Toyota FJ Cruiser (GSJ 10, 15 series). Manual — part 327
ME–40
METER – METER / GAUGE SYSTEM
ME
(d) Reconnect the combination meter connector.
NG
OK
E13-1 (B) - Body ground
Always
11 to 14V
REPAIR OR REPLACE HARNESS AND
CONNECTOR
Terminal No.
Condition
Specified Condition
REPLACE COMBINATION METER ASSEMBLY
METER – METER / GAUGE SYSTEM
ME–41
ME
DESCRIPTION
The combination meter assembly controls the speedometer in accordance with vehicle speed signals
from the speed sensor or skid control ECU.
WIRING DIAGRAM
Speedometer Malfunction
for M/T:
for A/T:
Combination Meter Assembly
Combination Meter Assembly
Speed Sensor
Skid Control ECU
IG1
IGN
To IG1 Relay
To IGN Relay
IG+
SE
SI
SE
SI
SI
SP1
IG2
GND2
E126860E02
ME–42
METER – METER / GAUGE SYSTEM
ME
INSPECTION PROCEDURE
(a) Shift the shift lever (M/T) or transmission gear selector
lever (A/T) to the neutral position.
(b) Jack up the vehicle.
(c) Turn the ignition switch to ON.
(d) Check the voltage while turning the wheel slowly.
Standard
HINT:
The output voltage should fluctuate up and down as
shown in the diagram on the left when the wheel is
turning slowly.
OK
NG
(a) Check the vehicle's transaxle type.
Result
B
A
1
INSPECT COMBINATION METER ASSEMBLY
11 to
14V
0V
Turn Wheel
Combination Meter Assembly Connector:
E13
13
E126867E01
Tester Connection
Specified Condition
E13-13 (SI) - Body ground
Voltage generated intermittently
REPLACE COMBINATION METER
ASSEMBLY
2
CHECK TRANSAXLE TYPE
Transaxle Type
Proceed to
M/T
A
A/T
B
Go to step 5
METER – METER / GAUGE SYSTEM
ME–43
ME
(a) Remove the speed sensor.
(b) Connect the positive (+) lead from the battery to terminal
1 and the negative(-) lead to terminal 2.
(c) Connect the positive (+) lead from the tester to terminal 3
and the negative (-) lead to terminal 2.
(d) Rotate the shaft.
(e) Check that the voltage output between terminals 2 and 3
varies between 0V and 11V.
(f)
Reinstall the speed sensor.
NG
OK
(a) Disconnect the E13 combination meter assembly
connector.
(b) Disconnect the B44 speed sensor connector.
(c) Measure the resistance
Standard resistance
(d) Reconnect the combination meter assembly connector.
(e) Measure the voltage
Standard voltage
(f)
Reconnect the speed sensor connector.
NG
3
INSPECT SPEED SENSOR
Component Side:
Speed Sensor
1
2
3
E133751E01
REPLACE SPEED SENSOR
4
CHECK HARNESS AND CONNECTOR (SPEED SENSOR - COMBINATION METER
ASSEMBLY)
Wire Harness Side:
Speed Sensor Connector
Combination Meter Assembly Connector
B44
SI
IG+
SI
SE
E13
Front View
SE
E126862E01
Tester Connection
Specified Condition
E13-13 (SI) - B44-3 (SI)
Below 1
Ω
B44-2 (SE) - E13-4 (SE)
Below 1
Ω
Tester Connection
Condition
Specified Condition
B44-1 (IG+) - Body
ground
Ignition switch ON
11 to 14V
REPAIR OR REPLACE HARNESS OR
CONNECTOR
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст