year
Manufacturer’s code
*
: The DOT symbol certifies that the tire conforms to applicable Federal
Motor Vehicle Safety Standards.
Typical DOT and Tire Identification Number (TIN)
Type A
Type B
1
2
3
4
5
6
7
8
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст