Toyota FJ Cruiser (GSJ 10, 15 series). Manual — part 249
IT–6
1GR-FE INTAKE – VACUUM SWITCHING VALVE
IT
REMOVAL
1.
DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINAL
2.
REMOVE V-BANK COVER (See page
3.
REMOVE AIR CLEANER ASSEMBLY (See page
)
4.
REMOVE NO. 1 VACUUM SWITCHING VALVE
ASSEMBLY
(a) Disconnect the connector.
(b) Disconnect the 2 vacuum hoses.
(c) Remove the bolt and No. 1 vacuum switching valve
from the intake air surge tank.
INSPECTION
1.
INSPECT NO. 1 VACUUM SWITCHING VALVE
ASSEMBLY
(a) Check the resistance.
(1) Using an ohmmeter, measure the resistance
between the terminals.
Standard resistance
If the result is not as specified, replace the
vacuum switching valve No. 1.
(b) Check the vacuum switching valve No. 1 for ground.
(1) Using an ohmmeter, measure the resistance
between each terminal and the body.
Standard resistance
If the result is not as specified, replace the
vacuum switching valve No. 1.
(c) Check the operation.
(1) Check that air does not flow from port E to port
F.
If the operation is not as specified, replace the
vacuum switching valve No. 1.
A126383
Ohmmeter
G036152E01
Tester Connection
Specified Condition
1 - 2
33 to 39
Ω at 20°C (68°F)
Ohmmeter
G036153E01
Tester Connection
Specified Condition
1 - Body
10 k
Ω or higher
2 - Body
10 k
Ω or higher
Filter
Air
F
E
FI06393E01
1GR-FE INTAKE – VACUUM SWITCHING VALVE
IT–7
IT
(2) Apply battery voltage across the terminals.
(3) Check that air flows from port E to port F.
If the operation is not as specified, replace the
vacuum switching valve No. 1.
INSTALLATION
1.
INSTALL NO. 1 VACUUM SWITCHING VALVE
ASSEMBLY
(a) Install the No. 1 vacuum switching valve with the
bolt onto the intake air surge tank.
Torque: 9.0 N*m (92 kgf*cm, 80 in.*lbf)
(b) Connect the 2 vacuum hoses.
(c) Connect the connector.
2.
INSTALL AIR CLEANER ASSEMBLY (See page
)
3.
CONNECT CABLE TO NEGATIVE BATTERY
TERMINAL
Torque: 3.9 N*m (40 kgf*cm, 35 in.*lbf)
4.
INSTALL V-BANK COVER (See page
)
Air
E
F
S004523E01
A126383
INTERIOR – FRONT FLOOR FOOTREST
IR–1
IR
BODY
INTERIOR
FRONT FLOOR FOOTREST
COMPONENTS
FOOTREST CLIP
FRONT FLOOR FOOTREST
FOOTREST CLIP
B130585E01
IR–2
INTERIOR – FRONT FLOOR FOOTREST
IR
REMOVAL
1.
REMOVE FRONT FLOOR FOOTREST
(a) Disengage the 4 claws and remove the front floor
footrest.
2.
REMOVE FOOTREST CLIP
(a) Remove the 2 footrest clips.
INSTALLATION
1.
INSTALL FOOTREST CLIP
HINT:
Use the same procedure for both sides.
(a) Engage the 2 claws and install the footrest clip.
2.
INSTALL FRONT FLOOR FOOTREST
(a) Engage the 2 studs and install the front floor
footrest.
B130586
B130587
B130588
B130589
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст