Toyota FJ Cruiser (GSJ 10, 15 series). Manual — part 458
SE–14
SEAT – FRONT SEAT ASSEMBLY
SE
22. REMOVE FRONT SEAT CUSHION LOWER SHIELD
RH
(a) Disengage the claw and remove the front seat
cushion lower shield.
23. REMOVE FRONT SEAT CUSHION LOWER SHIELD
LH
HINT:
Use the same procedure as for the RH side.
24. REMOVE FRONT SEAT CUSHION EDGE
PROTECTOR
(a) Remove the 2 front seat cushion edge protectors.
25. REMOVE SEAT POSITION SENSOR (for Driver Side)
(a) Remove the bolt and the seat position sensor.
26. REMOVE OCCUPANT CLASSIFICATION ECU (for
Front Passenger Side)
(a) Disconnect the 2 connectors.
(b) Using a screwdriver, disengage the claw and
remove the occupant classification ECU.
B130706
B130707
B130708
B130709
SEAT – FRONT SEAT ASSEMBLY
SE–15
SE
27. REMOVE FRONT SEAT WIRE (for Front Passenger
Side)
(a) Disconnect the 4 connectors.
(b) Disengage the claw and remove the connector.
(c) Using a clip remover, remove the 4 clamps and the
front seat wire.
B130710
SE–16
SEAT – FRONT SEAT ASSEMBLY
SE
REASSEMBLY
CAUTION:
Wear protective gloves. Sharp surfaces on the front seat
adjuster could cause injuries to your hands.
1.
INSTALL FRONT SEAT WIRE (for Front Passenger
Side)
(a) Install the seat wire with the 4 clamps.
(b) Engage the claw and install the connector.
(c) Connect the 4 connectors.
2.
INSTALL OCCUPANT CLASSIFICATION ECU (for
Front Passenger Side)
(a) Engage the claw and install the occupant
classification ECU.
(b) Connect the 2 connectors.
3.
INSTALL SEAT POSITION SENSOR (for Driver Side)
(a) Install the seat position sensor with the bolt.
Torque: 8.0 N*m (80 kgf*cm, 71 in.*lbf)
4.
INSTALL FRONT SEAT CUSHION EDGE
PROTECTOR
(a) Install the 2 front seat cushion edge protectors.
B130710
B130709
B130708
B130707
SEAT – FRONT SEAT ASSEMBLY
SE–17
SE
5.
INSTALL FRONT SEAT CUSHION LOWER SHIELD
RH
(a) Engage the claw and install the front seat cushion
lower shield.
6.
INSTALL FRONT SEAT CUSHION LOWER SHIELD LH
HINT:
Use the same procedure as for the RH side.
7.
INSTALL RECLINING ADJUSTER OUTSIDE COVER
RH
(a) Install the reclining adjuster outside cover with the
screw.
8.
INSTALL RECLINING ADJUSTER OUTSIDE COVER
LH
HINT:
Use the same procedure as for the RH side.
9.
INSTALL RECLINING ADJUSTER INSIDE COVER RH
(a) Engage the claw and install the reclining adjuster
inside cover.
(b) Tighten the screw.
10. INSTALL RECLINING ADJUSTER INSIDE COVER LH
(a) Engage the claw and install the reclining adjuster
inside cover.
(b) w/ Front Seat Side Airbag:
(1) Install the clamp.
(c) Tighten the screw.
11. INSTALL VERTICAL SEAT ADJUSTER BUSH (for
Driver Side)
(a) Engage the claw and install the vertical seat
adjuster bush.
B130706
B130705
B130703
B130704
B135121
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст