Toyota FJ Cruiser (GSJ 10, 15 series). Manual — part 206

ET–54

EXTERIOR – ROOF DRIP SIDE FINISH MOULDING

ET

9.

INSTALL ROOF DRIP SIDE FINISH MOULDING CLIP
NOTICE:
•

Only follow this procedure when replacing the
clips.

•

Wear polyethylene gloves when performing steps
and avoid having direct contact between the
adhesive and your hand.

•

Refer to the label on the adhesive for further
precautions.

(a) Clean the vehicle body.

(1) Using an industrial dryer, heat the tape

remaining on the painted surface to soften it
and peel it off with a bamboo scraper.

(2) Clean the surface using a shop rag or piece of

cloth soaked in a non-residue solvent.

(b) Apply adhesive.

(1) Load an adhesive cartridge into an adhesive

coating gun.

(2) Remove the cap from the adhesive cartridge

and pull the lever of the gun. Make sure that
the adhesive comes out of the nozzle tip ( 2
outlets) uniformly. (Confirm by applying
adhesive to cardboard)

(3) Pull the lever again and apply adhesive to a

part of the cardboard where it has not been
applied before.
HINT:
The amount of the adhesive applied in this step
should be greater than that required 0.5mm
(0.02 in.)

(4) Using a paddle, mix the adhesive 10 times.
(5) Apply the adhesive, with a uniform thickness of

0.5 mm (0.02 in.), to the surface of the
hardening tape on the clip.

(c) Set the clip in the predetermined position on the

pillar and press in until extra adhesive protrudes
beyond the sides of the tape (20 N (2kgf, 4.4 lb) x 2
seconds).
Specification:

(d) After pressing the clip, leave it for the predetermined

time shown below and then install the moulding.
Ambient temperatures and recommended
leaving times:

Location Marks

Location Marks

b

a

B135009E01

Area

Measurement

a

2.5 to 3.5 mm (0.098 to 0.138 in.)

b

2 to 3 mm (0.079 to 0.118 in.)

Temperature

Leaving times

5 to 10

°C (41 to 50°F)

1 hour or more

10 to 15

°C (50 to 59°F)

30 minutes or more

15 to 23

°C (59 to 73°F)

30 minutes or more

23

°C (73°F) or more

15 minutes or more

EXTERIOR – ROOF DRIP SIDE FINISH MOULDING

ET–55

ET

10. INSTALL NO. 4 ROOF DRIP SIDE FINISH MOULDING

(a) Engage the clip and install the No. 4 roof drip side

finish moulding.

11. INSTALL NO. 3 ROOF DRIP SIDE FINISH MOULDING

(a) Install the No. 3 roof drip side finish moulding as

shown in the illustration.

12. INSTALL NO. 2 ROOF DRIP SIDE FINISH MOULDING

(a) Install the No. 2 roof drip side finish moulding as

shown in the illustration.

13. INSTALL NO. 1 ROOF DRIP SIDE FINISH MOULDING

(a) Engage the clip and install the No. 1 roof drip side

finish moulding.

B135008

Location Mark

B135006E01

Location Mark

B135004E01

B135002

ET–56

EXTERIOR – ROOF DRIP SIDE FINISH MOULDING

ET

14. INSTALL ROOF DRIP SIDE FINISH MOULDING JOINT

COVER
HINT:
Use the same procedure to remove all the roof drip
moulding joint covers.
(a) Engage the 2 claws and install the roof drip

moulding joint cover.
NOTICE:
Install the roof drip moulding joint cover with
the arrow mark facing forward.

Arrow Mark

B135000E01

EXTERIOR – OUTSIDE MOULDING

ET–57

ET

BODY

EXTERIOR

OUTSIDE MOULDING

COMPONENTS

FRONT BUMPER
COVER

RADIATOR GRILLE

x4

3.0 (30, 27 in.*lbf)

N*m (kgf*cm, ft*lbf) : Specified torque

x4

x2

x2

x5

x2

x2

3.0 (30, 27 in.*lbf)

8.0 (80, 71 in.*lbf)

3.0 (30, 27 in.*lbf)

B134727E01