Toyota Avalon (2019 year). Manual — part 6
81
2. Instrument cluster
2
Instrument cluster
*
1
: These lights turn on when the engine switch is turned to IGNITION ON
mode to indicate that a system check is being performed. They will turn off
after the engine is started, or after a few seconds. There may be a mal-
function in a system if a light does not come on, or turn off. Have the vehi-
cle inspected by your Toyota dealer.
*
2
: This light illuminates on the multi-information display.
*
3
: This light does not turn on when the system is disabled.
*
4
: This light turns on when the system is off.
*
5
: This light flashes to indicate that the system is operating.
*
6
: These indicators will illuminate in the following situations to indicate that
the system initial check is being performed:
• When the BSM function or RCTA function is enabled and the engine
switch is turned to IGNITION ON mode.
• When the engine switch is in IGNITION ON mode and the BSM function
is enabled.
• When the engine switch is in IGNITION ON mode and the RCTA func-
tion is enabled. (At this time, a buzzer will also sound.)
The indicators will turn off after a few seconds. If the indicators do not
illuminate or turn off, or if a buzzer does not sound when the RCTA func-
tion is enabled, the system may be malfunctioning. Have the vehicle
inspected by your Toyota dealer.
*
7
: This light illuminates on the outside rear view mirrors.
*
8
: This light illuminates on the center panel.
*
9
: When the outside temperature is approximately 37°F (3°C) or lower, this
indicator will flash for approximately 10 seconds, then stay on.
WARNING
■
If a safety system warning light does not come on
Should a safety system light such as the ABS and SRS warning lights not
come on when you start the engine, this could mean that these systems are
not available to help protect you in an accident, which could result in death
or serious injury. Have the vehicle inspected by your Toyota dealer immedi-
ately if this occurs.
82
2. Instrument cluster
The units used on the meters may differ depending on the target region.
Tachometer
Displays the engine speed in revolutions per minute
Shift position (
Outside temperature
Displays the outside temperature within the range of -40°F (-40°C) to
122°F (50°C). Low outside temperature indicator comes on when the
ambient temperature is 37°F (3°C) or lower.
Multi-information display
Presents the driver with a variety of vehicle data (
Displays warning messages in case of a malfunction (
Speedometer
Fuel gauge
Odometer and trip meter
P. 97)
Engine coolant temperature gauge
Displays the engine coolant temperature
Gauges and meters
1
2
3
4
5
6
7
8
83
2. Instrument cluster
2
Instrument cluster
The brightness of the instrument panel lights can be adjusted.
The brightness of some of the interior lights will be changed when the
brightness of the instrument panel lights is adjusted. (
Darker
Brighter
• The brightness of the instrument
panel lights can be adjusted
individually for day mode and
night mode
*
.
• If the brightness is adjusted
when the surroundings are
bright and the tail lights are on
(day mode brightness adjust-
ment), the brightness level of
night mode will be adjusted at
the same time.
*
: Day mode and night mode:
Instrument panel light control
1
2
84
2. Instrument cluster
■
The meters and display illuminate when
The engine switch is in IGNITION ON mode.
■
Brightness of the meters (day mode and night mode)
●
The brightness of the meters is changed between day mode and night
mode.
• Day mode: When the tail lights are off or when the tail lights are on but
the surrounding area is bright
• Night mode: When the tail lights are on and the surrounding area is dark
●
When in night mode, the brightness will be reduced slightly unless the
meters are set to the maximum brightness level.
■
Outside temperature display
In the following situations, the correct outside temperature may not be dis-
played, or the display may take longer than normal to change:
●
When stopped, or driving at low speeds (less than 16 mph [25 km/h])
●
When the outside temperature has changed suddenly (at the entrance/exit
of a garage, tunnel, etc.)
●
When “
” or “E” is displayed, the system may be malfunctioning.
Take your vehicle to your Toyota dealer.
NOTICE
■
To prevent damage to the engine and its components
●
Do not let the indicator needle of the tachometer enter the red zone, which
indicates the maximum engine speed.
●
The engine may be overheating if the engine coolant temperature gauge is
in the red zone (H). In this case, immediately stop the vehicle in a safe
place, and check the engine after it has cooled completely. (
85
2. Instrument cluster
2
Instrument cluster
The multi-information display presents the driver with a variety of driv-
ing-related data, such as the current outside temperature. The multi-
information display can also be used to change the display settings
and other settings.
Indicators (
Driving assist system status display area
Displays the operational status of the following systems:
• Dynamic radar cruise control with full-speed range (
• LDA (Lane Departure Alert with steering control) (
Speed limit display (vehicles with a navigation system) (U.S.A.
only)
Speedometer
The speedometer display can be enabled/disabled in
on the multi-
information display. (
When
is selected, the speedometer may be displayed in the content
display area.
Content display area
A variety of information can be displayed by selecting a menu icon. Addi-
tionally, warning or suggestion/advice pop-up displays will be displayed in
some situations.
• Menu icon content (
• Suggestion function (
• Warning message (
Multi-information display
Summary of functions
1
2
3
4
5
86
2. Instrument cluster
Odometer/trip meter (
Shift position (
Outside temperature (
P. 82)
Menu icons (
“ODO/TRIP” switch (
Meter control switches (
◆
Using the content display area
The content display area is operated using the meter control
switches.
Scroll screens
*
, change the
displayed content
*
and move
the cursor
Press: Enter/Set
Press and hold: Reset/Dis-
play the next screen
Return to the previous
screen
Pressing and holding the switch will display the first screen of the
selected menu icon.
*
: When the screen can be scrolled or different content can be displayed,
a mark, such as an arrow, will be displayed to suggest which switch to
operate.
◆
Using the odometer/trip meter
Items in this area are operated using the “ODO/TRIP” switch.
Press: Change displayed item
Each time the switch is pressed,
the displayed item will be
changed.
Press and hold: Reset
Display the desired trip meter
and press and hold the switch to
reset the trip meter.
Using the multi-information display
6
7
8
9
10
11
1
2
3
87
2. Instrument cluster
2
Instrument cluster
Select a menu icon to display its content.
Driving information (
Select to display the following:
• Speedometer/driving range
• Fuel consumption
• Eco Driving Indicator/driving range
Driving assist system information
Select to perform the following:
Display the operational status of the following systems:
• Dynamic radar cruise control with full-speed range (
• LDA (Lane Departure Alert with steering control) (
Display the following navigation system-linked information (if equipped):
• Route guidance
• Compass display (heading-up display)
Audio system-linked display
Select to enable selection of an audio source or track on the multi-infor-
mation display using the meter control switches.
Vehicle information
Select to perform the following:
Display the following information:
• Tire inflation pressure (
Enable/Disable the following systems:
• Parking assist (Intuitive parking assist) (if equipped) (
• BSM (Blind Spot Monitor) function (
• RCTA (Rear Cross Traffic Alert) function (
These functions can also be enabled/disabled on
.
Settings display (
Select to change the meter display settings and other settings.
Warning message display (
Select to display warning messages and measures to be taken if a mal-
function is detected.
Menu icons
88
2. Instrument cluster
■
Speedometer/driving range
• Speedometer
• Driving range
Displays the driving range with remaining fuel.
When only a small amount of fuel is added to the tank, the display may
not be updated.
When refueling, turn the engine switch off. If the vehicle is refueled with-
out turning the engine switch off, the display may not be updated.
This distance is computed based on your average fuel consumption. As
a result, the actual distance that can be driven may differ from that dis-
played.
■
Fuel consumption
Current fuel consumption
Displays the instantaneous cur-
rent fuel consumption.
Average fuel economy (after
start)
Displays the average fuel con-
sumption since engine start.
*
1
Driving range
Displays the driving range with remaining fuel.
*
2, 3
Driving information (
)
1
2
3
89
2. Instrument cluster
2
Instrument cluster
Gadget
*
4
The following items can be displayed by changing the settings for gad-
get content and fuel economy type on
. (
Average fuel economy
Displayed item (listed below) can be changed on the fuel economy type
screen of
. (
● Total (after reset)
Displays the average fuel consumption since the display was reset.
*
1, 5
● Tank (after refuel)
Displays the average fuel consumption since the vehicle was refu-
eled.
*
1, 2
4
Displayable item
Content
Gadget
content
Fuel economy
type
Average
vehicle
speed
Trip
(after start)
Displays the average vehicle speed since
engine start.
Total
(after reset)
Displays the average vehicle speed since the
display was reset.
*
5
Distance
Trip
(after start)
Displays the distance driven since vehicle
start.
Total
(after reset)
Displays the distance driven since the display
was reset.
*
5
Elapsed
time
Trip
(after start)
Displays the elapsed time since engine start.
Total
(after reset)
Displays the elapsed time since the display
was reset.
*
5
5
90
2. Instrument cluster
*
1
: Use the displayed fuel consumption as a reference only.
*
2
: When only a small amount of fuel is added to the tank, the display may
not be updated.
When refueling, turn the engine switch off. If the vehicle is refueled with-
out turning the engine switch off, the display may not be updated.
*
3
: This distance is computed based on your average fuel consumption. As
a result, the actual distance that can be driven may differ from that dis-
played.
*
4
: The default setting is no display.
*
5
: This display can be reset by pressing and holding
while it is dis-
played.
■
Eco Driving Indicator/driving range
• Eco Driving Indicator
• Driving range
Displays the driving range with remaining fuel.
When only a small amount of fuel is added to the tank, the display may
not be updated.
When refueling, turn the engine switch off. If the vehicle is refueled with-
out turning the engine switch off, the display may not be updated.
This distance is computed based on your average fuel consumption. As
a result, the actual distance that can be driven may differ from that dis-
played.
91
2. Instrument cluster
2
Instrument cluster
◆
Changing settings
Use the meter control switches on the steering wheel to change
settings.
Press
or
to select
.
Operate the switches to select a desired item.
Press or press and hold
.
The available settings will differ depending on if
is pressed or
pressed and held. Follow the instructions on the display.
◆
Setting items
■
LDA (Lane Departure Alert with steering control) (
P. 228)
Press and hold
to change the settings of the following items:
Settings display (
)
1
2
3
Item
Settings
Details
Steering assist
On
Select to enable/disable steering
wheel assistance.
Off
Alert sensitivity
(High)
Select to set the warning sensi-
tivity.
(Normal)
Sway warning
On
Select to enable/disable the vehi-
cle sway warning.
Off
Sway sensitivity
(High)
Select to set the vehicle sway
warning sensitivity.
(Medium)
(Low)
92
2. Instrument cluster
■
PCS (Pre-Collision System) (
Press
to enable/disable the pre-collision system.
Press and hold
to change the settings of the following item:
■
BSM (Blind Spot Monitor) (
Press
to enable/disable the Blind Spot Monitor function.
Press and hold
to change the settings of the following item:
Item
Settings
Details
PCS
On
Select to enable/disable the pre-
collision system.
Off
Item
Settings
Details
Warning sensitivity
(Warning timing)
(Far)
Select to change the warning
timing.
(Middle)
(Near)
Item
Settings
Details
BSM
On
Select to enable/disable the
Blind Spot Monitor function.
Off
Item
Settings
Details
Outside rear view
mirror
indicator
brightness
(Bright)
Select to change the brightness
of the outside rear view mirror
indicators.
(Dim)
93
2. Instrument cluster
2
Instrument cluster
■
RCTA (Rear Cross Traffic Alert) (
Press
to enable/disable the Rear Cross Traffic Alert function.
Press and hold
to change the settings of the following item:
■
ICS (Intelligent Clearance Sonar) (if equipped) (
Press
to enable/disable the Intelligent Clearance Sonar.
■
Parking assist (Intuitive parking assist) (if equipped)
(
P. 266)
Press
to enable/disable the Intuitive parking assist.
Press and hold
to change the settings of the following item:
Item
Settings
Details
RCTA
On
Select to enable/disable the Rear
Cross Traffic Alert function.
Off
Item
Settings
Details
RCTA buzzer vol-
ume
(Low)
Select to change the volume of
the RCTA buzzer.
(Medium)
(Loud)
Item
Settings
Details
ICS
On
Select to enable/disable the
Intelligent Clearance Sonar sys-
tem.
Off
Item
Settings
Details
Intuitive
parking
assist
On
Select to enable/disable the intui-
tive parking assist.
Off
Item
Settings
Details
Volume
(Low)
Select to change the volume of
the intuitive parking assist
buzzer.
(Medium)
(Loud)
94
2. Instrument cluster
■
HUD (Head-up display) (if equipped) (
Press
to enable/disable the head-up display.
Press and hold
to change the settings of the following items:
Item
Settings
Details
HUD
On
Select to enable/disable the
head-up display.
Off
Item
Settings
Details
HUD Brightness/Position
Select to adjust the brightness/
position of the head-up display.
• Press the
/
switch to
adjust the display brightness.
• Press the
/
switch to
adjust the display position.
HUD Driving
support
Tachometer
settings
Select to change the display
between the following:
• Eco Driving Indicator
• Tachometer
• No content
Navigation
system
Select to enable/disable head-up
display content.
Driving Assist
Compass
Rotation
Select to adjust the angle of the
head-up display.
Press the
/
switch to
adjust the display angle.
95
2. Instrument cluster
2
Instrument cluster
■
Vehicle settings
Press and hold
to change the settings of the following items:
Item
Settings
Details
TPWS (Tire pressure warning system) (
Set pressure (tire pressure warning sys-
tem initialization)
Select to initialize the tire pres-
sure warning system. To per-
form initialization, press and hold
the
switch.
Before performing initialization,
make sure to adjust the inflation
pressure of each tire to the spec-
ified level. (
Change wheel (register tire pressure
warning system sensor ID codes)
Select to register the ID codes of
the tire pressure sensors to the
tire pressure warning system. To
register the ID codes, press and
hold the
switch.
(
Scheduled maintenance display
Maintenance data reset
Select to reset the message indi-
cating maintenance is required,
after the required maintenance is
performed. (
96
2. Instrument cluster
■
Meter settings
Press and hold
to change the settings of the following items:
*
1
: Selecting this item will only change the gadget.
*
2
: Selecting this item will turn the display of the gadget off.
Item
Settings
Details
Language
Select to change the language
displayed.
Units
Select to change the units of
measure displayed.
(Eco Driving
Indicator Light)
On
Select to enable/disable the Eco
Driving Indicator Light. (
Off
Speedometer
On
Select to enable/disable the
speedometer display.
Off
Gadget content
Off
No display
Average vehicle
speed
Select to turn the display of a
gadget.
Distance
Elapsed time
Fuel economy type
Trip (after start)
*
1
Select to change the average
fuel consumption display and an
item to be displayed as gadget.
Total (after reset)
Tank
(after refuel)
*
2
Multi-information display off
Select to turn the multi-informa-
tion display off.
To turn the multi-information dis-
play on again, press any direc-
tion switch (
/
/
/
).
Pop-up display
Intersection guid-
ance (if equipped)
Select to enable/disable the pop-
up display.
Incoming calls
Brightness adjust-
ment
Default setting
Select to reset the meter display
settings to the default setting.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст