Toyota Tundra (2019 year). Manual — part 7
97
2
Instrument cluster
Pressing the button switches
between odometer and trip meter.
■
Odometer
Displays the total distance the vehicle has been driven.
■
Trip meter A*/trip meter B*
Displays the distance the vehicle has been driven since the meter
was last reset. Trip meters A and B can be used to record and dis-
play different distances independently.
*
: Press and hold the display change button to reset.
The brightness of the instrument panel lights can be adjusted.
Pressing the button will adjust
brightness of the instrument panel
light.
The brightness of the instrument
panel lights can be adjusted by
pressing the button.
Short press: 1 step change of
brightness level.
Long press: continues change of
brightness level until released.
Changing the odometer/trip meter display
Instrument panel light control
98
■
The multi-information display illuminate when
The engine switch is in the “ON” position.
■
The brightness of the instrument panel lights
When the tail lights are turned on, the display’s brightness will be reduced
slightly unless the meter brightness level adjustment is set to the brightest
setting.
■
Outside temperature display
●
In the following situations, the correct outside temperature may not be dis-
played, or the display may take longer than normal to change.
• When stopped, or driving at low speeds (less than 12 mph [20 km/h])
• When the outside temperature has changed suddenly (at the entrance/
exit of a garage, tunnel, etc.)
●
When “--” or “E” is displayed, the system may be malfunctioning.
Take your vehicle to your Toyota dealer.
■
Liquid crystal display
Small spots or light spots may appear on the display. This phenomenon is
characteristic of liquid crystal displays, and there is no problem continuing to
use the display.
WARNING
■
The information display at low temperatures
Allow the interior of the vehicle to warm up before using the liquid crystal
information display. At extremely low temperatures, the information display
monitor may respond slowly, and display changes may be delayed.
For example, there is a lag between the driver’s shifting and the new gear
number appearing on the display. This lag could cause the driver to down-
shift again, causing rapid and excessive engine braking and possibly an
accident resulting in personal death or injury.
99
2
Instrument cluster
NOTICE
■
To prevent damage to the engine and its components
●
Do not let the indicator needle of the tachometer enter the red zone, which
indicates the maximum engine speed.
●
The engine may be overheating if the engine coolant temperature gauge is
in the red zone (H). In this case, immediately stop the vehicle in a safe
place, and check the engine after it has cooled completely. (
■
Voltmeter
When the voltmeter indicates 19 V or higher or 9 V or lower while the engine
is running, there may be a battery or charging system malfunction. Have the
vehicle inspected at your Toyota dealer.
■
Engine oil pressure gauge
When the value of the engine oil pressure gauge drops while the engine is
running, stop the vehicle in a safe place immediately and check the amount
of engine oil. (
When the oil pressure drops even though the engine oil amount has not
decreased, or if the oil pressure does not increase when engine oil is
added, contact your Toyota dealer, as there may be a problem with the lubri-
cation system.
100
Multi-information display
The multi-information display presents the driver with a variety of vehi-
cle data.
● Menu icons
Displays the following informa-
tion when an icon is selected.
Some of the information may be
displayed
automatically
depending on the situation.
Drive information
Select to display various drive data. (
Navigation system-linked display
*
Select to display the following navigation system-linked information.
• Route guidance
• Compass display (north-up display/heading-up display)
Audio system-linked display
Select to enable selection of an audio source or track on the meter
using the meter control switches.
Vehicle information
Select to display the operational status of the following systems:
• LDA (Lane Departure Alert)
*
(
• Dynamic radar cruise control
*
(
• Tire inflation pressure (
• Trailer brake controller
*
(
Display contents
101
2
Instrument cluster
Warning message display
Select to display warning messages and measures to be taken if a
malfunction is detected. (
Settings display
Select to change the meter display settings. (
*
: If equipped
■
Operating the meter control switches
Select an item/change pages
Press: Enters/Sets
Press and hold: Resets
Switch menu/Displays the
top screen
Returns to the previous
screen
● Total Average
*
/Tank Average/Trip Average
Displays the average fuel consumption since the function was
reset, the vehicle was refueled, or the engine was started, respec-
tively
Use the displayed average fuel consumption as a reference.
● Range
Displays the estimated maximum distance that can be driven with
the quantity of fuel remaining, the distance driven after the engine
was started or the distance since the function was reset, respec-
tively.
• This distance is computed based on your average fuel consumption. As
a result, the actual distance that can be driven may differ from that dis-
played.
• When only a small amount of fuel is added to the tank, the display may
not be updated.
When refueling, turn the engine switch off. If the vehicle is refueled with-
out turning the engine switch off, the display may not be updated.
1
2
3
4
Drive information
102
● Current
Displays the current rate of fuel consumption
● Average Speed
*
/Trip Average Speed
Displays the average since engine was started or the average since
the function was reset, respectively
● Total Time
*
/Trip Time
Displays the engine was started or the elapsed time since the func-
tion was reset, respectively
● Trip distance
Displays the distance since the engine was started
● Digital speedometer
● Display off
A blank screen is displayed
*
: Resetting procedures:
• Select a function to be reset using the meter control switch and then
press and hold the center button to reset.
• If there is more than one function that can be reset, check boxes will be
displayed next to the functions.
The settings of the following items can be changed, refer to P. 623.
For functions that can be enabled or disabled, the function switches
between on and off each time is
pressed.
● LDA (Lane Departure Alert)
*
1
• LDA Sensitivity
Select to set up the LDA (Lane Departure Alert) sensitivity.
• Sway warning
Select to enable/disable the Sway warning function.
• Sway warning sensitivity
Select to set up the sway warning sensitivity.
● PCS (Pre-Collision System)
*
1
• PCS
Select to enable/disable the PCS (Pre-Collision System) function.
• Sensitivity
Select to set up the PCS (Pre-Collision System) sensitivity.
Settings display
103
2
Instrument cluster
● BSM (Blind Spot Monitor)
*
1
Select to enable/disable the Blind Spot Monitor function.
● RCTA (Rear Cross Traffic Alert)
*
1
Select to enable/disable the Rear Cross Traffic Alert function.
● Vehicle Settings
• BSM Brightness
*
1
(
Select to set up the BSM (Blind Spot Monitor) outside rear view mirror
indicators brightness.
• RCTA volume
*
1
(
Select to set up the RCTA (Rear Cross Traffic Alert) warning buzzer vol-
ume.
• TBC Trailer Type
*
1
(
Select to set up the trailer brake type.
• Maintenance reset
*
2
(
Select to reset the message after the required maintenance is per-
formed.
104
● Meter setting
• Language
Select to change the language on the display.
• Units
Select to change the unit of measure for fuel consumption and tempera-
ture.
• Switch settings
You can register 1 screen as the top screen. To register, press and hold
while the desired screen is displayed.
There are also screens that cannot be setup as the Top Screen.
• Drive information 1 and 2
Select to select up to 2 items that will be displayed on a Drive informa-
tion screen, up to 2 Drive information screens can be set.
• Pop-up display
Select to set the following pop-up displays, which may appear in some
situations, on/off.
• Route guidance display of the navigation system-linked system (if
equipped)
• Incoming call display of the hands-free phone system
• Instrument panel brightness adjustment display
• Accent color
Select to change the accent colors on the screen, such as the menu
icon color.
• Default settings
Registered or changed meter settings will be deleted or returned to their
default setting.
*
1
: If equipped
*
2
: For vehicles sold in the U.S.A.
105
2
Instrument cluster
■
Setting items
●
“Vehicle Settings” and “Meter Settings” setting items are not selectable
during driving and cannot be operated.
Also, the settings screen is temporarily canceled in the following situations.
• When a warning message appears.
• When the vehicle begins to move.
●
Settings for functions not equipped to the vehicle are not displayed.
●
When a function is turned off, the related settings for that function are not
selectable.
■
Pop-up display
In some situations, such as when a switch operation is performed, a pop-up
display will be temporarily displayed on the multi-information display.
■
When disconnecting and reconnecting battery terminals
The drive information will be reset.
■
Trip summary display
When the engine switch is turned off, each of the following will be displayed
on the multi-information display, and will clear after approximately 30 sec-
onds.
●
Distance traveled
●
Average fuel consumption
●
Driving range
■
Tire inflation pressure
●
It may take a few minutes to display the tire inflation pressure after the
engine switch is turned to the “ON” position. It may also take a few minutes
to display the tire inflation pressure after inflation pressure has been
adjusted.
●
“---” may be displayed if the tire position information cannot be determined
due to unfavorable radio wave conditions.
●
Tire inflation pressure changes with temperature. The displayed values may
also be different from the values measured using a tire pressure gauge.
■
Liquid crystal display
Small spots or light spots may appear on the display. This phenomenon is
characteristic of liquid crystal displays, and there is no problem continuing to
use the display.
106
WARNING
■
Caution for use while driving
●
When operating the multi-information display while driving, pay extra
attention to the safety of the area around the vehicle.
●
Do not look continuously at the multi-information display while driving as
you may fail to see pedestrians, objects on the road, etc. ahead of the
vehicle.
■
Cautions during setting up the display
As the engine needs to be running during setting up the display, ensure that
the vehicle is parked in a place with adequate ventilation. In a closed area
such as a garage, exhaust gases including harmful carbon monoxide (CO)
may collect and enter the vehicle. This may lead to death or a serious
health hazard.
NOTICE
■
During setting up the display
To prevent battery discharge, ensure that the engine is running while setting
up the display features.
107
2
Instrument cluster
Fuel consumption information
Entune Audio
Press the “TRUCK” button.
Entune Premium Audio and Entune Audio Plus
Press the “APPS” button, and then select “Eco” on the screen.
■
Trip information
If the “Past Record” screen is displayed, select “Trip Information”.
Resetting the consumption
data
Average vehicle speed since
the engine was started
Elapsed time since the
engine was started
Fuel consumption in the past
15 minutes
Cruising range (
Current fuel consumption
Average fuel consumption for the past 15 minutes is divided by
color into past averages and averages attained since the engine
switch was last turned to the “ON” position. Use the displayed aver-
age fuel consumption as a reference.
These images are examples only.
: If equipped
The fuel consumption information can be displayed on Entune
Audio, Entune Premium Audio and Entune Audio Plus screen.
Display the trip information or past record screen
Fuel consumption
1
2
3
4
5
6
108
■
Past record
If the “Trip Information” screen is displayed, select “Past Record”.
Resetting the past record
data
Best recorded fuel consump-
tion
Average fuel consumption (if
equipped)
Previous fuel consumption
record
Current fuel economy
Update the average fuel consumption data
The average fuel consumption history is divided by color into past
averages and the average fuel consumption since the last updated.
Use the displayed average fuel consumption as a reference.
These images are examples only.
■
Resetting the data
The fuel consumption data can be deleted by selecting “Clear”.
■
Updating the past record data
Update the average fuel consumption by selecting “Update” to measure the
current fuel consumption again.
■
Cruising range
Displays the estimated maximum distance that can be driven with the quan-
tity of fuel remaining.
This distance is computed based on your average fuel consumption. As a
result, the actual distance that can be driven may differ from that displayed.
1
2
3
4
5
6
109
3
Operation of
each component
3-1. Key information
Keys . . . . . . . . .. 110
3-2. Opening, closing and
locking the doors
Side doors . . . . . . . 114
Tailgate . . . . . . . . 118
3-3. Adjusting the seats
Front seats . . . . . . 123
Rear seats. . . . . . . 126
Driving position memory
(driver’s seat) . . . . .. 128
Head restraints. . . . .. 132
3-4. Adjusting the steering
wheel and mirrors
Steering wheel . . . . .. 136
Inside rear view mirror. ... 139
Outside rear view
mirrors. . . . . . . . 142
3-5. Opening, closing the
windows and moon roof
Power windows . . . . . 147
Back window . . . . . . 150
Power back window . . .. 151
Moon roof. . . . . . .. 154
110
Keys
The following keys are provided with the vehicle.
Vehicles without wireless remote control
Keys
Key number plate
Vehicles with wireless remote control
Keys
Operating the wireless remote con-
trol function
Key number plate
Locks all the doors (
Unlocks all the doors (
Pressing the button unlocks the
driver’s door. Pressing the button
again within 3 seconds unlocks the
other doors.
Sounds the alarm (press and
hold) (
The keys
1
2
1
2
Wireless remote control (if equipped)
1
2
3
111
3-1. Key information
3
Opera
■
If you lose your keys
New genuine key can be made by your Toyota dealer using the other key and
the key number stamped on your key number plate.
Keep the plate in a safe place such as your wallet, not in the vehicle.
■
Panic mode (vehicles with wireless remote control)
■
When riding in an aircraft (vehicles with wireless remote control)
When bringing a wireless key onto an aircraft, make sure you do not press
any buttons on the wireless key while inside the aircraft cabin. If you are car-
rying a wireless key in your bag, etc., ensure that the buttons are not likely to
be pressed accidentally. Pressing a button may cause the wireless key to
emit radio waves that could interfere with the operation of the aircraft.
■
Conditions affecting operation (vehicles with wireless remote control)
The wireless remote control function may not operate normally in the following
situations.
●
Near a TV tower, radio station, electric power plant, airport or other facility
that generates strong radio waves
●
When carrying a portable radio, cellular phone or other wireless communi-
cation device
●
When multiple wireless keys are in the vicinity
●
When the wireless key has come into contact with, or is covered by a metal-
lic object
●
When a wireless key (that emits radio waves) is being used nearby
●
When the wireless key has been left near an electrical appliance such as a
personal computer
■
Key battery depletion (vehicles with wireless remote control)
If the wireless remote control function does not operate, the battery may be
depleted. Replace the battery when necessary. (
■
Replacing the battery (vehicles with wireless remote control)
P. 516
When
is pressed for longer than about
1 second, an alarm will sound intermit-
tently and the vehicle lights will flash to
deter any person from trying to break into
or damage your vehicle.
To stop the alarm, press any button on the
wireless remote control.
112
■
Certification for wireless remote control (vehicles with wireless remote
control)
For vehicles sold in the U.S.A.
FCC ID: GQ4-52T
FCC ID: GQ4-49R
NOTE:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful interfer-
ence, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
FCC WARNING:
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
<For 52T>
The FCC ID/IC Certification number is affixed inside the equipment. You can
find the ID/number when replacing the battery.
For vehicles sold in Canada
NOTE:
This device complies with Industry Canada’s license-exempt RSSs. Opera-
tion is subject to the following two conditions: (1) This device may not cause
interference; and (2) This device must accept any interference, including
interference that may cause undesired operation of the device.
<For 52T>
The FCC ID/IC Certification number is affixed inside the equipment. You can
find the ID/number when replacing the battery.
NOTE:
Le présent appareil est conforme aux CNR d’Industrie Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes:(1) l’appareil ne doit pas produire de brouillage; (2) l’util-
isateur de l’appareil doit accepter tout brouillage radioélectrique subi, même
si le brouillage est susceptible d’en compromettre le fonctionnement.
<Pour 52T>
L’identification FCC/Ie numéro d’accréditation IC est apposé(e) à l’intérieur
de l’appareil.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст