Toyota FJ Cruiser (GSJ 10, 15 series). Manual — part 199
EXTERIOR – NAME PLATE
ET–27
ET
BODY
EXTERIOR
NAME PLATE
COMPONENTS
Non-reusable part
REAR NAME PLATE
NO. 2 BACK DOOR
NAME PLATE
NO. 1 BACK DOOR
NAME PLATE
B134739E01
ET–28
EXTERIOR – NAME PLATE
ET
REMOVAL
1.
REMOVE NO. 1 BACK DOOR NAME PLATE
(a) Apply protective tape to the back door panel in the
area around the No. 1 back door name plate.
(b) Using an infrared light, heat the No. 1 back door
name plate.
CAUTION:
Do not burn yourself with the heated back door
panel or infrared light.
HINT:
Heat at 40 to 60
°C (104 to 140°F) for 1 to 2 minutes.
(c) Using a gasket scraper with its tip wrapped in
protective tape, gradually peel the adhesive surface
and remove the No. 1 back door name plate.
(d) Remove the protective tape.
2.
REMOVE NO. 2 BACK DOOR NAME PLATE
(a) Apply protective tape to the back door panel in the
area around the No. 2 back door name plate.
(b) Using an infrared light, heat the No. 2 back door
name plate.
CAUTION:
Do not burn yourself with the heated back door
panel or infrared light.
HINT:
Heat at 40 to 60
°C (104 to 140°F) for 1 to 2 minutes.
(c) Using a gasket scraper with its tip wrapped in
protective tape, gradually peel the adhesive surface
and remove the No. 2 back door name plate.
(d) Remove the protective tape.
Protective Tape
B134740E01
Protective Tape
B134741E01
Protective Tape
B134743E01
Protective Tape
B134744E01
EXTERIOR – NAME PLATE
ET–29
ET
3.
REMOVE REAR NAME PLATE
(a) Apply protective tape to the back door panel in the
area around the rear name plate.
(b) Using an infrared light, heat the rear name plate.
CAUTION:
Do not burn yourself with the heated back door
panel or infrared light.
HINT:
Heat at 40 to 60
°C (104 to 140°F) for 1 to 2 minutes.
(c) Using a gasket scraper with its tip wrapped in
protective tape, gradually peel the adhesive surface
and remove the rear name plate.
(d) Remove the protective tape.
INSTALLATION
1.
INSTALL REAR NAME PLATE
(a) Clean the attachment surface.
(1) Using an infrared light, heat the double-sided
adhesive tape remaining on the back door
panel.
HINT:
Heat at 40 to 60
°C (104 to 140°F) for 1 to 2
minutes.
(2) Using a shop rag or piece of cloth, rub the
remaining double-sided adhesive tape off the
back door panel while it is hot from the infrared
light.
NOTICE:
Installing the rear name plate while any
double-sided adhesive tape remains on the
back door panel may cause adhesion
failure. Therefore, completely remove the
double-sided adhesive tape.
(3) Using a non-residue solvent, clean the
attachment surface.
(b) Align the 2 pins and install a new rear name plate as
shown in the illustration.
Installation position
Protective Tape
B134746E01
Protective Tape
B134747E01
Peeling Paper
Back Door Panel
Relief R End Line
b
a
B134748E01
Mark
Measurement (along surface)
a
49 mm (1.929 in.)
b
56.7 mm (2.232 in.)
ET–30
EXTERIOR – NAME PLATE
ET
NOTICE:
Install the rear name plate in an environment
where the ambient temperature is over 20
°C
(68
°F). If it is below 20°C (68°F), using an
infrared light, heat the back door panel and the
rear name plate up to 20 to 30
°C (68 to 86°F) and
install the rear name plate.
2.
INSTALL NO. 2 BACK DOOR NAME PLATE
(a) Clean the attachment surface.
(1) Using an infrared light, heat the double-sided
adhesive tape remaining on the back door
panel.
HINT:
Heat at 40 to 60
°C (104 to 140°F) for 1 to 2
minutes.
(2) Using a shop rag or piece of cloth, rub the
remaining double-sided adhesive tape off the
back door panel while it is hot from the infrared
light.
NOTICE:
Installing the No. 2 back door name plate
while any double-sided adhesive tape
remains on the back door panel may cause
adhesion failure. Therefore, completely
remove the double-sided adhesive tape.
(3) Using a non-residue solvent, clean the
attachment surface.
(b) Install a new No. 2 back door name plate as shown
in the illustration.
Installation position
NOTICE:
Install the back door name plate in an
environment where the ambient temperature is
over 20
°C (68°F). If it is below 20°C (68°F), using
an infrared light, heat the back door panel and
the No. 2 back door name plate up to 20 to 30
°C
(68 to 86
°F) and install the No. 2 back door name
plate.
Peeling Paper
Back Door Panel
Relief R End Line
b
a
B134745E01
Mark
Measurement (along surface)
a
37 mm (1.457 in.)
b
14.5 mm (0.571 in.)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст